The designation of the Hyundai accent fuse box. Hyundai Accent Wiring Diagram

↵

In each car, the function of overvoltage protection in electrical equipment is performed by the fuse box. The Hyundai Accent car is equipped with three such blocks, two of which are in the cabin, and one is under the hood.

The cause of the breakdown of the fuel pump, cigarette lighter, audio system or other electrical equipment may be a blown fuse. Their wiring diagram can be found at reverse side lining that protects the mounting block.

Mounting block under the hood Accent

Description of the wiring diagram of the engine compartment "black box" of this Hyundai Accent model:

Element marking	Decryption
	Generator
	Emergency gang, horn, electrically heated rear window, interior lighting
	Main lighting
	Ignition coil
	Radiator fan
	Heating fan
	Sound signal
	Salon lighting
	Audio system and radio
	heat exchanger
	Air conditioner
	fog lights
	Idling
	Radiator fan
	Air conditioner
	heat exchanger
	Engine
	Heat exchanger and air conditioner
	Klaxon
	fog lamps
	Head light right
	Head light left
	Dimensions front and rear on the right side
	Front and rear dimensions left side
	parking lights
	Generator
	Heat exchanger and air conditioner
	Power windows
	ABS system
	dipped beam
	Fuel pump
	ABS system
	diode socket
	diode socket
	Heating fan

Cabin Fuse Blocks

One of the cabin blocks on the Hyundai Accent is located to the left of the driver's foot. To gain access to it, you need to remove the plastic cover that closes the torpedo. After removing the overlay, you can see 18 fuses that are responsible for the operation of electrical equipment.

Description of the Hyundai Accent cabin fuse box, which is located on the left side of the driver:

Element marking	Decryption
	Control turn lights
	Responsible for ABS electrical circuits
	Functionality dashboard
	Responsible for the operation of the security system
	pointer management reversing, box "automatic"
	Responsible for locking doors
	Emergency management
	brake lights
	Heated glass rear
	Control of power windows, headlight washers, fog lights, engine cooling
	Electric washer windshield
	Seat heating control
	ABS circuit
	cigarette lighter
	Responsible for the operation of electric mirrors outside
	Air conditioner control

Another Hyundai Accent fuse box is located in the cabin behind the “glove box” (glove compartment). It contains not fuses, but relays, the function of which is to protect powerful Hyundai energy consumers.

Description of the cabin fuse box Hyundai Accent, which is located behind the glove box:

Relay marking	Decryption
	Responsible for work brake system. If this element fails, then the car can lead to the side when braking.
	Controls the operation of the rear fog lamps
	Ensures the functioning of the motor on the car Hyundai Accent
	Controls the lighting in the salon and luggage compartment, as well as near and high beam And parking lights
	Operation of the electric washer and cleaner windshield
	Element that controls the ABS system
	Power window control
	Responsible for the operation of electrical heating rear window
	Controls work sound signal
	Ensures the operation of turn indicators and light signaling

Video about cabin fuses for Hyundai Accent:

How to remove and replace the fuse box Accent

Replacement procedure this device Even beginner motorists will be able to do it. But still, some nuances are worth knowing, for example, that the replacement of the black box takes place with the battery disconnected and the ignition off.

Fuse block replacement algorithm:

1. Using the description of the wiring diagrams, determine which element is to be replaced.
2. Disconnect the battery, for this it is enough to disconnect the terminal that carries the negative charge.
3. Open the plastic cover that protects the fuse box on the Accent Tagaz. This can be done by hand or with a flathead screwdriver.
4. Using special tweezers or by hand, pull out the burned-out element. If there are doubts about the operability of the fuse, then it is enough to see if a fusible thread passes inside. If not, then the element must be replaced.
5. Install new part instead of the faulty one and check its performance. In this case, the power of the new element must match the power of the extracted one. If this is not possible at the time of replacement, then a part with a lower rating can be temporarily installed.
6. Close the mounting block with a plastic cover and connect the battery.

   Important! Before disconnecting the battery, the vehicle ignition must be switched off.

