Installing turn signals in the mirror. We install turn signals in mirrors ourselves in a garage

Driving safety always remains a priority for every driver. He is responsible not only for himself, but also for his passengers. “Turn signals” were developed specifically for this purpose. are able to indicate the direction in which they are turning vehicle to optimize vehicle movement. One of the innovations of the “Chinese craftsmen” is a mirror turn repeater. We'll talk about installing it today.

The turn signal on the mirror duplicates the signal indicating the direction of travel

Device base

The installation of such equipment is an original and worthy decoration for the car. Due to its versatility, the repeater can be attached to any vehicle. The turning device is a small plate-shaped device. This textileite base is quite durable and equipped with LEDs. There are some model options: mounting in a reflective surface or installing a flexible “signal” on the corners of the mirror. They are inexpensive, but you can make them yourself.

Principle of operation

A repeater is attached, responsible for the rear view. They connect to the original turn signals to produce similar information. When the driver turns on the turn signal, the factory and installed devices will display the same data. Signal duplication will also add originality to the appearance of the car.

Present on the market ready-made models, which require only manual installation. But you can make turn signals in the mirrors yourself - this is a fairly easy process that will require:

• LEDs or ready-made “turns”;
• scotch;
• 2 elements causing a resistance of 180 Ohms and 0.5 W;
• wire 20 cm long;
• marker for marking;
• soldering iron

Installation process: detaching

If you are interested in turn signals in mirrors, first you need to dismantle the reflection elements. To detach the reflective surface from the mirror, carefully snap off the fasteners. After this, you need to disassemble this element and the plastic base. Usually the mirror is inserted into a special frame and secured with glue or tape. To do this, you need to heat the surface with a technical hairdryer for five minutes, then the elements should be freely removed.

Marking and power supply

At self-assembly device, it is important to correctly indicate the mounting locations for the LEDs. Installation of repeaters in mirrors is done using a marker, which is used to draw a figure of nine circles on the back side of the reflective surface. This number of light bulbs is quite enough to ensure comfortable visibility. After this, the shape is glued to the mirror with tape, and the LEDs are installed. It is important that they are matched in polarity. They need to be attached with the luminous side.

The next step is to solder the wires. To begin with, they are stripped and divided into five veins. Then they need to be twisted together. A resistance of 180 m is soldered one by one to the negative wire. Now it is checked whether there is power.

Cleaning the mirror

In order for the arrow to be visible through the reflective surface, it must be cleaned of excess material. When the entire structure has been checked for functionality, and the markings coincide with the location of the light bulbs, you need to make small holes in the amalgam. LEDs must be clearly visible through the reflective surface. Next, you need to clean the holes with a hacksaw to remove sharp edges. It is important to remember that not all mirrors are made of glass. If the model is made of plastic, it will be enough to lower the resistance to 140 Ohms. In this case, the brightness of the bulbs will be able to pass through the plastic.

Putting it back together

Many people notice that installing turn signals in mirrors creates a loose fit for the LEDs. To do this, you need to warm up the back panel in the places where the light bulbs are located with a hairdryer. But under no circumstances should you heat the fasteners! After sufficient heating, press the structure against the glass - it will bend a little and connect firmly. After a couple of minutes, you can move on to the last stage.

Wiring

In this process, it is enough to transfer the “minus” to the body, and the “plus” needs to be taken out from the door and connected to the on-board network. After this, the device will be the same as the rear turn signals.

Such manipulations are available to every motorist. By spending a small amount of time, you can get high-quality mirrors with repeaters. This method is completely safe and only requires attention to the stages of work. In this way, you will be able to increase your safety on the road yourself, because it is not always possible to notice rear turns. In the case of mirrors, they will always be clearly visible to drivers from behind.

From personal experience I would like to say that a repeater is useful trick. It is unusual for our places, so it is always noticeable, and, therefore, effective.

The turn signal on the mirror is a rather interesting decoration for the car and an original tuning step. Read below to find out what this device is, its characteristics, operating principle, as well as installation instructions.

[Hide]

Device characteristics

Repeaters can be attached to absolutely any vehicle. This is a fairly universal device, which is a plate equipped with LEDs.

Purpose and principle of operation

The repeater is installed on side windows, which are responsible for moving backwards. They can be said to exchange information with the original turn signals. This is done in such a way that when the driver turns on the turn signal, both devices - both the standard one and the repeater - will show similar data. Seeing duplicated values ​​on the car will also add some flair.

On automotive market You can easily find ready-made models that require manual installation, however, by the way, the device can be made with your own hands. It is not difficult to make turn signals for mirrors with your own hands; it will require only minimal skills and desire on the part of the driver or mechanic (author - Tver Garage).

