The 2019 FIAT Albea is based on the design of the well-known Palio, which was produced as a " available car worldwide". In Russia, a modified version is being implemented sedan FIAT Albea, which is endowed with a voluminous trunk. It is worth noting that the cross-country characteristics allow the car to overcome even unpaved road sections without the risk of damage to the body.
Official dealers
- Region:
- Select region
Magnitogorsk, st. Marjani d.9
Moscow, Dukhovskoy per. d.17 p. 4
Murmansk, Kolsky pr. 110
All companiesThe appearance of the Fiat Albea 2019 is quite simple and concise. There is no catchiness in the design, which is quite practical. The front headlights give the car solidity, voluminous trunk visually hidden by the unusual shape of the hood, which makes it special, recognizable.
Also take a look at and .
On such a model it will be convenient to move even for people "in the body", as there are wide doorways, which, of course, acts clear advantage. side mirrors large enough - this creates good review and also increases safety while driving.
The relatively modest size of the vehicle is very convenient when parking, which is ideal in conditions of limited parking spaces.
Fiat albea white
available spacious plastic
in russia light steering wheel
test four new
In the photos of the Fiat Albea 2019 2020, it is noticeable that the manufacturer has made some changes to the model. The updated bumper is equipped with large air intakes, which added functionality to the car. New hood made more streamlined, improved headlights and fenders added elegance to this model. One of the most important advantages of the cabin can be noted silence when driving. Body elements fit very precisely, the noise from the engine can be heard only after 3 thousand revolutions / min.
It's time to get acquainted with the dimensions of the Fiat Albea 2019 2020:
- curb weight is 1045 kg;
- volume luggage compartment- 515 liters;
- wheelbase - 2439 mm;
- length is 4210 mm;
- width - 1703 mm;
- height - 1489 mm;
- ground clearance is 180 mm.
Let's go to the salon
The instrument panel is simple in execution, but all the data necessary for the driver on it is easy to read. The devices are endowed with a dark background decorated with red arrows. Thanks to this combination, the eyes are less strained and tired.
The center console is made in modern design. Seat adjustment allows for comfort for a driver of any height and size, as well as easy control vehicle. Seats for passengers are no less comfortable. The car can be easily transformed: if you fold the rear seats, it will become like a pickup truck. Quality upholstery lasts long term services, so you do not need to buy covers.
Among other things, the new car provides the following options:
- radio preparation (antenna, six speakers);
- computer;
- security systems;
- headlights corrector;
- followmehome device;
- central locking;
- power steering;
- electrically adjustable mirrors;
- electric front windows;
- foglights.
Midrange Specifications
Specifications The 2019 Fiat Albea is impressive. The model was created on the basis of a 1.4 l engine (77 hp) with 5 step box gears, gasoline consumption of 7 liters. Ground clearance of 18 cm makes it more functional. The great advantage is the possibility of operation in conditions dirt road no harm to the car.
Good permeability just helps out on modern roads Russia. Technical specifications allow for 13.5 seconds to accelerate to 100 km / h. The engine is quite economical, as in urban conditions it consumes 8.2-8.5 liters per 100 km.
The domestic consumer is also pleased with the semi-independent suspension: it is moderately rigid, it has perfectly proved its reliability on serious potholes. Chassis made "on the conscience": has impressive dimensions, made of durable metal. The accelerator, brake and gas pedals respond well to the requirements of the driver. Buyers can choose one of three trim levels Fiat Albea.
The price in Russia for Fiat Albea 2019 2020 depends on the configuration of the car. The cost of the first of them - Base - is 375,000 rubles and provides only for central locking, power steering, and an airbag for the driver.
Next comes Classic package, the price of which starts from 430,000 rubles. A computer, air conditioning, electrically adjustable mirrors, electric front windows, and foglights have been added to the equipment.
As you can see, the cost of this model is quite acceptable for a middle-income consumer, so the car is competitive in the market.