The function of the fuse box is to protect against overvoltage and failure of the electrical equipment of the machine. Therefore, when, for example, headlights, a stove, or a gas pump stop working in your car, check the fuses first. Maybe they are the cause of the problem.

Before you buy fuses or any hyundai spare parts, let's determine which of the fuses is responsible for what in the car.

There are three fuse boxes in the Hyundai Accent. Two are in the cabin, and the third is under the hood.

Fuse box in the engine compartment. And a list of what each detail is responsible for.

Fuse box in the cabin. It is located below the steering wheel, on the left. To get to it, remove the decorative trim on the dashboard.

The second block is located behind an additional glove compartment in the cabin. There are relays that protect powerful energy consumers in the car.

Relay number and what it is responsible for:

1. Responsible for the distribution of braking forces. In the event of a breakdown during braking, the car "leads".
2. Responsible for the rear fog lights.
3. This is the main relay for the Hyundai Accent. In the image, the relay is disconnected from the connector.
4. Follows the headlight bulbs.
5. Responsible for the operation of the windshield wiper and washer motor.
6. Responsible for the operation of the ABS.
7. Responsible for the operation of power windows.
8. Responsible for the rear window heating mechanism.
9. Responsible for the operation of the steering horn.
10. Ensures the operation of turn lamps and light signaling.

Any novice motorist can change the fuse.

1. Disconnect the battery first. Open the hood and remove the negative terminal.
2. Now open the cover of the mounting block. You can pry it off with a flathead screwdriver or some other hand tool.
3. Now you need to check the fuse. Remove it with tweezers or hands and check visually. There is a fusible thread inside the fuse. It may break or burn out. Such a component becomes unusable.

Remember! The new fuse must be the same rating as the one you removed.

1. Now check if the problem is fixed by connecting the battery. If so, don't forget to replace the cover.

4.5 Rating 4.50 (2 Votes)

In the Hyundai Accent, as in any other car, fuses are a kind of protection for the electrical equipment of the car. If the wiring is shorted, they can burn out. In this case, it is enough to replace one of the elements of the fuse block, and you can continue to enjoy a comfortable ride.

To eliminate the incorrect operation of the cigarette lighter, brake light or dimensions, you need to know the location and number of the fuse responsible for the failed electrical circuit. This car has 2 blocks with protective elements.

Fuse box Hyundai Accent under the hood.

IN engine compartment block with protective devices And relay located behind the battery. Its cover is fixed with plastic clips. After opening you can see fuse location, and extract desired element. The block has special tweezers for removing burnt parts.

Fuse box in the cabin Hyundai Accent

In the cabin, the protective elements are located on the dashboard (on the left side of the steering wheel). The block contains fusible links responsible for electrical devices salon, for example, cigarette lighter, signal fuse, door opening lights, etc. To remove the burnt device, just open the plastic cover. On the inside, there is a diagram showing fuse location in the block.

With the above information, you can fix the breakdown of one of the electrical appliances in a car of this brand at no additional cost. Now you will no longer have questions about where to look for the fuse and how to replace it.

DESIGN DESIGN

Onboard network car - direct current, with a rated voltage of 12 V. The electrical equipment is made according to a single-wire circuit: the “negative” conclusions of sources and consumers of electricity are connected to the “mass”: the body and the main units, which act as a second wire. At idle engine switched on consumers are powered by the battery, and after starting the engine - from the generator alternating current with built-in rectifier and electronic voltage regulator. When the generator is running accumulator battery is charging.

All electrical circuits vehicle (except for the starter power circuit) are protected fuses set in mounting block fuses in the passenger compartment and the mounting block of the relay and fuses in the engine compartment. Powerful consumers (headlights, cooling fan motor, electric fuel pump, etc.) are connected through relays installed in the relay box in the passenger compartment and the relay and fuse box in the engine compartment.