Installation instructions

Installing turn signals in mirrors requires some tools and skills. Read more about this case below.

Tools and materials

To install the device you will need:

• repeaters;
• file;
• 10mm wrench and Phillips screwdriver;
• glue;
• steel wire.

Stages

Repeaters are installed in mirrors as follows step by step:

1. First you need to dismantle the car mirror, that is, disconnect the fasteners and remove the mirror surface.
2. Next, detach the plate from the plastic fastening. If the mirror is in a plastic frame, you can remove it with a hairdryer if you heat the surface of the desired point for a while. If it is glued hermetically, then to remove the mirror surface it is necessary to simultaneously heat it on both sides for about 5 minutes. Afterwards it can be removed. If it is attached with double-sided tape, then you also need a mounting frame.
3. If the mirror has automatic heating, then you need to carefully separate it to make some space for the repeater LEDs.
4. Next, you need to create arrows where the LEDs will be attached. For marking, a regular notebook sheet is used, where the future figure is drawn with dots. About nine LEDs can be installed on one mirror.
5. After marking, you need to duplicate the design on the tape with a marker. And stick the LEDs on the tape, taking into account the polarity. The LEDs are attached to the sticky side of the tape.
6. After this, you need to take the wire, strip it and separate the five wires, which must be twisted together and soldered between the soldered LEDs and thin wires. The resistance when soldering the negative wire should be 180 Ohms.
7. Next, you should remove the mirror for mounting the LEDs, immediately after the previous point has been checked for serviceability when power is applied. Now you need to make a hole in the amalgam so that the LEDs that match the markings are better visible through the mirror element.
8. You need to take a hacksaw and remove sharp holes from the mirror surface. This is done to clean the glass.
9. If the mirror is made of plastic, you can lower the resistance to 140 Ohms. Thus, the LEDs will break through the plastic and there will be no difference as such.
10. At this stage you can begin assembly. Due to the LEDs installed on the mirrors, difficulties may arise with the tightness of the rear panel. To solve this problem, just warm it up with a technical hairdryer. problem area, where the LEDs come into contact. Important: fasteners and latches must not be heated to avoid deformation.
11. As soon as the plastic is heated to the desired temperature, it must be pressed firmly to the surface of the glass. In this form, you need to hold the mirror a little so that it “sits.”
12. The final step is to connect the wires. The negative wire must be connected to the car body, and the positive wire to the vehicle. After that useful device will work properly, duplicating the meaning of the turn signals, and your car will become even more interesting and individual.

IN last years various types tuning is flourishing, despite the authorities’ ban on installing certain lighting devices. Today it is very popular LED lights. It is installed both inside and outside the car.

We will look at how to install a turn signal on a mirror yourself. There is nothing complicated about it, but it looks quite interesting. This type tuning significantly facilitates maneuvers, since for participants traffic you become more visible.

Where to start?

It looks much better with a turn signal, you will see that for yourself. You need to understand that there are several ways to implement your plan:

• installing LEDs directly on the mirror;
• installing a repeater in the rear view mirror housing.

The first option is simple, but quite effective. The second one is suitable for those who want to install a turn signal on the mirror from specific car. Let's consider both options. But first, I would like to say that such tuning is needed not only for beauty, but also for increased safety while driving the car. A striking example is rearranging from row to row. A neighboring car, which is half a car away from you, may not see the rear turn signal, and this increases the accident rate. The repeater on the mirror is clearly visible.

We buy everything you need for tuning

The number of elements that we will install is not that large, and therefore they will cost you little. The main thing is not to forget anything and buy everything you might need. IN this list includes:

• 18 SMD LEDs;
• transparent high-quality tape;
• resistance elements (180 Ohm and 0.5 W);
• technical hair dryer;
• small soldering iron;
• 20 centimeters of wire and a thin marker.

Having the above tools is essential, so buy them all. For example, it is not necessary to purchase a soldering iron. Most car enthusiasts already have it. You can also ask a neighbor for a hairdryer or rent it for a couple of days. Everything else isn't that expensive. Well, now let's move on directly to the installation process.

We do quality work

The first stage is dismantling the mirror. There should be no difficulties here, since everything is extremely simple. First you need to remove the mirror from the housing. Manufacturers use three main methods of fastening: with sealant, tight fit in the case and installation with double-sided tape. In order to get the mirror, you need to warm up the case, then remove it without any problems and start marking.

This stage, although important, since the type of repeater depends on it, is extremely simple. Take a sheet of paper in a cage and put dots at regular intervals. These are the locations of future LEDs. Next, glue the tape to a sheet of paper and duplicate the marks on it. After this, we glue the LEDs to the tape, not forgetting about the polarity.