All for and against
Analyzing all of the above, we can conclude that Albea was very fond of domestic consumers. It is also worth noting that previous versions were no less popular and had many positive feedback. However, in addition to the benefits, this car there are also disadvantages. Let's take a closer look at them. The advantages of the new model include:
- comfort in driving;
- good sound insulation;
- spacious salon;
- volumetric trunk;
- economical fuel consumption;
- good permeability.
Among the shortcomings can be identified:
- outdated design;
- lack of a Russian-language on-board computer;
- expensive service.
Owners talk about their experience
Before buying this car, it will not be superfluous to read the reviews of the owners previous versions. After all, who, if not them, should know about all the "pitfalls" and the nuances of this machine.
Having studied the reviews on various thematic sites, it can be noted that among the main advantages they note a good ground clearance, spacious trunk, high-quality suspension, affordable price, comfortable lounge, smooth running. As for the main complaints, they relate to the weak power and modesty of the cabin.
Automotive Market Alternatives
The main competitors are Hyundai Accent , Renault Logan . Appearance budget car- not the main thing, so we will not compare the design. Often the driver is interested in the convenience of landing, control, visibility. Fiat is the leader in these parameters. Adjustable steering angle, variable seating height allow the driver to comfortably fit in the cabin. The chair with lateral support pleases with its profile and rigidity.
Comfortable enough to drive Hyundai Accent. However, the large thin steering wheel, low landing driver's seat creates inconvenience for people with small stature. Driver Logan partly devoid of comfort because the steering wheel is very tilted forward, and the seat cushion is located high from the floor. Gearbox and visibility are good in all three cars. It’s only a pity that it’s almost impossible for a passenger taller than average to sit behind the driver in Accent, and only two passengers will feel comfortable in the back seat, three of them are already cramped.
Now look at and .
FRONT SUSPENSION
Kinematic diagram of the front suspension. 1- ball bearing; 2-hub; 3-brake disc; 4-protective cover; 5-turn lever; 6-lower support cup; 7- suspension spring; 8-protective case telescopic rack; - compression buffer; 10-upper support cup; 11-bearing of the upper support; 12- top support of the rack; 13-rod nut; 14- stock; 15- compression buffer support; 16-telescopic rack; 17-nut; 18-eccentric bolt; 19- rounded fist; 20-shaft drive front wheel; 21-protective cover of the hinge; 22-outer shaft hinge; 23-lower arm.
Front suspension independent, MacPherson strut type, with telescopic shock absorber struts, coil springs, lower wishbones and stabilizer roll stability. The arrangement of elements of a forward suspension bracket on the car is shown on fig. 1, 2, 3, 4.
The main element of the front suspension is the telescopic shock absorber strut 1 (Fig. 2), which combines the functions of the telescopic element of the guide mechanism and the damping element of the wheel's vertical oscillations relative to the body. A twisted cylindrical compression buffer 4, a protective cover 5 of the strut and an upper support 1 are assembled on the shock absorber 1 (Fig. 1). Through thrust bearing, installed in the upper support, the load is transferred to the car body. The shock absorber strut with its lower part is connected to the steering knuckle 3 (Fig. 4) of the front suspension. Front suspension arm attached back to the cross member 2 (Fig. 3) of the suspension with the help of a silent block and a rubber bushing, and through the front part ball joint connected to the lower part of the steering knuckle of the front suspension. The crossbar, in turn, is attached to the side members of the body.
The anti-roll bar 1 with rubber pads mounted on it is connected to the cross member 2 of the front suspension and to the levers with four brackets.
Rice. 1. 1-Upper suspension strut support; 2-screw; 3-rubber cover; 4-upper support cup; 5, 7-washer; 6-spacer sleeve; 8-nut.
Rice. 2. 1-strut shock absorber; 2- spring; 3-nut; 4-compression buffer (chipper); 5-protective cover (anther); 6-bolt; 7-washer.
Rice. 3. 1-roll bar; 2-subframe; 3-nut; 4-inner pillow; 5-outer pillow; 6-bracket for fastening the inner cushion; 7, 8, 10, 13, 14 - screws; 9-sleeve; 11-bracket; 12 washer.
