Repair of plastic parts. Options for the restoration of plastic elements of the car interior

Repair of plastic parts. Options for the restoration of plastic elements of the car interior

21.06.2019

Plastic repair professionally in Moscow, repair time from 15 minutes.


We repair plastics of almost any brand, plastic products of various shapes and configurations.

Breaking plastic products is a fairly common problem these days. Many plastic products crack, break and become unusable during operation. Plastic welding, or as this process is also called, plastic soldering, will help in restoring broken parts.



Soldering plastic is a process that requires careful preparation, specialist experience and a correct assessment of the maintainability of the product. If you do not follow all the features of the technology, then the seam will turn out to be brittle and will not withstand even minor loads.



How to repair a plastic part? There are several methods for welding. One of them is hot air bar welding. For each repaired product, a certain welding temperature is selected, otherwise the surfaces simply will not grab each other. Correctly selected temperature is not the main thing in repair, you need to carefully prepare the surface, cut the edges in a special way and clean the surface.



There are several ways to repair a crack in plastic. To determine the technology of welding plastic, you need to know the nature of the damage and the material of the plastic. Soldering a crack in plastic can take anywhere from 1 to several hours. The process of welding a plastic product must take place in strict accordance with temperature and other factors, it is rather problematic to repair the plastic yourself, it is possible to overheat the plastic part and make it unrepairable.




Another repair method is the extrusion method. This is the most effective technique that allows products to work hermetically and under loads in the future. Not all products can be repaired using extrusion welding, sometimes the thickness of the material or its properties allow repair only using the bar method. To start work, it is necessary to determine the material from which the part is made, then select the method of work and proceed with the restoration of the broken product. Each polymer (and there are a large number of their varieties) has its own melting point, therefore, for repair, you need to select temperature regime individually for each product.

If the question arose how to close a crack in plastic? - Contact us, we will be happy to help carry out the repair.

Recovery plastic parts carried out only by professional specialists, which guarantees full compliance with the technology. In our work, we use certified material for the restoration of plastic products and parts.

Plastic is a universal material, but it must be handled carefully and carefully, because its strength closely borders on fragility.

Our workshop offers a full range of restoration services and plastic repair any sizes and shapes.

Only involved in the work professional equipment, which allows you to repair efficiently and quickly in the shortest possible time.

We use a special technology that allows you to restore the surface with high quality. Thus, the product receives the original attractive appearance.

Features of plastic repair

should be carried out by qualified specialists who have all the nuances and skills in the relevant field.

It is important to take into account the details when repairing. For example, polypropylene or polyethylene, the most common types of plastic, have a limited range of temperatures at which they function. It varies from -15 to +120 degrees Celsius.

That is why it is impossible to use cold welding or other adhesive substances in the work.

We work with hot air welding technology, which qualitatively allows you to restore the damaged element.

It is also important to take into account other features of the part, for example, whether pressure arises during its operation. After all, at heavy loads a soldered seam may not withstand and again become unusable.

Plastic repairs can be done with polymers in several colors, including blue, white, green, gray and black. The repaired part becomes sealed.

What do we offer?

When you work with us, you get first class service. affordable price. There are two reasons for this: firstly, we have a powerful material and technical base at our disposal, which allows us to independently install pricing policy our work.

Secondly, our specialists have a significant work experience - from 5 years, which allows them to quickly eliminate even the most complex breakdowns.

We work 24 hours, so we can take on repairs within a whole day.

If you have any questions, our consultants will be happy to answer them.

We will also provide you with an online consultation on the topic you are interested in completely free of charge. To contact us, call the number listed on the website.

Repair of plastic has its own price list, the prices of which depend on the degree of damage to the product. We also provide a guarantee for the services provided.

Plastic soldering is a service, the experience of providing which in our workshop is colossal.

Give us a call and we will surely surprise you!

You will need

  • - soldering iron or glue;
  • - acetone;
  • - sponge;
  • - emery;
  • - fiberglass;
  • - solder wire;
  • - clamp or masking tape;
  • - fittings;
  • - primer for plastic;
  • - dye;
  • - varnish.

Instruction

Find out the composition plastic- its marking should be indicated on the inside of the product (for example, PA - polyamide or PP -). It is important to study the properties of this material, since the type of bonding or welding will depend on this. Thermoplastic polymers (plexiglass, polyethylene, polypropylene and others) are easy to process. But you will not be able to melt the so-called thermoplastics (they contain phenol-formaldehyde, epoxy and other resins and fillers). You will need special glue.

Pick up in building material adhesive, epoxy for this type of plastic and consult a competent seller. Follow the manufacturer's instructions exactly. Sand the surfaces to be bonded, clean them of dirt and degrease with acetone. You can glue the fault directly along the seam, or you can pre-strengthen it with fiberglass.

Use an identical solder wire to solder a leaky plastic part. chemical composition. Treat the working parts with sandpaper a centimeter from the edge, as the part to be welded will have to step on the left allowance for the strength of the seam. Gather the pieces of broken plastic and fix them with a clamp (fixing tool) or masking tape.

Start thin plastic from the “face” so that an ugly bump does not appear on the visible surface. You can repair plastic of a denser composition immediately from the wrong side. