According to the operating instructions, the Tomahawk 7010 alarm is not provided, but its implementation is carried out with the additional connection of the ESM 1 module. This also gives the car owner the opportunity to organize an additional engine blocking with a built-in control relay.

[ Hide ]

Specifications

Overview of the main parameters and properties of the Tomahawk 7010 car "signaling":

• current consumption with the ignition off - 16 mA;
• the frequency of the radio channel through which packet data is transmitted is 434 MHz;
• a type of modulation used to synchronize the antenna transceiver with the remote control - FM;
• operating range of the key fob (pager, communicator) - 1.2 km;
• the duration of the signals for controlling the central lock (CL) is from 0.8 to 30 seconds and is programmed by the user in accordance with the manual;
• using feedback to connect the remote control with the car alarm control unit;
• to power the overall optics, two outputs are used, designed for 7.5 A, sirens - 1.5 A, central locking - 15 A.

The use of Tomahawk 7010 is possible on passenger vehicles with an operating voltage of +12 volts in the on-board network.

Equipment

Description of parts and devices included in the delivery of the security system Tomahawk 7010:

1. The control module, equipped with a microprocessor, is made in a black plastic case with model marking.
2. Master pager, with built-in feedback system and display. The screen displays data on the state of the vehicle and protection.
3. An additional keychain that allows you to perform almost all functions. This device does not have a display.
4. Sensor for determining external influences and impacts on the car body. Incorrect setting or faulty state of the controller will result in false siren activation and alarm mode.
5. LED lamp. Designed to determine the state of the anti-theft complex.
6. Transceiver with antenna module and connection cable.
7. A set of wires for mounting and connecting the components of the security complex to the control unit and battery.
8. Service manual for the use and adjustment of the anti-theft installation.
9. Limit switch to protect the engine compartment or luggage compartment. This device is push-button.
10. Box.
11. Buyer's note. The document indicates the nuances regarding the maintenance of the product.
12. Warranty card.

The manufacturer did not provide a siren and “limit switches” for doors in the Tomahawk 7010 alarm package, so these items should be purchased additionally.

Channel "130" in the video briefly spoke about the configuration of anti-theft systems 7010.

Key Features

Description of the main functions and features of the Tomahawk 7010:

1. The complex is equipped with a signal anti-scanner. It is designed to protect transmitted pulses from being intercepted and scanned. The developer claims that hacking the alarm is impossible.
2. The presence of a non-volatile memory module in the control unit. This allows you to save information about the alarm when the power is turned off. Further activation of the battery will cause the system to return to its original state.
3. Using a two-level touch sensor shock. The device allows you to determine not only the physical effects on the body, but also the movement near the vehicle. All information is transmitted to the remote control with a screen.
4. Panic function. Its principle of operation is to activate the headlights of the car and alarms when receiving a command from the pager. The option helps to scare off possible intruders from the car.
5. Automatic re-arming. This function allows you to return the protection of the car if it is accidentally turned off.
6. Bypass non-working security zones. When armed, the alarm monitors the status of all elements connected to the control unit. Information about this is displayed on the key fob display.
7. "Auto search". Activation of the option leads to the blinking of the lights when receiving the appropriate command from the pager. This allows you to find a vehicle left in a large parking lot.
8. Determination of the battery discharge in the key fob. The status indication is displayed on the screen as a battery icon, similar to mobile phones. This allows the car owner to determine the failure of the battery in time and replace it.
9. Use of additional channels. They are designed to control such electrical equipment as power windows, sunroof, seat adjustment, folding mirrors. It is also possible to control the operation of the tailgate lock. The function is user-programmable.
10. Switching on the security mode on the car with the engine running.
11. Possibility of connection of additional sensors and regulators.
12. Two-step deactivation of protection. The user can set up protection mode control via the remote control and an individual password.
13. Possibility of remote shutdown of the shock regulator and additional devices. The user can deactivate only one zone of the sensors - warning, and leave the alarm zone.
14. Delay turning off the lights in the car. The user independently adjusts the interval at which the lighting will work for a certain time after the ignition is turned off and the security function is activated.
15. Blocking the car engine when arming. Activation and deactivation of the option is carried out by means of a relay with normally closed and open contacts. In one state, the device works, in the other it does not.
16. The built-in central locking (CZ) provides additional protection of the car.
17. Using a relay to connect car lighting devices.
18. The possibility of separate control of the central locking on a vehicle with a running engine.
19. The "Anti-robbery" function blocks the operation of the motor during a robbery attack on a car. The alarm automatically detects a power grab based on readings from the handbrake and pedal sensors. The engine stop is performed automatically after a gap that will allow the criminal to move away to a safe distance from the user. The time is user-configurable and can range from 30 to 60 seconds. This keeps the car owner safe.
20. Application of a personal code to gain access to the service mode and security functions.
21. Warning the owner of the car about open doors before driving.
22. Ability to use the stock steering horn to play alarms. The option is programmed at installation. The horn can be configured to work with or without a siren.

Advantages and disadvantages

The list of the main advantages of the system:

• application of a dialogue method of encryption of transmitted signals;
• advanced functionality at an affordable price for most consumers;
• understandable service manual for maintenance and connection in Russian.

In accordance with consumer reviews, the main disadvantage of the Tomahawk 7010 alarm is the rapid failure of the pager battery. When the system is first set up and options are programmed, discharging is much faster.

Differences between TZ-7010 and TW-7010

Alarms Tomahawk TZ-7010 and TW-7010 have the same functions, the essential difference between these models is only in the design of communicators.

Pagers for managing these systems have minor differences in terms of the form of execution. But these devices are interchangeable and can be used in similar systems without loss of functionality.

How to install Tomahawk 7010?

Alarm installation guide 7010:

1. Inside the cabin, a system control unit is discreetly installed. The device can be placed behind the instrument cluster, radio or under the control panel. Fixation is carried out on a flat surface using clamps or self-tapping screws. To eliminate the effects of vibration and moisture, the module can be wrapped with foam rubber and cellophane.
2. A siren is placed under the hood if it was purchased additionally. For fixing, a bracket is used, which must be screwed to the car body. The siren is mounted away from the cylinder block and other metal surfaces and parts adjacent to the body.
3. A service mode button "Override" is installed under the instrument panel. To hide this element, you can additionally wrap it with tape in the standard color.
4. A transceiver with an antenna adapter is placed on the windshield. It is recommended to place it away from electronic circuits and metal parts. Do not install the device in the upper part of the glass if it has a tint film applied to it.
5. A limit switch is installed on the hood. The wire from it must be laid to the control module through the technological hole that separates the passenger compartment from the engine compartment. It is not allowed to install the device in a place where a drain passes.
6. The shock sensor is located in the central part of the car body. For its fixation, a flat metal surface is used without gaskets made of plastic or rubber.
7. After installation, all signaling components are connected to the control unit. Wire laying should not be carried out near electronic devices and power circuits of spark plugs.

Connection map for the main 14-pin connector

The connection of the main block of the system control unit must be carried out in accordance with the diagram:

Color	Description
Red	The power supply of the car alarm must be connected directly to the positive terminal of the battery. The electrical circuit must be protected by a 15 amp fuse.
black green	Positive output of contacts on the rotary optics relay
Black	Negative clip. It must be connected to the car body or the negative terminal of the battery directly. When grounding, the most durable contact should be ensured.
yellow green	Positive relay output of overall or rotary optics, the circuit must be equipped with a 7.5 amp fuse
Blue	Negative contact for connecting courtesy lights or power window controls
Yellow	Positive input of the ignition switch
black and yellow	Negative output for connecting the relay blocking the starter mechanism
Grey	Positive terminal for connecting to a siren or steering horn
red yellow	Not used
black and yellow	Negative pin to implement an additional channel
Red blue	Positive contact for connecting door lock switches
black blue	minus triggers
white-orange	"Limit switch" of the luggage compartment
Grey-orange	Hood limit switch negative terminal

User manual

According to the operating instructions, before using the Tomahawk 7010 alarm, you must make sure that the system is connected correctly. You should activate the security mode and make sure that the door locks are locked.

Key fob control

To control the key fob, you need to install a working battery in the device. The battery is inserted into the compartment located under the rear protective cover of the immobilizer.

The Tomahawk 7010 alarm control unit can work with no more than four key fobs. When new communicators are added, information about old remotes is erased from the microprocessor memory.

How to program a key fob?