Rice. 4. 1-Swing arm; 2, 5, 6, 7, 8 screws; 3- rotary fist; 4-washer; 12 ball joint.
The front wheel hubs are mounted on double row angular contact ball bearings. Bearings for cars with and without ABC differ from each other by the presence of a magnetic strip. Those. on a car with ABC, you can install a bearing without a magnetic strip, but then the ABC system will not work.
Rice. 5. 1-outer CV joint; 3- nut; 7-bearing; 8- hub.
When replacing the front struts and front suspension springs, change these parts only in pairs (right and left at the same time)!
The FIAT Albea car is equipped with gas-oil front telescopic shock absorber struts. On sale under analogues substitutes are also sold gas-oil shock absorber struts.
Just oil and as some say "gas" on the horizon have not yet been seen!
OEM part numbers for front suspension.
Front pillar: original;: 51702390 (without ABS), 51702389 (with ABS).
analogues from the manufacturer: 51708823 (without ABS); 51708824 (with ABS).
Below are also analogues of front shock absorbers from other manufacturers, suitable for Albea 100%.
AM-4134 (without ABS) - (Conson, Türkiye); 
have rigid characteristics, do not differ much from the original.
CRX21056 (without ABS) - (Carex); 
FT-1013 (without ABS) - (Alco/Gober); 
ASG8824 (with ABS) - (Automotor, France); 
have soft characteristics. With them, the car rides more smoothly, hard hits "in the front panel" disappear. The changes are especially noticeable when rolling down a suburban highway.
FORCETECH PS 9710211 (with ABS) - (Maysan Mando, Türkiye); 
G16356 (with ABS) - (Monroe). 
shock absorber support left: Shock absorber support right:
original: 46760673. original: 46760674.
In many catalogs, shock absorber mounts beat the other way around and on FIAT Doblo they are installed the other way around (674-left, 673-right). In our car, the upper shock absorber mounts are installed in exactly the same order as above.
46466619 - shock absorber boot; 
46464298 - shock absorber bumper;
46777766 - rubber gasket for the spring;
7082812 - ball bearing;
46748579 - rear right silent block;
46748578 - rear left silent block;
46421522 - front silent block;
51744226 - outer stabilizer bushing;
51769073 - suspension arm assembly, right;
51769074 - suspension arm assembly left;
46828588 - knuckle rotary right;
51759339 - knuckle rotary left;
46776762 - hub bearing (without ABC);
46532573 - hub bearing (with ABC);
46738808 - inner stabilizer bushing, for stabilizer 46738806 (diameter 22 mm);
46738807 - inner stabilizer bushing, for stabilizer 46738805 (diameter 21 mm); 
46833041 - front spring.
In the "classic" and "comfort" car trim levels, the front springs have more rigid characteristics, in contrast to the "base" configuration. Outwardly, there are no differences, the difference lies in the marking of the springs. On the "base" - this is one white and two green dots; "classic" and "comfort" are one yellow and two brown dots.
Replacing the front struts and springs.
Before replacing old (killed) racks, it is necessary to carefully diagnose the condition of the above elements. So that later it would not be sad when you remove the rack and disassemble it into its components, you will understand that there are not enough new elements for repair, since it makes no sense to put the old ones back.
In case of failure of the front suspension struts working fluid(oil) gets on the protective rubber boot, thereby corroding it and rendering it unusable. Also, failures of the front suspension strut mounts are not uncommon. In general, to replace the front struts, in addition to the struts themselves, you may need:
- Dampers (chippers);
- Protective cover (anther);
- Upper supports shock absorbers;
- Springs.
Before replacing the front struts, you need to make simple measurements as shown in the photo below.