Hyundai Accent (TagAZ). M RELAY AND FUSE BOXES

The relay and fuse mounting block is located on the left in the engine compartment. The location of the fuses and relays is indicated on the outside of the cover. The relay box in the passenger compartment is located under the instrument panel behind the additional glove box. To replace the relay, open the storage compartment

Mounting block for relays and fuses in the engine compartment:

1 - fuse 100 And the generator circuit; 2 - fuse 50 A complex (circuits of the electric door lock, alarm, brake signals,rear window heatingsound signal, interior lighting lamp, ECU);3 - fuse 30 And the chains head lamps and side light; 4 - fuse 20 A control unit circuit engine; 5 - 30 A fuse for starting the engine and ignition coils.6 - fuse 20 A fan circuit radio ra system engine cooling, 7 - wiring connector,8 - fan relay heater. 9 - horn relay,10 - fuse 10 A interior lamp circuits. 11 - fuse 10 A of the circuit of the head unit of the system sound reproduction.12 - relay 2 condenser heat exchanger fan systems conditioning,13 - clutch relay air conditioning compressor,14 - fog relay socket headlights; 15 - backup fuse socket;16 - fuse 15 A regulator idle move and camshaft position sensor.17 - fuse 10 A circuit of the engine control unit.18 - radiator fan relay of the engine cooling system;19 - 10 A fuse for the air conditioner switching circuit;20 - relay 1 of the fan of the heat exchanger of the condenser of the air conditioning system;21 - 10 A fuse for the engine control unit circuit,22 - 10 A fuse for the air conditioning compressor clutch circuit,23 - fuse 10 A horn circuit;24 - 15 A fuse for the fog lamp circuit.25 - 10 A fuse for the right headlight lamp circuit.26 - 10 A fuse for the left headlight lamp circuit;27 - 10 A fuse for the side light lamp circuit on the starboard side of the vehicle;28 - fuse 10 A side light lamp circuits port side car ; 29 - marker lamp relay Sveta; 30 - generator pre-excitation resistor; 31 - starter relay, 32 - fuse 20A fan circuit condenser heat exchanger siems kindlylimitedin, 33 - a 30 A pre-protector for the power window circuit. 34 35 - a socket of the relay of permanently switched on low beam; 36 - relay fuel pump;37 - fuse 30 A block circuit ABS control;38,39 - diode socket; 40 - 30 A fuse for heater fan circuit

Relay box in the cabin:1 - turnip electronic distribution braking force (EBD); 2 - relay fog light in the rear lights3 - the main relay of the engine management system (for clarity, the mount is disconnected);4 - head light relay;5 - windshield wiper and washer relay;6 - ABS relay; 7 - power windows relay;8 - rear window heating relay,9 - the relay of a sound signaling device;10 - turn signal relay and alarm

We lift the box and remove it from the latches, opening access to the relay.

To access the fuse mounting block, open protective cover under the instrument panel to the left of the driver's feet. On inside cover shows the layout of the fuses in the block. Replacing relays and fuses is carried out in the same way as described in sec. (cm. " Replacing the relay and fuses of the engine management system", With. 74).

fuse mounting blocktel in the cabin: 1 - 10 A fuse for direction indicator circuit;2 - 10 A fuse for ABS circuits, control lamps in the instrument cluster;3 - 10 A fuse for the instrument cluster circuit;4 - 15 A fuse for the airbag circuit;5 - 10 A fuse for the circuits of the engine control unit, reversing light lamps, control unit automatic transmission gear;b- 10 A circuit fuse electric drive door locks;7 - 10 A fuse for the alarm circuit;8 - fuse 10 A of the brake signal circuit;

9 - 20 A fuse for the heated rear window circuit.10 - fuse

10 A circuits of the windings of the headlamp relay. power windows, headlight washer, air conditioning condenser heat exchanger fan, engine cooling system radiator fan, fog lights. fog light in rear lights .11 - 20 A fuse for the windshield wiper and washer circuit. 12 - 10 A fuse for the seat heating circuit (option), 13131 134 ..

Hyundai Accent is a fairly common car in a wide range of car owners. Over the years, the model has managed to take root on the streets of many cities. The older the car becomes and the less frequently technical inspections, the higher the likelihood that there will be problems with the electrics and appliances. In case of such malfunctions, the fuses and hyundai relay Accent. If the manual is not at hand, this article will help you.