Binding a new remote control, in accordance with the operating instructions for the Tomahawk 7010 alarm:

1. When the ignition is off, the key in the lock is moved to the “Off” position.
2. The button to enter the service mode is “clicked” seven times. The driver at this moment must be in the car in his place.
3. The key in the lock turns to turn on the ignition. The siren or steering horn will sound seven times, indicating that the system has entered the remote programming menu.
4. On the main communicator, keys 3 and 4 are pressed simultaneously. The controls are held until the sound signals are played. This indicates that the information about the pager has been successfully written into the memory of the microprocessor device.
5. To exit the programming menu, do not take any binding action for 60 seconds. The alarm will automatically return to its original state.

The steps to turn off and on the ignition, press the service button and bind are repeated for each device.

Designation of symbols and buttons on the key fob

Icon indication on the main pager screen:

Primary communicator display

Item Description:

1. The option to block keys on the device is enabled.
2. Hourly auto start mode is activated.
3. Blocking the power unit.
4. The automatic arming function is enabled.
5. The vehicle's ignition system is activated.
6. Started engine.
7. The luggage compartment lock is open.
8. The anti-robbery attack mode on the vehicle is enabled.
9. Alarm option as a result of a strong blow to the body.
10. Car service.
11. Shock sensor warning zone.
12. Disable the sensitivity controller.
13. Indication of the connection of the pager with the microprocessor unit.
14. Vehicle security mode with enabled or disabled confirmation signals.
15. The door locks of the machine are locked or open.
16. Icon to disable the main zone of the sensitivity controller.
17. Charging the battery in the key fob.

Correspondence of keys on communicators Tomahawk 7010

autorun

Preparing the car for setting up the remote start option is done as follows:

1. On a car with the engine running, the transmission selector is put into neutral or "Parking" mode.
2. The hand brake lever is raised.
3. The key is pulled out of the ignition lock. The motor remains running.
4. The user exits the vehicle and locks all doors. The power unit should randomly stop.

How to set up autorun?

On vehicles with an automatic transmission, the setting is as follows:

1. Button 2 is pressed and held on the pager. This control element must be released after the melodious signal is played by the remote control.
2. When using an additional key fob, the LED will change its color from red to green. At this moment or after the melody, the user must briefly press button 2. The power unit of the machine will start, the pager will play a signal, and the headlights of the car will flash.
3. The engine will shut down automatically after a user-programmed time. After starting the engine, the communicator screen will display an indicator in the form of a vehicle with smoke from the muffler.

To start the power unit on a machine with a manual transmission, the following steps are performed:

1. Press and hold button 1 on the pager.
2. The control element is released at the moment of playing a melodic signal. When using a spare communicator, the LED will change color.
3. The first key is "clicked" again.

User Evgeny Vakshin spoke about the features of setting the autorun function on Tomahawk anti-theft systems.

Guard mode

Protective function control features:

1. To turn on, use button 1. All door locks will close, the headlights of the car will blink and the siren will sound. Disabling the security mode is done by pressing the second key.
2. Control 4 is used to activate protection without sound notifications. In case of a siren activation, information about this will be displayed only on the remote control screen.
3. If you want to activate the security on a car with the engine running, the engine must be started in advance. The driver needs to lock all the locks, and then "click" on the first key. Then, within three seconds, the user must press the same button again. When the guard is turned on, the side lights will blink and the siren will sound.

If the pager breaks down, protection is activated using the service key:

1. The door of the car is opened with a key, as a result of which the siren will work. The ignition is switched on.
2. The button to enter the service mode is pressed three times.
3. The key in the lock is moved to the "Off" position. The siren and headlights of the car will work.
4. After 20 seconds, the protection will be activated. The user must have time to get out of the car and lock all the doors during this time.

Entering and changing the password

Initially, the alarm is assigned code 11.

To enter it when the system is turned off, the following actions are performed:

1. The car door opens, the ignition is activated.
2. The button for entering the service mode is pressed once (if the standard password is used).
3. The key is scrolled to the "ACC" position. The "Override" key is "clicked" again (this is the second digit 1 of the password).
4. The ignition is turned off.

To change the individual code of Tomahawk 7010, the following steps are performed:

1. After turning off the ignition in the car, the button to enter the service mode is pressed 4 times.
2. The key in the lock scrolls to the "ACC" position. The siren of the anti-theft system plays 4 beeps.
3. The "Override" key is pressed once, as a result of which the alarm will enter the code setting mode. To enter a password, characters from 1 to 4 can be used, they are indicated by buttons in accordance with their numbers. If the first digit of the password is accepted, the siren will sound.
4. To specify the next character, you need to “click” once on the service key. Input actions are similar.

Download free installation and operating instructions in PDF format

You can download the technical documentation for the installation and configuration of the Tomahawk 7010 security complex using the links:

Errors in the operation of the device and their elimination

Overview of malfunctions and malfunctions that may occur in the operation of the Tomahawk 7010:

1. The security system does not respond to sending commands from the remote control. The user must diagnose the power supply in the device. If the battery needs to be replaced, the polarity must be taken into account during installation. After dismantling the element, press button 5.
2. If there is no response to commands, the cause of the problem may be damage to the board or contact elements on the keys of the communicator. For repair, the user will need to disassemble the device by unscrewing the bolts on its body and check the circuit. If traces of moisture are visible on it, then the communicator must be dried in a warm place, but not near a household stove or in the sun. Failed contacts must be resoldered or stripped if the problem is their oxidation. Use a dry brush or cloth to remove dust and debris from the housing.
3. Incorrect alarm operation and lack of response may result in damage to the cables. If the insulation layer is worn or broken, the system does not close all the doors or does not respond at all to the pager command. A multimeter is used to diagnose the integrity of electrical circuits. When checking, you must first assess the condition of the lines that are laid in the area of ​​moving nodes. When laying new wires, it is recommended to wrap them with electrical tape to ensure maximum reliability in the future.
4. The cause of the malfunction may be poor contact of one of the alarm blocks with the control unit. It is necessary to diagnose the connectors for connecting the microprocessor, the transceiver, as well as push-button switches. Contact elements may be clogged or oxidized, cleaning them will be required to fix the problem. If the plug itself fails, it must be replaced.
5. A large number of false alarms may be due to incorrect shock control sensitivity settings. To change this parameter, special control devices are used, located directly on the sensor.
6. If it was not possible to find the reason for the incorrect operation of the alarm, then it may be a malfunction of the microprocessor. The device could fail due to moisture ingress. Troubleshooting steps are the same as for a pager. If visual diagnostics did not allow to determine the problem, then we can conclude that it is a software malfunction. To fix it, you will need to flash the control unit or repair it.

How much does Tomahawk 7010 cost?

You can buy model 7010 at this price:

Video

Sergey Yashchenko in his video showed the process of hacking the Tomahawk anti-theft system using a code grabber.