Soldering and assembling the structure

Next, we take the pre-prepared wire and separate 5 cores from it. They need to be twisted and tinned. After this, we connect the LEDs in parallel and solder thin wires. On negative wire solder a 180 ohm resistance. Connect the power and check operation. If everything is functioning, then the side mirrors with turn signal are almost ready. If not, we look for a fault in the circuit.

In order for the LEDs to be visible through the mirror, it is necessary to make corresponding holes in the amalgam. Remember also that not all products are glass, there are also plastic ones. In the latter case, you can try to reduce the resistance to 140 Ohms. The brightness of the LEDs will increase and they will be visible through the plastic. To install the mirror back, the body needs to be heated with a hairdryer. It is not recommended to heat latches and fasteners, as they may become deformed. As for the wiring, we hook the negative wire to the body, and lead the plus wire to the car's electrical system through the door.

Installing a repeater in the case

Here everything is somewhat more complicated, since you will need to cut the plastic case. It is extremely important not to rush at this stage, as any inaccuracies will result in a loose repeater fit or an unsightly appearance. You can take a repeater from any car - it all depends on your preferences. There are also turn signal indicators on universal mirrors. Their advantage is quick installation and availability of all the necessary wiring for connection. In our case, the wires need to be selected and pulled independently.

The easiest way to install a turn signal is on left mirror, Although significant difference No. The most important stage is cutting the linings. Everything needs to be done carefully and not in a hurry. After this you can start checking and reassembly. One more thing - you need to find the wires going to the right and left turn signals. Getting to the wiring harness is not always easy. It is located at the threshold of the car and passes through the cabin.

Conclusion

Easiest to do led repeaters on the mirror, if there are standard ones on the trims. This is due to the presence of the wires we need. Although if they are not there, then there should not be any difficulties in finding them. The turn signal on the mirror may not work if the resistor is not connected. Although it will most likely function, the LEDs will burn out due to voltage surges.

In general, everything is implemented quite simply. Universal repeaters can be used. Their main advantage is that they are already assembled. All you need to do is remove the mirror, install the LEDs and connect the wiring. There is no longer any need to manipulate the sheet of paper. But it all depends on you. You may want a different color or size of the arrow, or perhaps choose a completely unusual shape for the latter. There are many possibilities here, but how you implement them depends only on your imagination. In general, the turn signal on the mirror is a necessary and interesting thing. Why not do such a craft in your free time, especially if you have the desire and opportunity.

Car mirrors – important elements security. Features a simple design and compact size. Can be installed in any production car, regardless of the make and model of the car, body type and equipment level. They differ in shape and appearance. Compatible with body design and general design interior

They improve visibility for the driver and allow them to assess the situation on the road. Simplify the movement process in reverse and prevent accidents and incidents. They contribute to safer performance of various maneuvers on the road (changing lanes, overtaking, avoiding obstacles, etc.). Car mirrors, depending on the installation location, are divided into 2 types - interior and side.

How does a car rear view mirror work?

1. Cases. It comes in different shapes, most often oval or rectangular with rounded edges. The design of the housing must be injury-proof, without sharp edges.
2. Reflective element. Passes information to the driver. It is durable glass with a special reflective layer and an additional protective coating. For safe operation Vehicles are not allowed to have chips, scratches or abrasions on the car mirrors that could affect the quality of the display. It should not distort color, increase or decrease the distance to objects, or change their shape.
3. Devices for adjusting the tilt of the reflective element. Allows you to adjust the viewing angle of the optical element.
4. Fastening mechanism. Provides fixation of car mirrors at the installation site. The fastening must be reliable as when driving on the road good quality, and when the vehicle shakes on defects in the road surface.

Additionally equipped with a folding mechanism. It should work smoothly and without jerking. Folding the mirror requires force. If the mechanism has minimal resistance, the optical element may suddenly collapse when moving high speed or during severe body shaking.

Types of car mirrors

1. Salon (internal). Installed inside the cabin using a durable bracket. Securely attached but easily adjustable. The standard shape is rectangular with rounded edges.
2. Lateral (external). Cars are equipped with two side mirrors. One is on the left, and the second is on the right.

In addition to the main functions of safety and accident prevention on the roads, they perform decorative functions. They complement and transform the appearance of the car. For example, stylish side mirrors (“swift” in shape with beautiful turn signals) give the car’s exterior sporty features.

On right-hand drive cars (“Japanese”) used in the Russian Federation, for convenience and safety of driving, an additional side mirror is installed on the hood.