List of fuses in the block under the hood

1 (100 A) - generator. If the battery began to discharge quickly, it is most likely the alternator and the lack of battery charge. Check this fuse, alternator belt tension, alternator connector pins, and wiring. There must be no short circuits in the car circuits. Check the voltage at the generator terminals with the car running (if there is no experience, it is better to contact an electrician).

If there is no voltage at the terminals, the brushes inside the generator may have worn out, in which case it can be repaired inexpensively. If squeaks are heard when turning the pulley or extraneous sounds most likely the bearings have failed. In this case, it is better to replace the generator with a new one or send it in for repair.

2 (50 A) - door lock.(electric drive), brake lights, alarm, horn, heated rear window, interior lighting, the electronic unit control (ECU).

If none of them work for you stop signal(including the cabin on the rear window), check this fuse first. If it is intact, then most likely the matter is in the “frog” (switch in the block above the brake pedal), connector or wiring.

If only one brake light does not light up, the lamp is most likely burned out. The lamps are double-filament, one thread for the size, the other for the stop. You can measure the voltage at the lamp connector with the brake pedal depressed, if it is there, it's in the lamp. If not, it's most likely wiring. See also the lamp connection diagram on the "Schemes" tab at the top of the page.

If it doesn't work" emergency gang“- check this fuse, fuses 1 and 7 in the passenger compartment and relay 10 in the passenger compartment, and then the power button and wiring.

If not working klaxon(beep), the case may be in this fuse, in the horn device itself, the wiring to it and the switch on the steering wheel. Try briefly applying 12V from the battery directly to the signal terminals. If no sound is heard, repair or replace it. It's pretty common problem especially in rainy weather. If there is sound, check the ground contact, it must be securely screwed. Wires should not have breaks and melted insulation.

If not working rear window heating, also check fuse 9 and relay 8 in the interior mounting block. If they are OK, check the contacts of the heating elements for rear rack, as well as the threads on the glass for breaks.

Detected breaks can be repaired with a special conductive adhesive. You can check the voltage at the contacts of the heating elements, when the button is pressed, it should be there. If there is no voltage at the terminals, check the wiring laid along the body and the operation of the button.

3 (30 A) - head light and lamp dimensions. If the head light or dimensions lamps do not light up, also check fuses 27, 28, then in the passenger compartment relay 4, the lamps themselves, connector contacts, wiring and switch.

4 (20 A) - engine control unit. If the engine does not start, does not run smoothly, or stalls without visible reasons, check this fuse and its contacts, as well as fuses 5, 6, 16, 17, 18, 21, then fuse 5 and relay 3 in the passenger compartment. In addition to wiring, it may be in the fuel system, fuel pump, ignition system, candles and other component systems. If there is no experience, it is better to spend complete diagnostics engine in .

5 (30 A) - engine start, ignition coils.

6 (20 A) - radiator fan. If the engine cooling fan does not turn on, also check relay 18 and fuse 10 in the passenger compartment. Try to apply 12 V voltage from the battery directly to the fan, thereby eliminating the possibility of its breakdown. It could also be a coolant temperature sensor (DTOZH) or a thermostat. When symptoms appear elevated temperature If the engine overheats, turn it off immediately. Otherwise, you can end up with expensive repairs. If there is no experience, it is better to contact the workshop.

7 - connector.

8 - heater fan relay. If your stove has stopped working and it’s cold in the cabin, check this relay, as well as fuse 40. If the heater only works in the maximum speed, check the resistor that is responsible for the fan operation modes. If necessary, replace it with a new one. If the stove does not work in any of the modes, try applying 12 V directly from the battery to its motor.

To get to the motor, you need to remove the cover under the main glove box. If the motor does not work, it will need to be repaired or replaced with a new one. If you have the funds, it is better not to skimp and buy a new one. If the motor is running, check the wiring and the operation of the stove mode switch (along with its contacts).