USER'S MANUAL AND INSTALLATION INSTRUCTION CAR ALARM TOMAHAWK TW-7010 Look for new versions of instructions on the website http://intorg.ru TOMAHAWK TW-7010 CONTENTS: OPERATION MANUAL. I. II. III. IV. V. Main functions of the system. LCD display indication. Remote control key fobs. Functions performed using the key fob. How to use the security complex: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. Arming. Quiet arming. Disabling the shock sensor and additional sensor. Disabling security mode. Two-step disabling of the security mode. Engine guard. Automatic arming. Automatic re-arming. Security mode. immobilizer mode. Safe driving feature. Central locking control while driving. Car search. Panic function. Anti Hijack. Remote Anti-Hijack. Valet mode. Protection against false positives. Remote status polling. Remote trunk release. Remote shutdown of the siren. Additional channel management. Emergency arming/disarming. Personal code (PIN code). Programming a new PIN code. Programming new key fobs. Information about programmed key fobs. Information about the health of the sensors. Display of information on the LCD key fob. The functionality of the key fob-pager. LED indication. The procedure for replacing the battery in a key fob with an LCD display. Function programming mode. Return to factory settings. VI. Programming table. Description of programmable functions 3 4 7 8 9 9 9 9 9 10 10 10 11 11 11 12 12 12 12 12 13 13 14 14 14 15 15 15 16 16 18 18 18 19 18 20 20 20 21 22 23 More about car alarm TOMAHAWK TW- 7010 on the site http://intorg.ru 1 TOMAHAWK TW-7010 INSTALLATION GUIDE. I. II. III. IV. V. VI. Basic principles of installation. Selecting the location of the main blocks. System connection. Scheme. Technical data. Equipment. 25 25 26 28 35 36 You have purchased a professional anti-theft alarm. This security complex is made with the greatest care, it uses the latest achievements and technologies. The alarm system will provide your car with reliable protection against encroachments of thieves and robbers, thanks to the latest technologies. You will be able to fully control the situation inside and next to your "favorite". The wide service functions of the security complex will reveal new possibilities of the car to you. 2 More information about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru TOMAHAWK TW-7010 OPERATION MANUAL I. Main functions of the system. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. Antigrabber. Antiscanner. Non-volatile memory allows the system to retain its state in the event of a temporary power outage. Dual level shock sensor. Two-level additional sensor. Panic mode. Automatic re-arming. Valet mode. Bypassing the faulty zone. Protection against false positives. Programmable key fobs. Car search. Low battery indication. Programmable additional control channel. Guard mode with the engine running. Disabling the siren from the key fob. Programmable pulse of the central lock. Two-step disabling of the security mode. Temporary shutdown of the shock sensor and additional sensor. Cabin lighting delay function. Remote status polling. Remote trunk opening (option). Engine blocking (programmable NC / NO). Built-in parking light relay (two channels). Built-in central locking. Central locking control with the engine running. Built-in immobilizer. Graphic indication of all triggered triggers and system status on a key fob with an LCD display. Polite backlight function (option). Anti-Hijack mode - protection against robbery. Individual PIN code. Memory of system operation. Door open warning function while driving. Increased range of key fob with LCD up to 1200m. (depending on external conditions). Possibility to connect a regular horn (programmable). Possibility to control the comfort system. Information about programmed key fobs. Display of system status changes on all programmed remote controls with LCD display. Built-in clock (LCD key fob). Built-in timer (LCD keychain). Built-in alarm clock (LCD keychain). The function of blocking the buttons of the key fob-pager. More information about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 3 TOMAHAWK TW-7010 II. LCD display indication. 1-1 Z Z Z HIJACK PASS AM PM 1 4 1. - protection mode indication. 2. - indication of the "quiet guard" mode. 3. - indication of the closed central lock. 4. -indication of an open central lock. 5. - indication of the open door(s). 6. - indication of an open hood. 7. - indication of an open trunk. 9. - indication of operation of the key fob-pager transmitter. More information about the car alarm TOMAHAWK TW-7010 on the site http://intorg.ru TOMAHAWK TW-7010 10. - weak impact indication. 11. - indication of a strong blow. PASS 12. - indication of disabling the warning zone of the shock sensor. PASS 13. 14. 15. - indication of disabling the main zone of the shock sensor. HIJACK 1-1 Z Z Z - indication of the “Anti-hijack” mode. - indication of the “Valet” mode 16. - indication of the handbrake off 17. - indication of the battery charge level. 18. - indication of the switched on ignition. 19. - indication of blocking the buttons of the key fob-pager. 20. - indication of the included immobilizer. 21. - indication of the activated automatic arming mode. 22. - indication of the included timer. More information about the car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 5 TOMAHAWK TW-7010 23. - indication of the alarm clock on. AM 24. PM 6 hours. More information about car alarm TOMAHAWK TW-7010 on the website http://intorg.ru TOMAHAWK TW-7010 III. Remote control key fobs. The security complex can be equipped with two types of key fobs. Key fob with LCD display displays information about the state of the car using icons-icons. Keychain standard type waterproof (spare). F LCD Fig. 2 LED Fig. 3 The remote control (Fig. 2) is a miniature transceiver powered by a AAA-1.5V battery, the battery life depends on the operating conditions. A special indication is provided to control the battery charge level (see page 5). Don't forget to change the battery in advance! The key fob has five control buttons: kn. , book. , book. , book. , book. and liquid crystal display. When one button or a combination of buttons is pressed, the built-in processor generates an encoded command for its execution by the main unit. Each next code is not similar to the previous one (antigrabber). After executing the command, the main unit sends a message about the execution to all key fobs programmed into memory with an LCD display. Information about the state of the car is displayed on the display in the form of “icon” pictures. More information about the car alarm TOMAHAWK TW-7010 on the website http://intorg.ru 7 TOMAHAWK TW-7010 IV. Functions performed using the key fob. Combination of buttons Function x2 x2 2s Note Arming, closing the central lock Ignition off Disarming, opening the central lock Ignition off Closing the central lock Ignition on Opening the central lock Ignition on Disabling the shock sensor Arming mode Disabling the additional sensor. Security mode VALET mode on/off Disarmed On/Off sirens. Ignition off. Engine guard. Ignition on Checking the system status. x2 Search for a car. 2s + + Trunk opening. 2s Panic. Ignition off. 2s Remote Anti-Hijack incl. Ignition on Remote Anti-Hijack off + 2s Immobilizer on/off 2s Auto arm on/off - Press x2 at the same time - Press 2 times within a second 2s - Hold until the key fob beeps (or the LED color on the additional key fob changes to green) TW-7010 V. How to use the security system. 1. Arming. To turn on the security mode, press the button once. . The lights will flash once and the siren will sound one "CHIRP" (unless the siren is disabled). The system will close the central lock. The LED will blink uniformly. LCD display indication: Attention! If at the moment of arming any trigger is active (for example, the door is open), the system will give 4 siren signals and 4 flashes of parking lights. 2. Silent arming At night, you have the opportunity to arm the system without sound notification. In this case, the siren will be disabled. To use this feature, press the button. once. The system will close the central lock, the LED will blink evenly, the lights will flash once. LCD display indication: Attention! The sound notification of the siren is disabled, but all information is displayed on the keyfob display. 3. Disabling the shock sensor and additional sensor. If you leave someone inside a guarded vehicle or the vehicle is parked on the side of a busy road, it is possible to temporarily disable the shock sensor. To turn off the warning zone of the shock sensor after the armed mode is turned on, press the button 2 times within 1 second. Subsequent pressing of this button twice will turn off the main zone of the sensor. Repeat this procedure to turn on the shock sensor. To turn off the warning zone of the additional sensor, press the button. 2 times within 1 sec. Pressing twice again will turn off the main zone of the additional sensor. To enable an additional sensor, repeat this procedure. PASS PASS LCD display indication: or 4. Disarming. To disable the security mode, press the button. The doors will open, More information about the car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 9 TOMAHAWK TW-7010 siren will give 2 "CHIRPS", side lights will flash 2 times. The courtesy interior lighting will turn on (optional). LCD display indication: Attention! If, when disarming, the siren and key fob with LCD display emit 4 "CHIRPS", it means that some sensor was triggered. 5. Two-step disarming. If the security complex is in alarm mode, i.e. the siren works, the parking lights flash, then the first press of the book. returns the system to the "rest" state, and only a second press will disarm the system. 6. Security with the engine running. You have the opportunity to activate the security mode with the engine running. To do this, you must: 1) Start the engine. 2) Get out of the car, close the doors, hood, trunk. 3) Press the book. , the door locks will close. 