About the panoramic mirror

Panoramic rear view mirror

The panoramic rear view mirror belongs to internal type car mirrors. It has a spherical optical element and is longer than a standard flat mirror. Provides more complete rear visibility, reducing the number of “dead spots”. Helps improve visual perception, increases viewing angle (up to 160 degrees on both sides). Main disadvantage– distortion of the real distance from the car in which the driver and passengers are located to the object.

Uniformity of curvature is one of the main requirements for a panoramic mirror. Otherwise, the shape of the reflected objects and the distance to them will be greatly distorted. In some defective models of car mirrors, a “double reflection” effect occurs. This may confuse the driver and lead to incorrect assessment traffic situation and making a wrong decision.

Driving with a panoramic car mirror takes some getting used to. It is especially important to learn how to correctly determine a safe distance.

The panoramic mirror is selected individually for each car model. When installing it, you need to pay attention to the following points:

• high headrests rear seats, wide rear pillars And spare wheel on the tailgate can block a large viewing area;
• poor choice of shape, size and installation location panoramic mirror may prevent the sun visors from opening.

Rearview mirror with built-in monitor

Rear view mirror with monitor

Installed inside the cabin on regular place car mirrors It is a monitor that can work as a regular mirror. Varies overall dimensions– from small to large (9 inches).

Connects to . Working together. This promotes the safest possible reversing. Simplifies the process of maneuvering in difficult situations. The display displays a picture, displays hints (information about the distance to the nearest obstacle), and indicates the dimensions of the vehicle.

More expensive car mirrors provide the possibility of touch control, installing a memory card, connecting a front camera or video recorder.

Setting the interior and side mirrors

1. Salon. Everything is very simple. Find the center point of the car mirror rear view. Align it with the center line of the rear window.
2. Lateral. Adjust the driver's seat to suit you. Lean to the left, almost touching the side window. Place the left mirror in such a position that you can see rear wing cars. When sitting normally, it should disappear from your field of vision. Lean to the right so that your head is in the central part of the cabin (between driver's seat and a chair front passenger). The rear fender should also be visible in the right mirror. To check the correct adjustment of the 3 car mirrors as a single rearview system, enlist the help of a passenger. Ask them to walk around the car slowly. At this moment, it is necessary to monitor his movements in the rearview mirrors. If a person disappears from one car mirror and immediately appears in another (with short pauses), then the number of “blind spots” is minimal. The side mirror is adjusted correctly.

Video: It’s better to see once than to read a hundred times - how to adjust the mirrors in a car and what a dead zone is

About additional options for side mirrors

Additional mirror for blind spot

1. Electric drive. Convenient system remote control glass mirrors, into the housings of which compact electric motors. They feature minimal energy consumption. The process of controlling the mirrors is carried out using buttons.
2. Turn signal repeaters. Provide additional security movement, more clearly warning other road users about the maneuvers being performed. They perform a decorative function, giving the car a stylish appearance. Installed from the factory or during the tuning process. Conventional turn indicators on the mirrors are used as standard halogen lamps. In premium cars, LEDs are installed in their place.
3. Additional small mirror. Built into a standard car side mirror to the right of the driver. Most often has a spherical shape. Improves visibility and reduces the number of “dead spots”. Is additional element security. Often installed on cars to train new drivers.
4. Decorative overlays. Made from ABS plastic, of stainless steel, chrome, carbon and other materials. They make the car more stylish and unusual, making it stand out from the general city traffic. They are an additional protective element for the main mirror body. Some trims are supplied with turn signal indicators. The installation process is carried out using fastening elements or special glue-sealant.
5. . The heating system operates using special heating elements. and coating the mirrors with condensate prevents the formation of ice. Saves the driver from the hassle of wiping them when there is strong humidity outside. Heating of car mirrors is carried out from the vehicle's on-board electrical network. Connection is made in several ways: parallel or separate (with a fuse, relay and switch).
6. . Lightly tinted side mirrors can protect the driver's eyes from reflection bright light headlights, strong - distort the color rendition, reduce the overall perception of what is happening on the road.

There are 3 different heating elements used for heating exterior car mirrors:

• resistance wire with insulation having heat-resistant properties;
• resistive element based on conductive paste. Applied by screen printing;
• heating element in the form of a film. At the same time it is a reflective layer.

About caring for mirrors

Car mirrors are integral elements safe traffic. Must be securely installed and adjusted correctly. But this is not enough for safe operation of the machine. Another important factor – proper care behind car mirrors. They must be kept clean, dust and dirt must be removed in a timely manner, and heavy icing must be prevented during winter operation.

For this purpose, special car wipes, detergents and antifreeze compounds are used. Are applied protective coatings, preventing the adhesion of dirt and effectively draining water. It is better to purchase them in specialized auto chemical stores.