9 - horn relay

10 (10 A) - interior lighting. If the light in the cabin does not light up, in addition, check fuse 2, the serviceability of the lamp and contacts in the ceiling, and the wiring. If the light does not come on only when the doors are opened, check Limit switches on the body, which react to the opening and closing of doors.

11 (10 A) - head unit of the audio system, radio. If the radio does not turn on, check this fuse, then remove it and check the contacts in the connectors on the back, as well as the fuse that is located directly on the wire (usually red). Wiring can also be the cause. Check where the power is supplied to the radio, from the ignition switch or directly from the battery. If to the right wires apply 12 V directly from the battery, the radio should turn on. If it does not turn on, it is most likely a malfunction inside it and it needs to be repaired or replaced.

12 - relay 2 of the fan of the heat exchanger of the condenser of the air conditioner. If the air conditioner stops working, check, in addition, fuses 13, 19, 20, 22, 32, as well as fuses 10 and 17 in the passenger compartment. If they are all OK, there may be no freon in the system and you need to refuel. It will not be superfluous to check the entire system and pipes for tightness and the absence of leaks. In winter, it is recommended to occasionally turn on the air conditioner so that it does not cause problems in the spring.

Look also at the compressor under the hood, when the mode is on, its clutch should spin. If it does not spin, either there is no freon, or one of the component systems is faulty.

13 - air conditioning compressor clutch relay. See previous paragraph.

14 - fog lamp relay. If none of the fog lights work, check, in addition, fuse 24, then fuse 10 and relay 2 in the passenger compartment. The front and rear PTFs are turned on with different buttons. Check the contacts and serviceability of the corresponding button on the dashboard, as well as the wiring. If only one “foglight” does not light up, check the voltage at its connector and, if present, replace the lamp.

15 - reserve.

16 (15 A) - idle speed controller (XX), position sensor camshaft(DPRV).

If the engine does not hold idling, won't start, stalls, or runs erratically, check this fuse as well as fuel system and fuel pump. The reason may be in addition to electricians in poor quality fuel, spark plugs, nozzles and other components. If there is no experience, it is better to contact the diagnostic station.

17 (10 A) - engine control unit. See information about fuse 4.

18 - radiator fan relay. See information about fuse 6.

19 (10 A) - air conditioning. See information about fuse 12.

20 - relay 1 fan of the heat exchanger of the condenser of the air conditioning system. See 12.

21 (10 A) - engine control unit. See 4.

22 (10 A) - air conditioning compressor clutch. See 12.

23 (10 A) - sound signal. See 2.

24 (15 A) - fog lights . See 14.

25 (10 A) - head light lamp with right side .
26 (10 A) - headlight lamps on the left side. If both headlights are not working, see 3. If one headlight works and the other does not, check one of these fuses, as well as the serviceability of the lamp and contacts in its socket.

27 (10 A) - front and rear lamp side light on the right side.
28 (10 A) - front and rear side light lamps on the left side. If none of the indicator lamps are lit, see 3. If the lamps on only one side of the vehicle are not lit, check one of these fuses, the lamps and their connectors.

29 - lamp relay dimensions. See 3.

30 - generator pre-excitation resistor. See information about fuse 1.

31 - starter relay. If you turn the ignition key and the starter does not turn, check this fuse. If it is working, check the battery charge and the fastening of the terminals on it. They could oxidize or relax. Clean them inside with a sandpaper or a round file and fasten them well to the battery terminals. If after that the starter does not start to turn, check it by closing 2 contacts with a screwdriver or a metal object.

Before doing this, make sure the gearshift lever is in the neutral position. If the battery is charged and the starter does not work when the contacts are closed or 12 V is applied directly to it, most likely it is out of order. In this case, repair (replacing brushes or other worn parts) or buying a new one can help. If the starter only works with direct voltage, check the wiring and the ignition switch. Perhaps the tracks in the lock are oxidized or there is no contact in the connector.

32 (20 A) - fan of the heat exchanger of the condenser of the air conditioning system. See 12.