4) Within 3 sec. after completing step 3, press the button. again, the siren will sound 1 "CHIRP", the parking lights will flash 1 time. LCD display indication: Attention! In this mode, the shock sensor and the additional sensor are disabled. To disable the guard with the engine running, press the button. open, the security mode will be disabled. , doors LCD display indication: 7. Automatic arming. This function is turned on and off by holding the button. until the key fob-pager beeps (or the color of the LED on the additional key fob changes to green) and then pressing the button. . LCD display indication: Attention! 10 Door locking during automatic arming is programmed (see the programming table). More about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru TOMAHAWK TW-7010 8. Automatic re-arming. This feature is programmable. If this function is programmed and you disarmed, or it happened accidentally, then within 30 seconds the system will automatically return to armed mode, provided that you did not open the doors and did not turn on the ignition. 9. Security mode. When armed, the alarm monitors all zones and trigger sensors. In case of operation, the alarm system is activated. Depending on the protection zone, the system has different alarm signals: a) The alarm is caused by the activation of the warning zone of the shock sensor or the warning zone of the additional sensor. The siren will sound 3 "CHIRPS" and the parking lights will flash 6 times. LCD display indication: b) The alarm is caused by the activation of the main zone of the shock sensor or the main zone of the additional sensor. The siren will work simultaneously with the parking lights for 30 seconds. LCD display indication: c) The alarm is caused by the operation of the main zones: doors, hood, trunk, ignition. The siren will work simultaneously with the parking lights for 30 seconds. The LCD display will show the triggered. 10. Immobilizer mode. This function is activated and deactivated by holding the button. until the key fob-pager beeps (or the color of the LED on the additional key fob changes to green) and then pressing the button. . If the function is activated, then ~ 30 seconds after the ignition is turned off, it will automatically turn on and block the engine. The activation of the immobilizer will be signaled by the system LED when the ignition is on. LCD display indication: To disable the immobilizer, press the button. turn off, the LED will turn off. Attention! , blocking the engine Immobilizer emergency shutdown: 1. Turn off the ignition 2. Press the Override button 1 time. More about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 11 TOMAHAWK TW-7010 11. Safe driving function. This function is programmable (see programming table). If the function is activated, the doors will automatically lock when the ignition is switched on. (The system provides 4 options for setting this function, see page 21 section 2) Attention! If the vehicle doors are opened within 10 seconds after the ignition is switched on, this function is automatically deactivated. 12. Central locking control while driving. When the car's ignition is on, you can control the car's central locking by pressing the button. for closing doors and books. to open doors. LCD display indication: - closed - open 13. Car search. At night, you can use the "Search for a car" function. For this you need to press the button. key fob 2 times within 1 second. The parking lights will flash simultaneously with the "CHIRPS" of the siren 6 times. Attention! The LCD display will update the vehicle status information. 14. Panic function. You can use this feature to attract the attention of others. With the ignition off, press and hold the button. and, the siren will emit 3 long beeps, the parking lights will flash 3 times, the doors will close, the system will arm. Attention! The LCD display will update the vehicle status information. 15. Anti Hijack. To activate this function with the engine running, press the "OVERRIDE" button 1 time, after opening and then closing the door, the function will be activated. The side lights will flash 1 time, the LED will blink. For the operation steps and the procedure for disabling the Anti-Hijack mode, see paragraph 16 "Remote Anti-Hijack" LCD display indication: 12 HIJACK More information about the car alarm TOMAHAWK TW-7010 on the website http://intorg.ru TOMAHAWK TW-7010 16. Remote Anti-Hijack. The function is used to return the car in the event of a violent seizure. To activate this function, when the ignition is on, press and hold two buttons and the key fob at the same time. The parking lights will flash 1 time, the system LED will flash. Remote Anti-Hijack has 3 stages of operation: Stage I: First 30 sec. after activating the Anti-Hijack mode, the system does not manifest itself in any way, the security complex allows the attacker to move away from you somewhat. Attention! At the first stage, it is possible to turn off the mode from the key fob, for this you need to press the button. or hold the "OVERRIDE" button for 3 seconds. Stage II: Next 30 sec. the siren emits warning "CHIRPS", side lights flash. Stage III: The final stage occurs after about 60 seconds. after activating the Anti-Hijack mode. The siren will turn on, the engine will be blocked. Attention! To disable the Anti-Hijack mode at stages II and III: 1. Turn on the ignition. 2. Press and hold the button. OVERRIDE for 3 sec. (the siren will emit 3 “CHIRPS”) 3. Turn off the ignition. 4. Anti-hijack mode will be disabled. The system will remain armed. If a PIN code is programmed, the Anti-hijack mode can only be deactivated by entering the PIN code. LCD display indication: HIJACK 17. Valet mode. Valet mode is used by the car owner if the car is transferred to third parties, for example, for maintenance. After activating this mode, the system can only perform service functions, such as controlling an additional channel or central lock. Turning the Valet mode on and off is done when the protection is off by holding the button. until the key fob-pager beeps (or the color of the LED on the additional key fob changes to green) and then pressing the button. , or by holding the book. "OVERRIDE" for 3 seconds, with the ignition on. Activation of the Valet mode will be confirmed More about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 13 TOMAHAWK TW-7010 4 flashes of parking lights and 4 "CHIRPS" of the siren, the LED will be constantly on. LCD display indication: 1-1 Z Z Z 18. Protection against false positives. The Tomahawk TW-7010 security complex belongs to highly intelligent car security devices, so the system uses a complex, multi-level algorithm for protecting against false positives. First level. At the moment of arming, the main unit tests all security zones, if any sensor is found to be defective, the system automatically turns it off and informs you about it using 4 "CHIRPs" of the siren. LCD display indication: icon of the corresponding trigger. Second level. During the armed mode, the system analyzes the operation of the sensors, if the shock sensor or an additional sensor has worked 8 times in a row, it will be disabled. 19. Remote interrogation of the state To perform a remote interrogation of the state of the vehicle, press the button. The parking lights will flash 3 times, the key fob pager will display the state of the vehicle. Attention. If after pressing the (or any other button) within 3 seconds there is no confirmation of the execution of the command and the keyfob pager emits 1 “BEEP”, which means the vehicle is outside the coverage area of ​​the keyfob pager transmitter. 20. Remote unlocking of the trunk (additional channel). Many vehicles require the installation of additional equipment to implement this function. If this option is enabled, then to unlock the trunk, press and hold the button. key fob until the key fob-pager beeps (or the color of the LED on the additional key fob changes to green) and then pressing the button. . The execution of the command will be accompanied by 3 flashes of parking lights and "CHIRPS" of the siren. Attention 14 If the system was armed at the moment of unlocking the trunk, the shock sensor and the trunk trigger will be disabled until the trunk is closed. More about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru TOMAHAWK TW-7010 LCD display indication: 21. Remote siren shutdown. In many countries, the use of car alarm sirens at night is prohibited (for example, in Moscow after 2300), therefore, the security complex provides for turning off the siren from the key fob. To do this, it is necessary that the system is armed, then press the button. . LCD display indication: In this case, the system will be fully operational, except for the sound notification by the siren. All information will be displayed on the key fob LCD display. The siren is turned on by pressing the button once. LCD display indication: 22. Additional channel control. An additional channel makes it possible to use standard car devices, open the trunk, control power windows, turn on the illumination of the way at night with car headlights, etc. To control an additional channel, you must press and hold the key fob button until the key fob-pager beeps (or the color of the LED on the additional key fob changes to green) and then press the button. , the parking lights will flash 2 times to confirm the command. Activation time add. channel is programmed (see programming table). Attention! The LCD display will update the system status information. 23. Emergency setting / disarming. If your key fob does not function or is lost, you have the ability to enable or disable the armed mode using the OVERRIDE button. To do this: 1. Emergency arming: 1) Open the door and turn on the ignition. 2) Press the button. OVERRIDE 3 times. 3) Turn off the ignition (the siren will emit 1 "CHIRP", the parking lights will flash 1 time). 4) 20 seconds later, the system will arm without locking the doors. Attention! If you have used the emergency arming, the system will include a 20-second delay in the alarm mode when triggered, thereby giving you the opportunity to use the emergency disarming. without turning on the alarm mode. 2. Emergency disarming: 1) Open the door and turn on the ignition. 2) Press the button. OVERRIDE 3 times. 