For traffic safety and extending the life of tires, it is necessary to visually check them before driving, maintain the required pressure in them, regularly (at least once a month) check it and bring it to normal.
The recommended tire pressures are indicated on the label affixed to the end of the left front door. The plate shows the air pressure values in the tires of the front and rear wheels when driving off the freeway and on the freeway.
plate Logan cars and Sandero
plate car Sandero stepway
It is also necessary to check the tire pressure when the ambient temperature drops or rises significantly and before driving a long distance.
When driving for a long time, especially on high speed, the tires heat up and the pressure in them increases. Therefore, air pressure should be checked with cold tires before driving.
If it is not possible to measure the pressure on cold tires, it is necessary to take into account the increase in air pressure in the tires from heating by 0.2–0.3 bar.
Loosen the wheel valve cap...
... and connect to the valve tire pressure gauge or pump with pressure gauge.
If the pressure is lower than required, we inflate the tire with a tire pump or compressor, controlling the pressure on the pressure gauge.
If the pressure is higher than required...
pressure gauge (or a suitable tool) on the valve spool, let the air out of the tire in small portions and check the pressure.
When operating a vehicle with a full load and a trailer, the tire pressure must be increased by 0.2 bar.
Tires must be free of bulges, tread separation and damage that exposes the cord. Residual height tire tread must be at least 1.6 mm.
Tire wear can be measured...
… by measuring the remaining tread depth with a caliper depth gauge.
Tires are not allowed different models on one axle, as well as tires that do not match in size technical requirements car manufacturer.
The manufacturer does not recommend changing wheels. If the tire treads of the front wheels are worn to the limit (wearing out approximately twice as fast as the rear ones), we recommend purchasing one wheel of the same model and putting it on the front axle together with a spare (not worn) wheel. We recommend replacing the least worn wheel (out of the replaced ones) in place of the spare wheel.
Regularly check the tightening of the wheel bolts and, if necessary, tighten the bolts.
If vibrations occur while driving on a flat stretch of road in a limited speed range, the wheels must be balanced by a tire shop. Vibration at all speeds can be caused by patchy tire wear, blistering or other damage, or deformation. rim. Damaged tires or disks are replaced.
Wheel rims should be kept clean to prevent corrosion. Places with a damaged coating can be cleaned with sandpaper, degreased, primed and painted.
If the owner of Renault Logan is interested in reducing fuel consumption own car, improved manageability, increased resource tires, then he will need to study information regarding the optimal value of air inflation in the tires. In this article, we will find out what tire pressure.
What factors affect airflow?
For Renault Logan, the manufacturer has provided for the installation of wheel disks with a dimension of 14 and 15 inches. For the 1.4-liter version, the smaller of the indicated disc diameters is provided, and for the 1.6-liter unit, a correspondingly larger one.
The pressure indicator is influenced by:
- disc diameter value;
- motor version;
The optimal air parameter favorably affects the resource of tires and suspension.
What is the best pressure for Logan tires?
The entire list of regulated parameters is given in the table available on driver's door(inner panel). Sometimes similar information can be placed on the back surface of the gas tank hatch.
The table has differentiated information about pressure, taking into account the magnitude of the load, the weather factor, the number of passengers, etc.
Still, it is not worth treating with absolute confidence the information provided by the manufacturer, because the indicated values \u200b\u200bimply the presence of original disks and rubber in Renault Logan. When the owner uses tires from an alternative manufacturer, he must determine the pressure indicator on his own.
How to measure pressure correctly?
For this purpose, a manometer will be indispensable. The correct indication of the indicated device is achieved if the car is idle for an hour or more. This is due to the following reasons:
- heating rubber during long drive;
- extension compressed air in the inner cavity of the tire under the influence of the temperature factor.
In Russia, tire pressure in any car, including Renault Logan measured in bars.
If the vehicle is expected to drive on bumpy terrain, then the pressure should be adjusted downward by 0.1 or 0.2 bar, respectively, for wheel sizes 14 and 15 inches. This action will lead to fuel efficiency and reduce the negative impact on the suspension components.
The season also affects the difference in indicators. Winter time involves reducing tire pressure by 0.1 bar from the regulated value, which improves stability on slippery surface.
If driving on a high-quality roadway is planned, then it is recommended to increase the pressure indicator by 0.2 bar, which is also accompanied by some fuel efficiency.
Tire pressure monitoring for its compliance with the regulatory values should be resorted to at least once a month.
Summing up
Now you know what tire pressure is optimal. Paying increased attention to the tire pressure indicator, the owner provides his car with a predictable behavior on the road. Do not neglect the frequency of control and timely bringing the value to the regulatory indicators, taking into account the amendments we have made, and your Renault Logan will become a faithful companion when overcoming any distance.
