We change the wheel hub stud of the Hyundai Solaris if its thread is damaged, broken, or if the stud is bent.
1. We hang out and remove the wheel, securely fix the car on a factory-made stand.
2. Remove the disc brake mechanism.
To remove a damaged stud, the manufacturer recommends removing the wheel hub, which will require mandatory replacement new bearing.
3. We replace the stud without disassembling the hub assembly.
4. With a hacksaw or scissors for metal, we make two cuts on the brake shield.
5. With pliers we bend the freed part.
6. Using a hammer, knock out the damaged pin from the hub hole. It is also possible to shorten the stud (especially the bent one) by cutting the stud rod with a hacksaw or cutting machine - “grinder”, and then knock it out of the hub.
In order not to jam the threads on the new stud, you can make a small flat on its head. For example, with a file, or using a grinder.
7. Insert the pin into the hub hole.
8. We press the stud until its head stops into the hub flange, screwing onto the stud wheel nut through a suitable bushing.
It is convenient to use a large diameter nut as a sleeve. We assemble in the reverse order.
We will not tell our long story about how the hairpin broke and how we had to go to the store slowly and carefully. Usually, as you might guess, the stud breaks when working with the wheel, but it is relatively easy to replace it with a new one, and not only Hyundai example solaris.
We found a new part in nearest car store, also in the markets it is probably cheaper. Let's move on to the actual operation.
1. First of all, you need to have a set of standard tools and a jack on hand. We block the wheels and raise the part where you need to change the stud.
2. We unscrew the wheel, in our case the picture was unpleasant, you will see in the photo a little higher.
3. Now let's move on to dismantling the caliper. The operation is not at all difficult, you can look at us. From the back you will find two mounting bolts, after which we broadcast a caliper onto the spring so as not to stretch and / or deform the hoses. 
4. To dismantle brake disk With Hyundai Solaris you just need to unscrew the two bolts that are immediately visible between the studs. Sometimes, the disk sticks, so it's hard to give in. In such a situation, one comes out: to tap with reverse side until it comes out by itself. 
5. Now worth it new problem in front of us: you need to decide something with a protective cover, since it prevents you from pulling out the pin. On all forums they write that it is easy to bend it back, but in our case it began to deform greatly during such an operation. It was decided to make a small incision, which allowed it to be bent in two parts, as it were. 
6. We knock out the broken pin with a hammer and drive in a new one. It was very difficult for us to enter it, they even smeared it with grease and worked well with a hammer before fully inserting the pin. 
7. It remains to return the casing to its original position, of course, you can’t bring it to its original state, but it’s better than completely deforming it or cutting out pieces altogether.
That's all, in a couple of hours you can easily manage slowly and calmly.
Skoda introduced the updated Superb 2020
Skoda presented updated family superb. The flagship liftback and station wagon debuted at a private event in Slovakia. Having changed externally and technically, the model received advanced equipment and became the first hybrid car in the brand line.
Serial Kia XCeed tested without camouflage
Korean automaker KIA is testing the XCeed hatchback. Judging by the absence camouflage film these tests are final, the official presentation of the novelty will take place soon.
"Yandex. Auto" will help to remotely control the car
Services can be managed both through the menu and with the help of the voice assistant "Alice". Roman Chernin, head of Yandex geoservices, believes that cars will soon become a kind of gadgets, and their control will be more intuitive.
Audi announces ultra-luxury version of flagship A8
According to the Autonews portal, by 2021 the German brand Audi will be the most luxurious version of the flagship A8 sedan, which will receive the prefix "Horch". New top variant Audi A8 Horch will be able to compete with luxury cars Mercedes-Maybach.
Renault began accepting orders for the limited edition Arkana in Russia
Renault began accepting orders in Russia for a limited edition of its new product - the Arkana coupe-crossover. These are top-end cars with exclusive design solutions.
Cities with the most car thefts
Specialists of the insurance company AlfaStrakhovanie analyzed the appeals of clients insured under CASCO and named the cities of Russia where cars were most often stolen in 2018 and 2017. So, in 2018, the most hijackings were committed in St. Petersburg (0.33%).
Volvo recalls two models of cars in Russia
Volvo Cars announced the recall of 79 Volvo cars S90 and XC60 sold in 2018-2019. The reason for the withdrawal is the results of studies conducted Volvo Cars: Found that on the rail front seat flange nut may be missing.
Sales of new cars in Bashkiria increased by 0.4% in April
Sales of new cars in Bashkiria in April 2019 increased by 0.4%, to 5,510 cars. This was reported to UfaTime.ru by the consulting company Avtostat Info.