3) Turn off the ignition (the siren will emit 2 "CHIRPS", the parking lights will flash 2 times). 4) Armed mode will be disabled immediately. Attention! If you have programmed a personal PIN code, emergency disarming can only be done using this PIN code. 24. Personal code (PIN code). This code (if programmed) allows the owner to disable the security mode without a key fob, as well as disable the Anti-Hijack mode at stages II and III. The PIN code consists of two digits. Attention! Factory setting of PIN code 1:1 1st digit 1(x) 2nd digit 1(y) Disable security mode using PIN code. If your key fob is not functioning, or the system is in stage II or III of the Anti-Hijack mode, then you can disable the security mode using the PIN code. To do this: 1. Open the door and turn on the ignition. 2. Press the "OVERRIDE" button a number of times equal to X (the first digit of the PIN code). 3. Turn off the ignition. 4. Switch on the ignition again. 5. Press the "OVERRIDE" button a number of times equal to Y (the second digit of the PIN code). 6. Turn off the ignition. If the PIN code value is entered correctly, the armed mode will be disabled. Attention! Repeat the procedure in case of unsuccessful PIN code entry. 25. Programming a new PIN code. Attention! 16 Programming a new PIN code is only possible if ”Emergency shutdown of the system using More information about car alarm TOMAHAWK TW-7010 on the website http://intorg.ru TOMAHAWK TW-7010 PIN code” is programmed (see “Programming table”) To change the PIN code necessary: ​​1. Switch off the ignition. 2. Press the "OVERRIDE" button 4 times. 3. Turn on the ignition, the siren will emit 4 "CHIRPS". 4. Press the "OVERRIDE" button 1 time to turn on the PIN code programming mode. 5. Using a valid key fob, enter a new value for the first digit of the PIN code. Digit value Attention! Corresponding button 1 Press the button 2 Press the button 3 Press the button 4 Press the button The siren by the number of "CHIRPS" will confirm the new value of the 1st digit of the PIN code. 6. Press the OVERRIDE button 1 time to enter the programming mode of the 2nd digit of the PIN code. 7. Using a valid key fob, enter a new value for the second digit of the PIN code. Meaning of the digit Corresponding button 1 Press the button 2 Press the button 3 Press the button 4 Press the button Attention! The siren will confirm the new value of the 2nd digit of the PIN code by the number of "CHIRPs". Attention! We recommend writing down the new PIN code value. More about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 17 TOMAHAWK TW-7010 26. Programming new key fobs. Up to 4 key fobs can be written to the memory of the main unit, for this it is necessary: ​​1. Turn off the ignition. 2. Press the OVERRIDE button 7 times. 3. Turn on the ignition. The siren will emit 7 "CHIRPS" confirming entry into the keyfob programming mode. 4. Press and hold simultaneously the buttons and the new key fob for 1 second. The CHIRPami system will confirm the entry of a new key fob into memory (1 CHIRP for the first, 2 CHIRPs for the second, 3 CHIRPs for the third and 4 CHIRPs for the fourth). After that, perform this operation with the next key fob (if necessary). Attention! All lost key fobs will be erased from the system memory, so the programming procedure must be subjected to all key fobs that you are going to use in the future. Attention! If within 6 seconds no steps were taken to program the keyfobs, then the programming mode will automatically turn off. 27. Information about programmed key fobs. For security purposes, the Tomahawk TW-7010 security complex has introduced the function of viewing the number of programmed key fobs. To display this information: 1. Turn on the ignition. 2. Press the button. key fob. 3. The number of LED flashes will indicate the number of key fobs already programmed into the system. 28. Information about the performance of sensors. To test the functionality of the sensors, turn on the ignition and activate the sensor whose performance you want to test (for example, open the door). If the sensor is working properly, the system LED will begin to blink slowly, and go out when the door is closed, indicating that the sensor is working. 29. Display of information on the LCD key fob. This security complex is equipped with a new notification system, so information about the execution of a command or a change in the status of the system will be displayed on the LCD displays of all key fobs programmed into the system's memory that are in the system's coverage area. 18 More about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru TOMAHAWK TW-7010 30. Functionality of key fob-pager. Used buttons Functions performed F Turn on the backlight F + F Turn on the lock of the key fob-pager buttons + F Turn off the lock of the key fob-pager buttons hold Notes Automatically turns off after 2 seconds Indication: Clock setting mode, alarm clock, timer Clock setting mode - clock F 1 time Setting mode hours - minutes F 2 times Alarm setting mode - hours F 3 times Alarm setting mode - minutes F 4 times Alarm setting mode - on/off F 5 times Timer setting mode - hours F 6 times Timer setting mode - minutes F 7 times Setting mode timer - on / off - translation forward - translation back - on. - off - translation forward - translation back - incl. More information about the car alarm TOMAHAWK TW-7010 on the site http://intorg.ru - off. 19 TOMAHAWK TW-7010 31. LED indication. The system LED is multifunctional. Using the LED signals, you can determine what state the security system is currently in according to the table: Mode Security mode Immobilizer mode VALET mode 1st and 2nd stage Anti-Hijack Ignition off Ignition on * * * * * * * * * * * Steady on Steady on * * * * * * * * * * * 32. How to replace the battery in the key fob with display. LCD Keychain with LCD display has a battery level indicator (type AAA, 1.5V). If the indicator shows the lowest level of charge, then you need to urgently replace the battery. To replace the battery: 1. Open the protective cover on the back of the key fob. 2. Remove the old battery. 3. Press the key fob button. 4. Install a new battery, observing the polarity (type AAA, 1.5V). 5. Close the protective cover. 6. Press the key fob button, the display will show the system status. 33. Function programming mode. To enter the programming mode, do the following: 1. Turn off the ignition. 2. Press the “OVERRIDE” button 5 times. 3. Turn on the ignition (confirmation of entering the programming mode - 5 “CHIRPs” of the siren). Use the “OVERRIDE” button to select the desired function. Each press - transition to the next function The system will indicate the selected function with the "CHIRP" of the siren: Short "CHIRP" - 1 Long "CHIRP" - 5 EXAMPLE: 7 presses of the "OVERRIDE" button - 1 long "CHIRP" and 2 short presses - 20 selected More about car alarms TOMAHAWK TW-7010 on the site http://intorg.ru TOMAHAWK TW-7010 function 7. Refer to the programming table for function numbers and descriptions. 34. Return to factory settings. To return to the factory settings of programmable functions: 1. Switch off the ignition. 2. Press the “OVERRIDE” button 10 times. 3. Turn on the ignition (confirmation -10 “CHIRPS” of the siren). 4. Press the “OVERRIDE” button 1 time (confirmation 1 "CHIRP" of the siren). 5. Press the button. key fob. More about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 21 22 Polite illumination or window closing (blue wire) Auto-arming Siren or horn Additional channel pulse duration (sec.) Type of engine blocking 6 times 7 times 8 times 9 times 10 times Factory settings are underlined in the table. Emergency shutdown of the system via PIN code 5 times NC 0.8 Siren On Courtesy backlight Off Off 3 times Locking doors during automatic arming Var. 1 Cabin lighting delay or arming delay 4 times Safe driving function 2 times Open: 0.8 Close: 0.8 Button Pulse length for opening / closing the central lock (sec.) Function 1 time Number of button presses. OVERRIDE HP 10 Var. 2 Off Courtesy backlight On On Var. 2 Vari. 2 Open: 3.6 Close: 3.6 VI button. Programming table HP 30 Horn Off Closing windows On On Var. 3 Vari. 3 Open: 2 x 0.8 Close: 0.8 NO button On/Off Klaxon off. Closing windows On On Var. 4 Off Var. 4 Button TOMAHAWK TW-7010 More details about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru TOMAHAWK TW-7010 Description of programmable functions of the system. 1. Central lock activation pulse length: 1) Closing pulse - 0.8 sec, opening pulse - 0.8 sec 2) Closing pulse - 3.6 sec, opening pulse - 3.6 sec 3) Closing pulse - 0 .8 sec., opening pulse - double 0.8 sec. 4) Closing impulse - 30 sec., opening impulse - 0.8 sec. 2. Safe driving function: 1) The doors close when the ignition is turned on, open when the ignition is turned off 2) The doors close after 10 seconds. after the ignition is turned on, open when the ignition is turned off 3) Doors do not close when the ignition is turned on, open when the ignition is turned off 4) Doors do not close when the ignition is turned on, and do not open when the ignition is turned off illumination switched on 2) Cabin lighting delay accounting switched off 3) Arming delay 30 sec. 4) Arming delay 45 sec. 4. Locking doors during automatic arming: 1) Doors do not close 2) Doors close 3) Doors close 4) Doors close system shutdown with PIN code only 3) System emergency shutdown with PIN code only 4) System emergency shutdown with PIN code only 6. Polite light or window closing (blue wire): 1) Polite light. Pulse duration 20 sec. appears when disarming 2) Polite illumination. Pulse duration 30 sec. appears when disarming 3) Closing windows. Pulse duration 20 sec. appears when arming More about car alarm TOMAHAWK TW-7010 on the website http://intorg.ru 23 TOMAHAWK TW-7010 4) Closing windows. A 30 second pulse appears when arming 7. Auto-arming: 1) Auto-arming enabled 2) Auto-arming disabled 3) Auto-arming disabled 4) Auto-arming disabled 8. Siren or klaxon: 1) Siren 2) Siren on. when arming, off. when disarming 3) Klaxon 4) Klaxon 9. Additional channel pulse duration (sec.) 1) 0.8 2) 10 3) 30 4) On/off. 10. Type of engine blocking: 1) Normally closed 2) Normally open 3) Normally open 4) Normally open I. Basic principles of installation. The Tomahawk TW-7010 security complex has a classic connection scheme. First of all, before starting the installation, turn off the vehicle's on-board power supply (disconnect the "-" battery terminal). To select the installation locations for security system units, be guided by the following principles: - Secrecy of the installation. - Absence of sources of heat and moisture emission near the blocks. - Provide a minimum influence on each other of standard electronics and signaling units. Attention! The transmitter antenna must be installed away from the signaling and vehicle control units. Try to minimize the length of the wires when installing. II. Selecting the location of the main units 1. The electronic alarm control unit is installed inside the passenger compartment of the vehicle. The receiving-transmitting "RF" antenna of the system unit, in order to obtain the maximum range of action, must be placed as high as possible, not in contact with metal objects, electrical wiring harnesses. 