Tires in the car - the most important detail vehicle. Our main support, literally and figuratively. It is they who are rubber hard workers who take on all the blows of our unpredictable Russian roads.
Today we will talk with you about what tire sizes are equipped with stepway cars at the factory, as well as what sizes of rubber can be used on Stepways without any problems.
First about regular tires, which are equipped with Stepway cars at the factory.
Let's start with the first generation of Stepways. On cars that were produced before 2014, the Avtoframos plant installed regular tires tires size 185/65/15. It is this size that is considered to be "native" for Stepway-1 and it is recommended to use it on a car. Finding wheels of this size is not difficult - they are on sale everywhere.
Stepway-I on stock summer tires 185/65/15
As for the “non-native” tire sizes on the Stepway, which can be safely put on regular disks, then their range is not too wide.
The most ideal "out of stock" tire size for a first Stepway is 195/65/15. This size without any problems is stretched on a native disk. You can buy it and feel free to install it. The same applies to the size 195/60/15.
Winter tires 195/65/15 on Stepway-I
Also, tires 195/70/15 will fit on the native wheels of the first Stepan.
Some motorists go to experiments and put wheels of size 200 and above on the Stepway. For example, 205/65/15. In principle, such tires can be put on "Stepan". Although, it seems to us that there is not much point in using such wheels on the first Stepway. Firstly, it is an order of magnitude more expensive, and secondly, significant deviations from the standard tire size are always a “pig in a poke”. And the greater the deviation, the more risk fuck serious problems with a car. However, it's up to you, of course...
The same goes for wheels and tires with a radius of 16. Many motorists put them on the Stepway-I for the sake of appearance. On the Internet, we came across instances on which their owners put tires 205/65/16. We highly recommend not to conduct such experiments.
Well, we finished with the first series, now we are smoothly moving on to the second generation Stepways. These wonderful cars from the factory are equipped with tires that are already larger - the 16th radius. The native wheel size for the second Stepway is 205/55/16.
Without any problems, tires 205/60/16, 205/55/16, 195/55/16 are installed on the second Stepway.
As for the options with the installation of rubber bigger size, we have already mentioned this above. The main message here is that you conduct all experiments at your own peril and risk. For example, on the Internet, the owners of the Stepways, who tried to put wheels with a size of 215/65/16 on their native wheels, reported that they had failed - the wheel rubbed against the arch when the steering wheel was unscrewed. Therefore, friends, be prudent when choosing rubber and do not engage in perversions. Your car won't appreciate it.
But as for the rubber of a smaller radius, then it is quite possible to put it on the Stepway II. For example, tires 195/65/15, 205/60/15, 205/65/15 are well suited to the second "Stepan". But does it make sense?
Size 16 wheels on the Stepway-II look more solid than size 15 wheels on its predecessor. In the large arches of the Stepway, the wheels of the 15th radius are simply lost and do not look very presentable. This is especially true of the huge rear arch. On the second generation of Stepways, this is already better, although rear arch there is also a big one.
In general, the flight of thought among our car owners is very wide and many steppe growers conduct risky experiments, trying to pull on stepway tires more suitable for SUVs.
In any case, if you decide to put rubber on your Stepway, which is very different in its parameters from the standard one, we advise you to measure it seven times first, that is, think carefully, weigh the pros and cons, discuss the issue with your “colleagues” on specialized sites and forums, and only then go to the store for tires.
Concluding our today's conversation about tires for Stepway, I would like to say that after all best size tires are native, i.e., recommended by the manufacturer. Well, or at least minimally different from the native.
That's all, good luck on the road and do not forget to share your experience in installing tires of various sizes on the Stepway in the comments to the article.
OUR PARTNERS:
Website about German cars
Lamps used in the car
Any modern passenger car or freight car can be serviced and repaired independently, in a regular garage. All that is required for this is a set of tools and a factory repair manual with a detailed (step-by-step) description of the operations. Such a manual should contain the types of applied operating fluids, oils and greases, and most importantly - the tightening torques of all threaded connections parts of components and assemblies of the car. Italian cars – Fiat Alfa Romeo Lancia Ferrari Mazerati (Maserati) have their own design features. You can also join a special group select all french cars – Peugout (Peugeot), Renault (Renault) and Citroen (Citroen). German cars complex. This applies especially to Mercedes Benz ( Mercedes Benz), BMW (BMW), Audi (Audi) and Porsche (Porsch), in a slightly smaller - to Volkswagen (Volkswagen) and Opel (Opel). next large group, isolated by design features are American manufacturers - Chrysler, Jeep, Plymouth, Dodge, Eagle, Chevrolet, GMC, Cadillac, Pontiac, Oldsmobile, Ford, Mercury, Lincoln . Of the Korean firms, it should be noted Hyundai / Kia, GM - DAT (Daewoo), SsangYong.