And if the dimensions you measured match and the size from the edge of the wing to the center of the wheel axle is standing car equal to 373 mm (photo 1) or less, then the front springs must also be replaced. Because in this case, the weight of the car is not spring-loaded, but lies with a polyurethane bump stop on the rack and the car suspension does not work. For those who have doubts about the correctness of the calculation, they can make the calculations themselves. In photo 2 there is the size of the full extension of the rod from the rack, photo 3 is a fender installed in its place (the height of our fender is 93 mm). 435 mm is the size from the edge of the wing to the middle of the wheel with the front wheel jacked up.
Optimal size from the edge of the wing to the middle of the wheel, installed without load on the ground car, for high-quality operation of the front suspension is - 385-390 mm.
And so, to replace the front struts and springs, you will need the following tool: a spanner wrench for 13 (upper rack mount), a spanner for 19, spring couplers, a hexagon for 6 (unscrew the top nut for 19 supports), an open-end wrench for 17 (compress the springs)
A-pillars AM-4134 (without ABS) - (Conson Turkey). 
Front springs Kilen 12161 
Comparison of old (stock) and new springs. 
Spring height 380 mm and bar thickness 12 mm absolutely identical to the springs installed at the factory.
As practice has shown, the Kilen 12161 front springs, with all the external attributes, turned out to be not very good. good quality. Slipped literally in the first months of operation. Therefore, I do not recommend these springs for installation on a car, the result will be the same: money spent in vain!
Front springs Taksim FT-3034 
They have the following dimensions Height 400 mm and bar diameter 12 mm. The difference in length is 20 mm, and in fact, the photographs show a more stretched method of winding. Such springs, judging by the catalogs, are intended for installation on vehicles equipped with diesel engine with a volume of 1.9 liters. Such springs are accordingly designed for a large load.
Anthers universal with chippers, Japanese made code 04-020 , where 020 stands for our stem diameter of 20mm and length of 98mm. The length of the fender had to be shortened by one ring, i.e. under the size of 84 mm (the size of the standard chipper is 93 mm). By installing anthers with bumpers of this brand, we simultaneously solve another childhood illness of our car - this is the knock of a plastic bumper on a metal support cup.
Below is another option.
Racks ASG8824 (with ABS) - (Automotor France) + boot Birth 51560 (new on the left) on the right, the old swollen from oil. The new one is indistinguishable from the original.
The appearance of the old racks that have served their purpose and the section of the used support.
Elimination of squeaks in the front suspension.
If characteristic squeaks occur in the front suspension (rubber crunch) after the car overcomes large bumps on the road (example: speed bump), the first thing to pay attention to is the two components of the front suspension that can make these sounds:
External stabilizer bar bushings;
- Front silent blocks front lower arms pendants.
Accordingly, we are trying to solve the problem of the occurrence of squeaks little blood, for this, first we replace the stabilizer bushings. Maybe this is where our search ends.
Remove any front wheel.
We unscrew the central mounts on both sides of the stabilizer and the outer mount of the stabilizer on the opposite side where the wheel was removed.
Change the stabilizer bushing.
Elimination of knocking anthers of the front struts
1. We jack up the front of the car so that the wheel hangs out. It is not necessary to remove the wheel - it does not interfere. We lower the duster down.
2. We cut out a ring with a diameter of 80 mm from rubber of any thickness. Inner diameter under the rod about 15 mm
3. We put this economy on the stock and lift the boot into place.
Behind the bumpers, the situation is similar to the front, in order to get rid of knocks, we perform a similar operation on the rear shock absorbers.
Do-it-yourself repair of the lower control arms of the front suspension. Experience of one of the owners.
First, let's get the accessories.
To press out the outer bushing of the front s / b, I purchased a s / b puller 2108 and 8 washers 30 x 16.
For pressing, I used a bushing of a suitable diameter and a bolt with a rocker arm from a universal bearing puller.
It turned out to be more difficult to remove the ball bearings and the old s / b, which did not fall out on their own, I had to cut, drill, saw the rubber in order to release the outer bushing of the front and the inner rear s / b. The bushing of the rear s / b is cut off by a grinder to the axis, torn off with a gas wrench, after which it is easily removed. To remove the ball joint, it is necessary to cut off the heads of the rivets with a grinder, and drill out the body of the rivets, or press it out with a press (if any).