2. The siren is installed in the engine compartment, in an inaccessible place, if you use a stand-alone siren, provide access to the service key well. The siren must be installed with the horn down to prevent moisture from entering. It is better to plan the wire connections inside the cabin for less oxidation. 3. All high current circuits (power supply, parking lights, central locking, etc.) must be protected by fuses of the appropriate rating. 4. Triggers of the hood, trunk crash into places protected from moisture, inaccessible when the hood, trunk are closed. Triggers need to be lubricated periodically to prevent sticking and corrosion. 5. The shock sensor is installed in the cabin, the center of the car can be considered ideal, it is attached to the metal of the body with self-tapping screws or glued. 6. Additional sensors are installed in places that provide the best quality of work. 7. Contacts in places of breaks in the ignition circuits, starter, etc. soldering is recommended. More information about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 25 TOMAHAWK TW-7010 III. System connection. Main connector 14 PIN. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Red wire - system power (connect to the "+" battery terminals through a 15A fuse). Green-black wire - output "+" of the marker relay contacts (connection through a 7.5A fuse). Black wire - power "-" of the system (ensure a strong, confident contact). Green-yellow wire - output "+" of the parking lights relay contacts (connect through a 7.5A fuse). Blue wire - output "-" polite backlight control or power window control (300mA max). Yellow wire - input "+" from the ignition switch. Black and yellow wire - output "-" control on the blocking relay (the output is programmable, 300mA max). Gray wire - output "+" control of a siren or standard horn (max 1.5A, programmable). The orange-purple wire is the handbrake wire. Connection to the "-" handbrake switch with a manual transmission or to the brake lights with an automatic transmission. Yellow-black wire - output "-" of the additional channel, appears when activated from the key fob (300mA max, programmable). Blue-red wire - input "+" door triggers. Blue-black wire - input "-" door triggers. Orange-white wire - input "-" trunk trigger. Orange-gray wire - input "-" hood trigger. Connector 6 PIN. (built-in central locking relays) 1. 2. 3. 4. 5. 6. 26 The blue wire is the central contact of the central locking release relay. The green wire is the central contact of the central locking relay. Black-red wire - normally open contact of the central locking release relay. Black-red wire - normally open contact of the central locking relay. The blue-black wire is the normally closed contact of the central locking release relay. Green-black wire - normally closed contact of the central locking relay. More information about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru TOMAHAWK TW-7010 Shock sensor connector 4 PIN. 1. 2. 3. 4. Sensor supply "+12V". Sensor power "-". Entrance "-" warning zone. Input "-" of the main zone. Additional sensor connector 4 PIN. 1. 2. 3. 4. Sensor supply "+12V". Sensor power "-". Entrance "-" warning zone. Input "-" of the main zone. OVERRIDE button connector 2 PIN. Connector 2 PIN - connector for connecting the OVERRIDE button. LED connector 2 PIN. Connector 2 PIN - connector for LED connection. Transceiver antenna connector 4 PIN. Connector 4 PIN - connector for connecting an antenna. Connector for GSM/GPS module 3 PIN. Connector 3 PIN - to connect the GSM/GPS module. More information about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 27 TOMAHAWK TW-7010 IV. Wiring diagrams Connector 3 PIN not used Additional sensor connector 4 PIN ® TOMAHAWK GSM/GPS module connector 3 PIN Transceiver antenna connector 4 PIN LED connector 2 PIN “OVERRIDE” button connector 2 PIN Shock sensor connector 4 PIN Main connector 14 PIN 4 28 Connector for central locking 6 PIN More about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru TOMAHAWK TW-7010 Blue 10A Green 10A UNLOCK COM LOCK COM Black-red UNLOCK NO LOCK NO Blue-black UNLOCK NC Green- black LOCK NC 15A Red 7.5A Green-black Black +12V from battery For side lights; “+” 7.5A Green-yellow Blue Yellow Black-yellow output “-” To parking lights; “+” Cabin lighting or raising windows; “-” 300mA Ignition switch input “+” Engine lock 300mA max Gray output “+” 1.5A max Orange-purple Yellow-black Handbrake sensor; "-" Add. channel; output “-” 300mA Blue-red input “+” of the door sensors Blue-black input “-” of the door sensors Doors +12V Doors Orange-white input “-” of the trunk sensor Trunk Orange-gray input “-” of the hood sensor Hood Shock sensor Button “Override” LED Transceiver antenna Connector for connecting GSM/GPS module Connector not used Connector for connecting an additional sensor Scheme 1 More about car alarm TOMAHAWK TW-7010 on the website http://intorg.ru 29 TOMAHAWK TW-7010 Connecting an additional electric drive 0.8 sec 87A NC Blue-black 30 COM Blue NO Black-red NC Green-black 30 COM Green NO Black-red 87 87A 87 R 15A +12V Control time 0.8 sec 87A NC Blue-black 30 COM Blue NO Black-red NC Green-black 30 COM Green NO Black-red Central lock Opening 87 87A Closing 87 R 1 - 3A +12V Scheme 3 ://intorg.ru TOMAHAWK TW-7010 Negative Control C.Z. Control time 0.8 sec 87A NC Blue-black 30 COM Blue NO Black-red NC Green-black 30 COM Green NO Black-red Central lock Opening 87 87A Closing 87 Pr 1 - 3A -12V Scheme 4 More details about car alarm TOMAHAWK TW-7010 on the website http: //intorg.ru 31 TOMAHAWK TW-7010 Connecting courtesy lighting. If your car does not have a courtesy backlight function, then Tamahawk TW-7010 can connect this service function. Blue wire 86 87 + 12V 85 87a Regular courtesy lighting unit 30 Scheme No. 5 Organization of courtesy lighting. Option 1 Blue wire 86 87 +12V 85 30 86 87 +12V +12V +12V Option 2 Blue wire 87a 85 87a 30 Scheme No. 6 32 More about car alarm TOMAHAWK TW-7010 on the website http://intorg.ru TOMAHAWK TW-7010 Engine lock connection. The Tomahawk TW-7010 security complex has a programmable blocking relay control output, which allows you to get a normally open blocking option from a normally closed starter blocking, in connection with this, the connection diagram also changes. Engine blocking. Option 1 Normally closed interlock. Black wire with yellow stripe 86 87 Yellow wire 85 87a 30 Interlock relay Fuel pump, switch, ignition coil, starter, etc. Option 2 Normally open interlock. Black wire with yellow stripe 86 87 Yellow wire 85 87a 30 Interlock relay Fuel pump, switch, ignition coil, starter, etc. Scheme No. 7 More about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 33 TOMAHAWK TW-7010 Connection of a standard horn. Tomahawk TW-7010 allows connection of both a conventional siren and a regular horn, the option of using an audible warning device is selected programmatically (see the programming table). If you decide to use a regular horn, then the connection system is shown below. Connecting a regular horn. To the standard horn activation button Gray wire 86 87 85 87а 30 Standard horn +12V Scheme No. 8 Attention! 34 Be sure to use a socket with a protection diode. More information about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru TOMAHAWK TW-7010 V. Technical data. Rated voltage +12V Current consumption when off. ignition 16mA Operating frequency 434 MHz Modulation type FM (frequency) Range*: from key fob-pager to alarm from alarm to key fob-pager up to 1200 m up to 1200 m *- The range is indicated in the absence of interference. It is influenced by many factors, such as buildings, trees, power lines, the relative position of the car and the key fob pager, weather conditions, and much more. Permissible current: Power circuit red wire (limited by a fuse) 15A Circuit of contacts of the central lock control relay (limited by a fuse) 15A Contacts of the remote lock relay 30A Siren power output "+" (gray wire) 1.5A Additional channel output "-" (programmable, yellow -black wire) 300mA Parking lights power output "+" (green-black wire, green-yellow wire) 7.5A Courtesy lighting or power window control output "-" (programmable, blue wire) Lock relay control output "-" (Programmable, black-yellow wire) 300mA 300mA More about car alarm TOMAHAWK TW-7010 on the site http://intorg.ru 35 TOMAHAWK TW-7010 Time delays: Additional channel output "-" (yellow-black wire) Programmable: 0.8 sec. 10 sec 30 sec On/Off Duration of central lock control Programmable: 0.8 sec 3.6 sec 30 sec Siren/horn output (gray wire) Programmable VI. . Keychain standard type. Impact sensor. Light-emitting diode. Antenna. Harnesses for connecting the central unit, central lock, antenna. Push button limit switch. Instruction. Packing box. ME-83 The device complies with the climatic requirements according to GOST 15150 version UHL2 (placement inside a closed cabin). The device complies with the electromagnetic compatibility requirements of GOST R 50789-95. 36 More information about the car alarm TOMAHAWK TW-7010 on the site http://intorg.ru

