Repair always begins with a diagnosis. If necessary, it is carried out on a special brake stand, allowing you to track the residual life of all components and assemblies of the brake system of the Hyundai i30 car.
And upon completion of most operations, it is necessary to pump the brakes by releasing air from the system.
Brake Fluid Replacement
The manufacturer recommends replacing brake fluid in a Hyundai AI 30 car at least once every 2 years. This is due to the fact that even if there is a sufficient level of it in the system, operation in an aggressive environment leads to the loss of basic properties.
Our masters will consistently merge and pump it out as if from brake cylinders, and from the brake barrel, they will fill in a new one, and then they will pump the brake system of the car and check it for leaks.
Repair and maintenance of calipers
The calipers themselves in most cases are almost eternal. They usually have to be replaced after an accident, for example, when the caliper bracket bursts or in the event of very strong wear produced by rust. In all other cases (and there are many of them), calipers are repaired on the Hyundai i30.
The caliper is removed from the car and disassembled. Available for sale as individual parts(pistons, gaskets, fittings), and complete assembly kits. The caliper itself is cleaned of rust, if necessary, machined on the machine and, after replacing the insides, is installed back.
For all types of repair work brake system car, replacement brake pads, discs, brake fluid, calipers, a repair warranty is provided. In stock wide choose original and not original spare parts. We at the Hyundai car service network are ready to make repairs on the same day and at affordable prices.
If available on working surface scuffing disk, deep scratches and other defects that increase pad wear and reduce braking efficiency, as well as in case of increased lateral runout disc causing vibration when braking, replace the disc.
The minimum allowable brake disc thickness is 8.4 mm. If the thickness of one of the discs is less than the specified value, replace both discs. When replacing brake discs be sure to replace the brake pads with a new set.
You will need a Phillips screwdriver.
1. Remove the wheel from the side of the disc being replaced.
2. Remove the caliper without disconnecting the hose from it (see "Replacing the caliper brake mechanism rear wheel").
3. Tie the caliper with wire to the spring to keep it from falling...
4. ... Remove the two screws securing the brake disc to the rear wheel hub ...
5. ... and remove the brake disc.
6. Install the brake disc in the reverse order of removal.
NOTE
Before installing the disc, carefully clean the mating surfaces of the hub ...
The state of the brake system directly affects traffic safety. If the brake pads or discs fail, the vehicle's handling will be reduced and this could lead to an accident.
To keep braking performance at high level, it is necessary to periodically diagnose the brakes and, if significant wear is found, immediately replace brake discs or pads. If you take care of your brakes and repair them in a timely manner, you will never have to worry about safety on the road.
Technology for replacing brake discs
Replacing the rear brake discs, like replacing the front ones, is a fairly simple, but time-consuming process that requires experience and training. Depending on the brand of the machine, the technology of work may differ slightly, however general rules brake repair for all cars are the same:
- Take off the wheel.
- Depress the piston and move the caliper to the side.
- Unscrew the disc from the hub.
- Dismantle the brake disc.
After installing the disk, collect what was dismantled, in reverse order. Replacing the front brake discs is almost the same as replacing the rear ones, except that the caliper may be positioned slightly differently.
Please note that the discs on the same axle must be changed at the same time, otherwise the difference in the thickness of the working surface will affect the braking performance. After the discs have been changed, the pads are checked, if they are worn out, they are also changed.
Signs of bad brake discs
The frequency of replacing discs and brake pads does not depend on mileage, but on wear. That is, better pads can last much longer than cheap duplicates.
Signs of bad brake discs:
- Increased stopping distance.
- Reduced brake fluid level.
- When braking, the car pulls to the side.
- Beating simultaneously in the brake pedal and steering wheel.
Disks become unusable if you brake often and sharply. Also bad for discs. sharp drops temperature - for example, if you sharply apply the brake in front of a puddle, and then drive into the water, the hot metal can be deformed.
Prices for replacing front and rear brake discs in Moscow
The cost of replacing brake discs is the sum of labor costs and the cost of spare parts. You can buy all the necessary parts for repairs of any complexity from us at an affordable price. Price repair work also low when compared with the average rates in the city. Call and we will call estimated cost the services you are interested in.