The device-conductor for pressing the rear s / b had to be made by myself.
The process of pressing s / b is clear from the photo. We install the conductor on the lever, bait three bolts so that a small hole. in the lever coincided with small holes in the jig (for centering, you can use a drill with a diameter of 5 mm), tighten the bolts, drill a hole in the lever to a diameter of 6.1-6.2 mm and insert a pin with a diameter of 6 mm from good hardened steel (the drill shank bends when pressed ). We first wash the bushings and axles, then we press in the c / b. The nuance is only in the correct orientation of the rear s / b, which is done visually, combining the plane of the s / b bracket with the plane of the conductor corner.
Half day work with breaks.
Fiat Albea- Saltar a navegación, busqueda Fiat Albea Fabricante: Fiat Turquía Production: 2002 – presente Tipo: Auto compacto Tipo de carrocería: Sedan Motores … Wikipedia Español
Fiat Albea- Constructeur Fiat Années de production 2002 Moteur et transmission ... Wikipédia en Français
Fiat Albea- Fiat Fiat Albea 3G (seit 2004) Albea Hersteller: Fiat Produktionszeitraum: seit 200 … Deutsch Wikipedia
Fiat Albea- Infobox Automobile name = Fiat Albea aka = Palio / Palio Weekend / Siena / Perla manufacturer = Fiat assembly = Bursa, Turkey (jv with Tofas) Naberezhnye Chelny, Russia (SeverstalAvto) production = 2002 present predecessor = Fiat Siena successor ... Wikipedia
Fiat Albea- El Fiat Albea es un modelo World Car del Proyecto 178 de la Fiat construido en Turquía y esta pensada para paises en desarrollo en Europa del Este. Se ha producido desde 2002. El Fiat Albea es muy similar con el Fiat Siena fabricado en Brasil,… … Enciclopedia Universal
Fiat Palio- 4G (seit 2007) Fiat Palio Weekend 1G (1 … Deutsch Wikipedia
Fiat Automoveis
Fiat Group- Fiat S.p.A. Unternehmensform Società per Azioni ISIN ... Deutsch Wikipedia
Fiat SpA- Fiat S.p.A. Unternehmensform Società per Azioni ISIN ... Deutsch Wikipedia
Fiat Auto Monde- Cette liste regroupe les modèles automobiles qui ont été fabriquées dans un passé plus ou moins lointain ou sont actuellement toujours fabriqués (en caractères gras) dans les usines Fiat Group Automobiles ou sous licence Fiat Auto ailleurs qu en… … Wikipédia en Français
Books
- Book: manual / manual for repair and operation of FIAT ALBEA (FIAT ALBEA) gasoline since 2005 of release
- Book: manual / instruction for repair and operation of FIAT ALBEA (FIAT ALBEA) gasoline since 2005 of release in color photographs,. Repair, operation and maintenance Fiat Albea since 2005, with gasoline engines 350A1000 40;1.4L SOHC…
- Book: manual / instructions for repair and operation FIAT ALBEA (FIAT ALBEA) since 2005, PALIO (PALIO) / SIENA (SIENA) since 1998. gasoline / diesel , . Manual for the repair and operation of Fiat Albea since 2005, Fiat Palio / Siena since 1998, with petrol engines: 1, 2 8V 40; 60 l. With. 41;, 1, 2 16V…
Handling is good, average comfort, big trunk 550 liters, the cabin is comfortable in long trips you don’t get tired, the dynamics are rather weak, galvanized body, thick metal, excellent gearbox, clear inclusions, short lever strokes, the engine runs quietly, the sound insulation is average, the suspension is harsh, not pierced.
Fiat Albea, 2008
The car has good dynamics. The trunk is often larger than cars more high class. Clearance - what you need for summer residents. Consumption on the highway 5-5.5 l100. During the operation, not a single breakdown, spending only on changing oil and filters, the suspension is very reliable: in the spring of this year I checked it before traveling to Ukraine - no complaints.