Ratings - 5 , average score: 4.2 ()

User manual Tomahawk, model TW-7010

Instruction Fragment

The side lights will flash 1 time, the LED will blink. For the operation steps and the procedure for disabling the Anti-Hijack mode, see paragraph 16 "Remote Anti-Hijack" LCD display indication: (f HIJACK 12 More information about car alarm TOMAHAWK TW-7010 on the website of TOMAHAWK TW-7010 16. Remote Anti-Hijack. Function used to return the car in case of forcible seizure.To activate this function, you must press and hold both buttons and the key fob at the same time with the ignition on.The parking lights will flash 1 time, the system LED will start flashing.Remote Anti-Hijack has 3 stages of operation: Stage 1: First 30 seconds after activation of the Anti-Hijack mode, the system does not manifest itself in any way, the security system allows the attacker to move away from you. -x sec Stage II: The next 30 seconds the siren emits warning "CHIRPS", side lights flash Stage III: The final stage comes after about 60 seconds. after activating the Anti-Hijack mode. The siren will turn on, the engine will be blocked. Attention! To disable the Anti-Hijack mode at stages II and III: 1. Turn on the ignition. 2. Press and hold the button. OVERRIDE for 3 sec. (the siren will sound “CHIRPA”) 3. Turn off the ignition. 4. Anti-hijack mode will be disabled. The system will remain armed. If a PIN code is programmed, the Anti-hijack mode can only be deactivated by entering the PIN code. LCD display indication: (FSHASK 17. Valet mode. Valet mode is used by the car owner if the car is transferred to third parties, for example, for maintenance. After activating this mode, the system can only perform service functions such as controlling an additional channel or central lock Activating and deactivating the Valet mode is carried out when the security is off by holding the button until the key fob-pager beeps (or the color of the LED on the additional key fob changes to green) and then pressing the button, or by holding the "OVERRIDE" button for 3 sec., with the ignition on. The activation of the Valet mode will be confirmed More about the car alarm TOMAHAWK TW-7010 on the website LCD display: z1zz 18.3 False alarm protection The Tomahawk TW-7010 security complex belongs to highly intelligent car security devices, so the system uses a complex, multi-level anti-false alarm protection algorithm. First level. At the moment of arming, the main unit tests all security zones, if any sensor is found to be defective, the system automatically turns it off and informs you about it using 4 "CHIRPs" of the siren. LCD display indication: icon of the corresponding trigger. Second level. During the armed mode, the system analyzes the operation of the sensors, if the shock sensor or an additional sensor has worked 8 times in a row, it will be disabled. 19. Remote interrogation of the state To perform a remote interrogation of the state of the vehicle, press the button 1|К. The parking lights will flash 3 times, the keyfob pager will display the vehicle status. Attention If after pressing the button. 1|E (or any other button) within 3 seconds there is no confirmation of the execution of the command and the key fob pager emits 1 “BEEP”, which means the vehicle is outside the range of the key fob pager transmitter. 20. Remote unlocking of the trunk (additional channel). Many vehicles require the installation of additional equipment to implement this function. If this option is enabled, then to unlock the trunk it is necessary to press and hold the button ||E of the key fob until the key fob beeps (or the color of the LED on the additional key fob changes to green) and then pressing the button. . The execution of the command will be accompanied by 3 flashes of parking lights and "CHIRPS" of the siren. Attention If the system was armed at the moment of unlocking the trunk, then the shock sensor and the trunk trigger will be disabled until _closing the trunk._ More about the TOMAHAWK TW-7010 car alarm on the TOMAHAWK TW-7010 website. LCD display indication: 21. Remote siren shutdown. In many countries, the use of car alarm sirens at night is prohibited (for example, in Moscow after 23 ° C), therefore, the security complex provides for turning off the siren from the key fob. To do this, it is necessary that the system is armed, then press the button. (p. LCD display indication: In this case, the system will be fully operational, with the exception of the sound notification by the siren. All information will be displayed on the keyfob LCD display. The siren is turned on by pressing the button ((C|. LCD display indication: (("^ 22 .Additional channel management.Additional...

Anti-theft complex Tomahawk 7010 belongs to the class of high-tech systems that have no analogues in the domestic market. The instructions for the Tomahawk 7010 allow you to independently connect the signaling system, set up basic functions, or troubleshoot problems that have arisen.

[ Hide ]

Specifications

Description of the main parameters of the car alarm Tomahawk 7010:

1. To provide power to the car security system, an electrical network with a nominal value of 12 volts is used. The use of alarms on heavy trucks and other vehicles where the voltage value is 18–24 volts is not allowed.
2. With the ignition off and the protection mode activated, the amount of current that the system consumes will be no more than 16 mA.
3. The value of the permissible current for the power supply circuits and contact elements of the relay is not more than 15 amperes.
4. To provide power to the contact elements of the remote blocking relay, no more than 30 amperes of current will be required.
5. The siren is powered by a gray cable, the output current value will not exceed 1.5 amperes.
6. Additional channels are powered by a black-and-yellow cable; no more than 300 mA of current is required to provide it. The same amount of current is needed to connect the courtesy backlight system and the engine blocking relay.
7. Approximately 7.5 amps for each optical device will be required to power the signaling lights.

Equipment

The basic signaling kit includes:

1. Main electronic control module. The device is designed to receive, process and transmit impulse data with a communicator. It is delivered to the market in a black plastic case, on which the name and brand of the model are applied.
2. main communicator. The device is equipped with a screen that displays information regarding the status of the alarm.
3. Spare pager. It does not have a display and feedback function.
4. Impact regulator. It is necessary to determine the physical impact on the car body. When installing, it is important to correctly adjust the sensitivity in order to prevent the occurrence of false positives.
5. Diode signaling status indicator.
6. Transceiver module.
7. Mounting set of wires for connecting an electronic module, transceiver, central lock and other devices.
8. User manual for installation and use of Tomahawk 7010. The service manual describes all the functions and nuances regarding the operation of the security complex.
9. One limit switch. The device belongs to the push-button category.
10. Package.

Limit switches for doors, as well as a siren, will have to be purchased separately, since these devices are not included in the package.

Complete set of alarm Tomahawk TW-7010

Key Features

Opportunities possessed by the security complex Tomahawk 7010:

1. The presence of an anti-grabber and an anti-scanner ensures reliable transmission of signals between the electronic module and the communicator without the possibility of interception. According to the manufacturer, no modern scanner or code grabber will be able to intercept impulses.
2. The signaling electronic unit is equipped with a non-volatile state memory module. Due to this, when the battery is disconnected and then turned on, the alarm will return to its original state.
3. The presence of an integrated two-level touch controller. Its use allows you to determine the physical impact and send information about it to the car owner's console.
4. Panic option. With its help, the car owner can activate the siren and optical devices for a certain time. This will scare away strangers who are near the machine.
5. Option to automatically reset to protection mode.
6. Ability to bypass non-working areas. If one of the security zones refuses to work for certain reasons, the alarm system will automatically bypass it. Information about the problem area will be sent to the communicator.
7. The presence of protection against false inclusions. With the correct setting of the traffic controller, the alarm will not work without a reason.
8. Option to search for a car in the parking lot. When it is turned on, the optical devices of the car will blink, which allows the car owner to determine the location of the car in a large parking lot.
9. The presence of a battery discharge indication system in the pager. The communicator screen displays the battery charge value. Thanks to this, the consumer will be able to timely replace the power source in order to prevent problems in the operation of the Tomahawk 7010.
10. The presence of an additional control channel. This channel is programmable.
11. The ability to enable protection mode when the power unit is running.
12. The electronic signaling module is equipped with several connectors. An additional controller can be connected to one of them.
13. The time interval for central locking control can be programmed. The setting time is 0.8, 10 or 30 seconds.
14. Two-stage opening of door locks and deactivation of protection mode.
15. Temporary deactivation of the sensitivity controller, as well as additional controls.
16. The possibility of delaying the inclusion of lighting in the cabin. The function is programmable and can be set to different time intervals.
17. Function of remote unlocking of a door of a luggage compartment. The option is configurable.
18. Possibility of blocking the power unit. The function is set using a normally closed or open relay.
19. The presence of a built-in relay for connecting optical devices. For this, two additional channels are used.
20. Built-in central locking. Provides additional vehicle protection.
21. The ability to control the central lock when the power unit is running.
22. Built-in engine blocker. Allows you to block the operation of the power unit in case of unauthorized access to the car.
23. The main communicator screen graphically displays the operation of all activated triggers. Also, using the display, the user can find out about the state of protection of the machine.
24. Availability of anti-hijack mode or anti-robbery function. This option is designed to protect the car owner from robbery and is intellectual. When the machine is forcibly seized and the option is correctly configured, the engine will block. The blocking process will begin after a certain time, when the attacker moves to a safe distance from the owner of the car.
25. Use of an individual password. The code is used to activate or deactivate the anti-theft function, as well as control the main options.
26. The presence of a memory module for car alarms. The display of the communicator shows complete information regarding the activation of alarms. Also, using the screen, the user can find out about the zones that have worked and led to the activation of the alarm mode.
27. Option to warn the car owner about an unlocked door when starting to move.
28. Increased range of the communicator. Ideally, this parameter is 1200 meters. But in fact it will be less. Its work is affected by weather conditions, architectural features of the area, as well as interference. If they are present, the range of the communicator will be reduced several times.
29. The car owner has the ability to connect a regular horn. This feature is programmable.
30. If necessary, the consumer can install and connect an additional remote engine start module. Depending on the module, the start procedure can be implemented by command, air temperature or timer.
31. The presence of a comfort system. If your vehicle has power windows and a sunroof, you can set these devices to close automatically when security mode is activated.