Introduced the most powerful Mercedes-Benz GLE
On American market the most powerful version crossover Mercedes-Benz GLE - GLE 580 4Matic with 490 hp engine. Under the hood of the GLE 580 4Matic is a 4.0-liter V8 unit equipped with two turbochargers.
2019 International Engine of the Year Award Winners Announced
The award ceremony took place as part of the Engine Expo exhibition in Stuttgart. In the vote for best motor 2019, 70 automotive journalists took part. According to them, the engine of the year was power unit A 3.9-liter Ferrari, he got 425 points.
Ravon cars will be assembled in Russia
Uzbek Ravon cars who can return to Russian market already this year, will collect on factory Derways in Cherkessk. The assembly production project was approved within the framework of economic cooperation between Russia and the Republic of Uzbekistan.
Replacing wheel studs Hyundai Solaris
You will need a ball joint pin puller.
1. Brake the car parking brake and install wheel chocks ("shoes") under the front wheels.
2. Raise back vehicle, securely jack it up and remove the wheel.
3. Remove the hub rear wheel(see Removal and installation of a nave of a back wheel).
4. Install the puller and press the pin out of the hub hole.
Note
In the absence of a puller, a damaged stud can be knocked out of the hub hole with a hammer through a soft metal spacer.
5. Using the wheel nut and the correct size bushing, press the new stud into the hub.
6. Install the removed parts in the reverse order of removal.
Solaris is one of the most reliable car models, but sometimes it needs repair. There are annoying troubles with the automatic transmission, and with the motor, with the wheels and their parts, including the studs.
How to change the front wheel stud Hyundai Solaris with your own hands?
Every motorist should have knowledge about the design of the car. How to change a stud on a Hyundai Solaris wheel? This is easy if you know exactly where the part is located in the wheel structure.
A standard wheel, not a steering wheel, but an ordinary one, consists of:
- disk;
- tires;
- carcass or code on which the tire is attached;
- hubs.
The tire is put on a disk, which is attached to the hub - the axis of strength of the Hyundai wheel structure. The stud is a structural element of the hub.
Wheel stud repair: features
Deformation of the stud causes it to be removed and replaced, otherwise driving performance wheels will drop.
Replacing a stud on a Hyundai Solaris wheel and repairing it consists of the following steps:
- The wheel is unscrewed;
- The disk is removed;
- The hub and bearing are removed.
- Hyundai Solaris rear wheel hub stud is being replaced. For this, two cuts are made with a hacksaw on brake panel, the stud is knocked out of the hub opening with a hammer, a new one is inserted and secured with a nut.
IMPORTANT: Replacing the rear wheel stud of a Hyundai Solaris does not differ from replacing a part for the front, and the cost self repair will be many times lower than in the cabin.
A bit about wheel covers
When replacing the front wheel stud of the Hyundai Solaris, attention must also be paid to the caps on the wheels. The individuality of the car owner is often emphasized by the choice of a cap - a detail that can become an element of tuning.
This eye-catching design protects the disc from dirt and radically changes the look of the car. The cap can be plastic or metal, have a flat or embossed shape.
Replacing studs Hyundai Solaris may be required in the event of a thread break or a break in the stud on which the wheel is screwed. Wherein hyundai studs Solaris stand for both front wheels and rear wheels. To replace the front and rear wheel studs, you will have to do approximately the same operations. After all, here and there disc brakes with floating bracket. We propose to consider the process of disassembly and assembly on the front wheel of the Hyundai Solaris.
For work, it is desirable to have a hacksaw (scissors), a file, a hammer, and a set of standard keys.
1. We tear off the wheel nuts.
2. We hang out the front part, finally unscrew the nuts and remove the wheel.
3. Shoot stopping support, for which you will have to unscrew the two bolts securing to the steering knuckle.
4. Remove the Solaris brake disc.
5. In order not to remove the hub, we change the stud immediately on the machine.
6. With a hacksaw or scissors for metal, we make two cuts on the brake shield.
7. With pliers we bend the freed part.
8. Using a hammer, knock out the damaged pin from the hub hole. It is also possible to extract the stud (especially the bent one) by shortening it by cutting the stud shaft with a hacksaw or cutting machine - “grinder”, and then knocking it out of the hub.
9. In order not to jam the threads on the new stud, you can make a small flat on its head. For example, with a file, or using a grinder.
10. Insert a new stud into the hub hole.
11. We press the stud until its head stops into the hub flange, screwing the wheel nut onto the stud through a suitable bushing.
It is convenient to use a large diameter nut as a sleeve. We assemble the Hyundai Solaris brake mechanism in the reverse order. If you change the stud with the removal of the hub, you will also have to wheel bearing replace, and it is quite difficult. Therefore, do not complicate your life.