Fiat Albea, 2007
The car is quite frisky and agile for its class, very economical, never let me down. Replaced after the diagnosis (as recommended) only salintbloki. There is a store where parts are a little more expensive than dozens. High ground clearance, the first car on which the back does not get tired (height lift and adjustment of the seatback curve). Add. ABS functions, 2nd airbags, power steering, el. glass lifts, transformation rear seats. Selling Fiat Albea due to poor health.
Fiat Albea, 2012
Bought in a car dealership in Tyumen Albea. Vparili for 430t. R. Divorced. Received without rugs, mudguards, fender liner, 0.5 liters of anti-freeze, gasoline for 20 km, in winter with summer tires, without seat adjustment, shameful drive mirrors, one name. They showed it warmed up, with seat adjustment. It seemed like nothing. But when you start it cold, it rumbles like a diesel. Warmed up constantly buzzes, exhausts the soul !!! Regretted that he got in. It would be better to take the Chinese. There are at least more options.
I bought this model almost by accident four years ago. It was 250 thousand rubles, and I wanted a non-domestic car. Fiat Albea passed by this several times in the market, but did not pay much attention. Finally, I’m already tired of choosing a car, so ... full review →
I want to write a review about my first car - Fiat Albea, because I know that many people read different reviews, opinions, critical articles, etc. before buying a car. Maybe my subjective opinion will come in handy for someone) I was the happy owner of this car 6 years old, ... full review →
I bought this car, after solving the housing problem, there was not much money left, but I needed a car to go to work, and go to the dacha, and be on wheels in the city. The “Six” of the father-in-law had to be given away upon the arrival of spring (many thanks to her - she helped out everything and ... full review →
Fiat car Albea 2007 release, with a mileage of 130,000 km. I bought the car in 2014 with my hands, I drove it for a year. In winter, the front spring burst, bought in existential for 1300 rubles. There were no more crashes. Before that, I had Toyota Cynos, Nissan Cube, ... full review →
Due to the limited budget wanted to buy Nexia, but after sitting in it I realized that it was not my car. Albeya chose by chance, going to the salon Elva Motors. It turned out that at that time there were discounts of 30,000 rubles. Thus, basic equipment cost 345,000 rubles. The cars were in ... full review →
I have 17 years of experience. I did not want to buy Fiat Albeya - my wife liked it! Traveled before this Korean cars. But as I sat down, drove - I liked it very much. Fiat took 8 months ago, very satisfied. Auto 2009 release, mileage 20,000 km. Acceleration is good, I didn’t squeeze 200 km / h, ... full review →
The device suits me. 13th car, not bringing problems. All the belts were changed by my wife and myself, and again I drove for 60 thousand km ... I only change oil, candles and filters, I don’t even look at the rest, but it’s been the fourth year ... In general, the Italians have everything ... full review →
I bought a used one with a mileage of 50 thousand km. Of course everything looked good and not alone, but still thought about investing in it. No shit!!! I changed the belts for 60 thousand - as it should be, examined and put it aside for every fireman - they look like new ones. So I only change filters and oil! ... full review →
I am completely satisfied with the car, the price and quality are comparable. drove 30,000, changed only pads, well, the oil panyatno! MOT did not go expensive. all by myself. that's the current liquid gur at a minimum dropped for 30 thousand. I am satisfied. Pros. inexpensive, comfort, good acceleration, big... full review →
I took the car used in 2007, with a mileage of 18,000 km. I took it in Autostart. A dual-use car was planned, that is, my wife and I planned to drive. She's at work, I'm on family business. The choice for money was between Kalina, shaggy Avea and Logan. When I sat down in Kalina, ... full review →
I am delighted with this device! How can you compare this car with other cars! I will say one thing with his 1.4, this is our 2. Pret 190 km per hour on the highway, this is a handsome man, I only change oils and put my own candles and change tires, I don’t do anything else. I need to look at the suspension...