Channel 130 presented a brief overview of the Tomahawk 7010 anti-theft system.

Advantages and disadvantages

Benefits of Tomahawk 7010:

1. Effective protection through the use of conversational signal coding. According to reviews, consumers do not face the problem of electronic hacking.
2. The presence of feedback provides the possibility of constant monitoring of the signaling status in real time.
3. Wide functionality at a relatively low cost. Alarms Tomahawk 7010 are characterized by the presence of many useful features that simplify the use and configuration of systems.
4. Clear and easy-to-understand operating and installation manual. With the help of service documentation, the consumer has the opportunity to independently install and connect all signaling components. Of course, this will require some experience and skills. But in their absence, it is quite possible to complete the task on your own.

The main disadvantages of the Tomahawk 7010 include the rapid discharge of the battery in the remote control. When setting up the signaling, as well as intensive use, the battery may be discharged. If this happens on the road, where it is impossible to buy a battery, then the system will have to be controlled using the service mode.

How to install?

The procedure for installing the signaling begins with studying the circuit, when connecting, you should take into account the nuances:

1. Laying electrical circuits must be carried out away from electronic devices. Their presence can lead to interference when sending commands.
2. It is impossible to lay cables in places where there are moving elements of the body. If they are damaged, it will be difficult to find the problem.
3. Installation of all main devices of the system should be carried out away from power circuits and nodes. We are talking about ignition coils, high-voltage cables to which candles are connected, etc.
4. Before installing the security complex, you can connect all the elements according to the scheme and connect them to the battery. This will allow you to make sure in advance that the alarm is working.
5. If the car is equipped with airbags and a radio with a code, then it is not recommended to disconnect the battery. When you connect it further, the audio system will ask for a code, so we recommend that you refer to the service manual in advance.
6. Connection of all electronic modules and devices is carried out only after their installation.

General Mounting Map Tomahawk 7010

The installation procedure is as follows:

1. The electronic module of the system is installed away from sources of interference, moisture and heat. We are talking about electronic devices, as well as the heating system. If this requirement is not taken into account, the operation of the unit may be disrupted. The module is installed with the connector down to prevent drops of condensate from dripping along the wires inside the device onto the board. For installation, choose the most secretive place, for example, behind the instrument panel or in the free space behind the center console. The module is fixed using self-tapping screws, double-sided adhesive tape or plastic ties. The block must be fixed as securely as possible in order to prevent its damage as a result of vibrations during movement.
2. The siren is installed in the engine compartment. It is not included in the package, so you can not install it, but the alarm system without a siren is practically useless. The device is mounted with the horn down, this will avoid the accumulation of moisture inside the device. If the siren is autonomous, that is, it is equipped with a built-in battery, then during installation it is necessary to provide free access to the keyhole. The siren must be installed away from the cylinder block and sources of moisture to avoid the negative effects of high temperatures. Installation must be done in such a way that from under the bottom of the car the intruders do not have access to the device and its connection wires.
3. The transceiver module is mounted on the inside of the windshield, away from electronic devices and metal parts. The distance between them and the antenna must be at least 5 cm, this will avoid the possible occurrence of interference. Installation is carried out on a cleaned and degreased surface. It is not recommended to install the module under the tint film or at the bottom of the glass, this will lead to poor signal transmission.
4. The limit switch is installed on the hood of the machine. When the hood is closed, there must be no access to the switch; this must be taken into account during installation. If you purchased additional limit switches, they are installed on the luggage compartment, as well as on the doors. For installation, you will need to make holes in the metal.
5. The Valet service button is installed in a place inaccessible to the criminal, since it can be used to turn off the signaling. To hide the button, it can be disguised as one of the bundles with standard wiring by wrapping it with electrical tape. The button must be positioned so that the owner of the car has free access to it from the driver's seat.
6. The shock sensor is securely fixed in the central part of the body to the metal. There should be no plastic or rubber gaskets between it and the surface, this will lead to a deterioration in the sensitivity parameter. Fixing the device is carried out with bolts, screws or double-sided tape.
7. A diode alarm status lamp is placed on the dashboard. It must be installed so that the flickering of the diode can be seen from the street. This will mark the vehicle as protected.
8. When all components are installed and fixed, they are connected to the battery and electronic module. Laying of power lines is carried out under the plastic upholstery of the passenger compartment, in particular, under the thresholds. When laying the wire, we recommend additionally wrapping it with electrical tape. This will provide reliable protection from external influences. In addition, in the event of a burglary, it will be problematic to detect the wiring of the anti-theft complex.

User manual

Instructions for Tomahawk 7010 include a description of the use of all functions and modes.

Designations of buttons and symbols on the key fob

The designation of the buttons on the key fob and their functional combinations are shown in the photo:

Table of programming basic options Tomahawk 7010

Changing your personal password

The procedure for changing the PIN code is as follows:

1. The ignition system is turned off, for this the key is set to Off mode.
2. Emergency key Override Clicked four times.
3. The ignition is switched on, the siren will emit four sound pulses to confirm.
4. Then the service button is pressed again, this will activate the password setting function. Using the key fob, the car owner enters a new PIN code, numbers from 1 to 4 are allowed. If the number is 1, then the button with the locked lock is pressed, if 2, then open, if 3, then the key in the form of an open trunk. To enter the number 4 of the password combination, the button with the crossed out speaker is clicked. The siren sounds will inform about the successful assignment of the first digit of the password.
5. To enter the menu for setting the second digit of the password, the Override key is clicked once. To enter the next digit, the same conditions are taken into account as for the assignment of the first. The siren will chirp to confirm. After entering the password, we recommend that you write it down on a separate piece of paper so as not to forget.

Emergency stop and turn on

If the communicator breaks down or is lost, the procedure for emergency deactivation of the protection mode is performed as follows:

1. The door lock of the car is opened by the key, this will trigger the alarms. The key is inserted into the ignition and switched to ACC mode.
2. Service element Override is clicked three times.
3. The ignition is switched off. The siren speaker will emit one beep. The optical instruments of the car blink.
4. After twenty seconds, the protection mode will be activated. The door locks will not be locked at the same time, they must be closed independently from the car interior or with the help of a key.

To enable protection mode, follow the same steps. The only difference is that the guard will be activated without the 20 second interval.

The new generation car alarm tomahawk tw 7010 is a high-tech device that meets all modern safety requirements. With its low cost, the alarm system has practically no analogues and is very easy to operate.

The presence of many convenient services is complemented by a two-way communication system that provides reliable contact between the key fob and the car at a distance of up to 1.2 km.

Alarm Description

ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!

The tomahawk tw 7010 protective system is installed in any vehicle, the onboard voltage of which is 12v.

The turbo timer mode allows the turbine to cool down gradually after the engine is turned off, which allows sparing the power plants equipped with a turbocharger.

All types of transmissions are supported by selecting the appropriate mode. Any details related to the operation of the security system are contained in the instructions that come with the alarm.

Remote control key fobs

Tomahawk tw 7010 protection is completed with two key fobs at once. The main key fob equipped with a TFT screen displays information about the security system, and an auxiliary waterproof key fob is also provided.

The key fob is a remote control that runs on a regular AAA-1.5V battery, the battery life directly depends on the conditions of use. You can monitor the battery level using the corresponding indicator. Change the battery in a timely manner!

The key fob itself is equipped with five control keys and an LCD display. After pressing each button, the microprocessor generates a command that is transmitted via radio to the head unit of the protective system, where it is processed and executed.

Protection (anti-grabber) is provided, which changes the transmitted code each time, preventing the possibility of writing the command by intruders.

When the command is executed, the central unit sends a corresponding signal to the key fob, which notifies the user about this through various icons.

How to use the security complex

The Tomahawk tw 7010 security system is turned on by pressing the corresponding key once. At the same time, the parking lights of the vehicle will flash and a single warning signal will be heard (unless the silent mode is activated).

All doors, trunk and hood will be closed and the central LED will flash.

Attention! If the immobilizer function is active, arm the vehicle very carefully. If instead of a single beep you hear a double beep, then the immobilizer has been disabled.

Re-enable it. Follow the indicators on the key fob display. More detailed instructions for using the security system are contained in the operating instructions.

Attention! In the event that at the moment the tomahawk tw 7010 security system is turned on, one of the triggers is in an active state (for example, one of the doors is open), the system will signal you about this with four short beeps and flash the parking lights four times.