Recently Japanese cars have a relatively low initial cost and affordable prices for spare parts, but recently they have caught up with the prestigious European brands. Moreover, this applies almost equally to all brands of cars from the land of the rising sun - Toyota (Toyota), Mitsubishi (Mitsubishi), Subaru (Subaru), Isuzu (Isuzu), Honda (Honda), Mazda (Mazda or, as they used to say, Matsuda) , Suzuki (Suzuki), Daihatsu (Daihatsu), Nissan (Nissan). Well, and the cars produced under the Japanese-American Lexus brands(Lexus), Scion (Scyon), Infinity (Infiniti),
Why is it so important to use only correctly inflated tires? From the state it's in wheelbase, not only fuel consumption depends, but also the safety of the driver and passengers during movement. The tire pressure of Renault Duster, Logan or Sandero should always be normal. As a rule, the manufacturer indicates such indicators on the car itself - in the area of \u200b\u200bthe door on the driver's side or in the place of the filling tank.
Car tire pressure gauge In addition to the fact that with properly inflated tires, the car will be operated competently and carefully, the correct use of the entire chassis of your Renault Logan or Duster will be ensured. By the way, this rule applies to all vehicles.
Table of standard tire pressure for Renault Logan cars How to measure pressure correctly
Tire pressure cannot be determined by eye. Outwardly, you can only notice any deformations on the tire itself. This will only work if the vehicle is systematically driven with the wrong air/tire size ratio. Then various deformations are formed on the tread.
It is possible to accurately measure the pressure in the chassis of the Renault Logan or Duster (this also includes Sandero and Scenic) only with the help of special pressure gauges. According to the mechanism of operation, the following types of this equipment are distinguished:
- turnouts;
- electronic.
Mechanical pressure gauge for car tires The most accurate among these devices is considered to be electronic. The error here is no more than 0.05 bar. If you do not plan to perform such procedures systematically, you can use mechanical type device. True, such devices can be called accurate only with a stretch.
Recommended literature on the repair and maintenance of Renault Logan 2:
RENAULT LOGAN II petrol since 2014, repair manual
More
RENAULT LOGAN 2 petrol since 2014, repair manual
More
RENAULT LOGAN 2 / DACIA LOGAN 2 / LOGAN MCV petrol / diesel from 2012 onwards
More
RENAULT LOGAN gasoline since 2005, + restyling in 2010
More
Please note that in winter it is better to measure the pressure only with an electronic pressure gauge. Other types of devices may show incorrect results.
Standard tire pressure Renault Sandero Pressure standards for Renault
This brand of vehicle is quite peculiar. It is impossible to inflate tires “for all occasions” here. Based on the requirements that are prescribed in the instruction manual. The tire pressure for Renault Logan (Duster, Scenic) should be as follows:
- if the diameter of the disks is 14 cm - 2.0 kgf / cm²;
- with a diameter of 15 cm - 2.1 kgf / cm²;
- at maximum load 0.2 kgf / cm² must be added to the indicators;
- when using a loaded trailer - increase by 0.8 kgf / cm²;
- when driving on sandy terrain, the pressure must be reduced, but not more than 1 kgf / cm².
Table with standard tire pressure for Renault Scenic It should also be taken into account that when driving on snow or wet road indicators should not change.
Specialists at the service station will not only check correct pressure in the tires of your "Logan" or "Duster", but also pump up or lower it to the optimum condition. There you can also find out exactly what pressure for a particular brand of car is correct.
If you plan to travel long distances, it is better to measure the pressure before the start of the trip or after at least 3 hours have passed since the vehicle has come to a complete stop.
Correct pressure measurement
It is necessary to measure the pressure on Renault Logan (the same applies to Duster, Scenic). Taking into account the following conditions:
- only in the "cold" state of the car (for the last 3 hours, the mileage is not more than 1.5 km);
- tires must be cold.
Also take into account that you need to take readings from all 4 wheels. Spare wheel should also be systematically tested.
Table with standard tire pressure for Renault Duster cars Measurement process:
- the protective cap is removed from the manometer;
- by means of a special button, the readings on the device are reset;
- the device is mounted on the bus;
- by pressing the valve, readings are taken.
Based on the readings on the pressure gauge, the tire is pumped up or lowered.
Checking car tire pressure Consequences of incorrect pressure
Why is it important to maintain the correct air volume ratio in a tire? If the pressure is systematically in an incorrect state. The following negative consequences are possible:
- fuel will be spent inappropriately;
- road grip will deteriorate significantly;
- there is a risk that the tire will burst while driving, which will lead to an accident.
Besides, chassis the car is just falling into disrepair. Agree, the repair of almost the entire wheelbase of the Logan or Duster will be much more expensive than buying a monometer.
If you do not have the opportunity to perform such operations on your own, regular technical inspections of the Renault Duster should be carried out at the service station. The better you treat your vehicle the longer it will last you.
