Replacing the hub bearing on the Hyundai ix35 is possible if the bearing comes separately from the hub. It is almost impossible to replace the hub bearing on the Hyundai ix35 on your own. At a minimum, you need pullers, a press, and you may also need a gas post if the bearing is stuck "tightly" in the hub.
Wheel bearing replacement cost:
Car services for replacing the hub bearing Hyundai ix35 in St. Petersburg:
Kupchino - 245-34-84
Citizen - 603-55-05
Bolsheviks - 701-02-01
Courage - 748-30-20
WhatApp / Viber: 8-911-766-42-33
If the replacement of the Hyundai ix35 hub bearing is not the first time on the same hub, you need to be prepared for the fact that you will have to change the hub as well. This is due to the fact that with frequent repressing, seat the hub becomes unusable. Before replacing the hub Hyundai bearing ix35 make sure to diagnose to determine which bearing needs to be replaced.
In terms of time, the replacement takes about 40-50 minutes. If additional locksmith work (gas, etc.) is needed, then the replacement time can be increased.
When to replace a bearing:
- crunching when driving in a straight line;
- growing rumble after 60 km / h;
- unusual whistle while driving;
The degree of wear can only be determined during diagnostics.
Work guarantee- 180 days.
Which wheel bearing to choose:
1. FAG (Germany)
2. SKF (Sweden)
3. Ruville (Germany)
4. Febi (Germany)
5. Patron (European Union)
When buying a bearing from a blunt with us, we will provide a discount for the replacement.
Available in front suspension separate replacement hub bearing. And on rear suspension this bearing is changed only in assembly with the hub itself. Accordingly, in the first case, the spare part itself is cheaper, but the work of replacing it is quite laborious. And in the second case, the hub assembly for the Hyundai iX 35 is more expensive, but it is easier to replace it.
Work order
Technology for replacing the front hub in a Hyundai ah35 car:
- the car is lifted up
- the wheel is unscrewed
- removed stopping support
- removed brake disk
- unscrewed rounded fist complete with hub
- the hub is pressed out of the steering knuckle
Then assembly is carried out in reverse order. Replacement rear hub produced in a similar way.
Replacing the front hub bearing
To replace the front hub bearing on the Hyundai ix35, the hub itself is first dismantled using the technology described above. Then, with special narrow-ended pliers, the wheel bearing retaining ring is compressed and removed from the groove of the steering knuckle.
After that, the hub is pressed out of the inner ring of the bearing and the bearing itself is removed from the steering knuckle. Seat surfaces are treated against rust and lubricated grease. Then new bearing must be pressed into the hole of the steering knuckle of the car.
For all types of work on the replacement and repair of hubs and bearings in the network of our car services, a guarantee is provided. Hubs and bearings of original and non-original production are available. we will provide you excellent quality works and competitively low prices.
The content of the article:
Before replacing a Hyundai ix 35 wheel bearing, be sure to make a diagnosis to determine which bearing needs to be replaced.
Up. Hyundai ix 35 LeichtPanzerKampfwagen › Logbook › Replacing the front support bearings and front left wheel bearing.
This is interesting! The Hyundai logo is not just the letter "H" in aval. It would be too easy. This emblem symbolizes the handshake of two people - a representative of the concern and satisfied customer. In addition, the word “hyundai” is translated from Korean as “modern”.
Car service "Auto-Mig" > Hyundai repair > Bearing replacement Hyundai hubs IX removal of the front hub assembly. Pressing out the broken wheel bearing and pressing in the new one.
The nearest streets to the entrance are Marshal Biryuzov, Berzarin, People's Militia, Sorge, Kuusinen, Raspletin .. I drive and enjoy the silence in the suspension. Loosen the two nuts that fasten the shoe guide and the steering knuckle.
Club Hyundai ix55 - Hyundai Veracruz - Wheel bearing replacement
AngelBlack and Hyundai ix35 LeichtPanzerKampfwagen before: Toyota Auris and Mitsubishi Lancer. When replacing brake discs sentenced front oprnyye bearings. When scrolling, the crunch was concrete. How was this not noticed in the OD when diagnosing the suspension? Most likely not diagnosed at all. Support took the original R After the holidays signed up for a replacement. There is no point in describing the process.
Only the masters were again surprised at the thickness reinforced springs.. Also, after the frost, a rumble with a slight beating began to appear in front on the left. As a result, the front left wheel bearing was sentenced. I read on the forums that SKF and ILJIN mainly go to the conveyor. I took SKF BAHA, it seems like the quality is better. ILJIN stood at the opening. After replacement, everything is good. I go and enjoy the silence in the suspension.