33 (30 A) - power windows. If none of the power windows work, in addition to this fuse, check relay 7 in the passenger compartment. If the power window does not work in one particular door, check the wires between the door and the body (they often break in this place), the control buttons on the door, and also the lift mechanism itself. To get to it, you need to remove the door trim. All cables must be in their grooves, the gears must be intact and the motor must work. Also check that there are no foreign objects in the mechanism.

34 (30 A) - anti-lock braking control unit ABS system . If ABS system stopped working for slippery surfaces and the wheels lock up when braking, check this fuse. If it is intact, it may be in the ABS unit, which is located under the air filter. The motor could fail in it or its brushes could wear out.

35 - low beam relay, permanently on. If both low beam headlights do not work, check this relay, as well as lamps and wiring. Both bulbs could burn out. If only one headlight does not light, check the lamp and the contacts in the connector. The lamps have 2 threads - one for the low beam, the other for the high beam.

36 - fuel pump relay. If the fuel pump stops working and the sound of its operation is not heard when the ignition is turned on, check this relay and the wiring in the cabin to the pump. The wires are usually laid under the driver's door sill and further along the body. Check that the wires are not damaged, melted or twisted.

If twists are found, they must be soldered securely. If you installed an alarm, then you probably set additional relay to block the fuel pump. In this case, check it too. This relay is usually located behind the small glove compartment. You can also apply 12 V to the fuel pump directly, thereby checking its performance.

37 (30 A) - ABS control unit. See 34.

38.39 - diode socket.

40 (30 A) - heater fan (stove). See 8.

Fuses in the cabin

The fuse box is located in the passenger compartment and is located below, at the left foot of the driver.

1 (10 A) - direction indicators. If the turn signals stop working and none of them light up, check, in addition to this fuse, also relay 10 in the passenger compartment and a relay installed separately under the steering wheel. If the relay is collapsible, you can remove the case and check the board for burnt tracks or blackened parts. Or replace it with a new one that is known to be good.

Then check the steering column switch, the health of the tracks and contacts in it, as well as the contacts in its connector and wiring. You should also check the lamps, which could burn out all at once. If only one turn signal does not work, most likely the problem is also in the lamp. Replace with a good one and check the contacts in the connector.

2 (10 A) - ABS, pilot lamps on the dashboard. If ABS does not work, see 34.
If the lamps on the panel do not work, check this fuse, the lamps themselves and the wiring.

3 (10 A) - devices on the panel. If your dashboard stops working, some of the devices work, and some don’t, most likely it’s the contacts on the panel board, or connectors. If this fuse is good, try to move the connectors on the back of the panel. Check the contacts in them and the wires. It may be necessary to remove and disassemble the entire panel to get to the boards inside it. Boards should be inspected for broken or burned tracks and other visible marks. short circuit, lack of contacts.

4 (15 A) - airbags. If at least one airbag has worked for you, then for the previous level of safety you will need to replace the deployed airbag module, block SRS control and belts. The driver's pillow is located in the center of the steering wheel, the passenger one is above the glove box.

5 (10 A) - engine control unit, reversing lamps, automatic transmission control unit.
If you have engine problems, see fuse 4.
If, when you turn on the gearbox on reverse gear reversing lights do not light up, check the lamps themselves and their connectors, then the reverse gear switch, which is located on the gearbox in the upper part, and the wires coming from it. To get to it, you need to remove the battery and air filter. Through the received space, access to it will open. Replace with a new one or repair the old one if it fails.

The location of the reverse sensor on the gearbox

6 (10 A) - central locking, electric door lock. If only one door stops closing or opening, check the electric drive of the lock so that it is in good condition and does not jam, and there is also enough lubricants. The case can also be in the actuator (block with the board) or the relay inside it. The actuator is located in the door, looks like small box. It supplies a short-term voltage of 12 V to electric locks of the required polarity (one polarity for opening the locks, the other for closing them).

Appearance of the door actuator block

7 (10 A) - alarm. If the “emergency gang” stops working, check, in addition, fuse 2, the correctness of the button and its contacts, wiring, and the lamps themselves.

8 (10 A) - brake lights. See information about fuse 2.

9 (20 A) - heated rear window. See 2.

10 (10 A) - power windows, headlight relay windings, headlight washer, air conditioning condenser heat exchanger fan, cooling radiator fan, fog lights (front and rear).
If the power windows do not work, see 33.
If the fog lights do not work, see 14.
If the radiator fan does not work, see 6.

11 (20 A) - windshield wiper and washer. If the “wipers” do not work, check, in addition to this fuse, relay 5. If they are serviceable, most likely it is the motor or the wiper mechanism. The motor is mounted on the rear wall of the engine compartment in the direction of travel on the right side, near the shock absorber strut.

You can disassemble the entire mechanism, the trapezoid, check the health of the motor by applying a voltage of 12 V to it, inspect all the rods and connections, clean and lubricate the rubbing and moving parts with WD or similar lubricants, then assemble the entire mechanism and re-check the operation of the wipers. If the purifier mechanism is old, then some parts could “stick”, in this case the best option will replace the entire trapezoid assembly. Its minimum price is in the range of 500-1000 rubles.

12 (10 A) - heated seats. If your seat heating stops working, check the contacts in the connector under the seat, as well as the wiring and the power button. Sometimes the issue may be heating elements inside the seat, where the wires could break off.

13 (10 A) - ABS. See 34.

14 - reserve.

15 (15 A) - cigarette lighter. If the cigarette lighter stops working, check this fuse, the antennae inside the socket so that they do not close and are in place. If the fuse blows when the connector is inserted into the socket, most likely you are connecting a low-quality device, with a non-standard connector that closes or deforms the contacts. Also check the contacts and wires at the cigarette lighter socket under the panel. They should be 12 V.

16 (10 A) - electric mirrors. If one of the mirrors is no longer adjustable, it may be in the button or its contacts. Also check that there are no foreign objects or ice in the mirror mechanism. Try gently moving it with your hand. Check the wiring and connector, for this you need to remove the trim and the corner on the mirror.

The mechanism of the motors in the disassembled rear-view mirror

17 (10 A) - air conditioning. If the air conditioner does not work, see 12.

18 - reserve.

Relay in the cabin

The relay box is located in the passenger compartment behind the small glove box.

1 - relay of the electronic brake force distribution system EBD.

2 - rear fog lamp relay.

3 - the main relay of the engine management system.

4 - head light relay. See information on fuse 3.

5 - windshield wiper and washer relay. See information on fuse 11.

6 - ABS relay. See prev. 34.

7 - relay electric windows . See prev. 33.

8 - rear window heating relay. See prev. 2.

9 - horn relay. See prev. 2.

10 - relay direction indicators, alarm. See prev. 1.

Connection diagrams

Diagram of wiring harnesses laid along the body

Wiring diagram for brake lights

Hyundai Accent fuses and relays in the heating, ventilation and air conditioning system

1 - power supply +12 V
2 - +12 V power supply, the main engine control relay is on
3 - +12 V power supply, ignition on
4 - fuse and relay box ( engine compartment)
5 — cabin block fuses
6 - stove fan fuse
7 - air conditioning compressor clutch fuse
8 - fuse for power windows, relay windings for headlights, headlight washer, air conditioning condenser heat exchanger fan, radiator fan, front and rear fog lights

9 - stove fan relay
10 - connector
11 - to the headlight washer relay
12 - air conditioning compressor clutch relay
13 - connector
14 - to the cabin relay unit
15 - automatic transmission control unit
16 - cabin fuse box
17 - air conditioner fuse
18 - stove fan motor
19 - engine control unit (ECU)
20 - from the block on the dashboard wiring harness
21 - stove fan motor resistor (heater operating modes)
22 - pressure switch
23 - air conditioner switch
24 - air conditioning compressor clutch
25 - from the block on the dashboard wiring harness
26 - stove speed switch (heater fan operation modes)
27 - thermal switch
28, 29 - to the block on the dashboard wiring harness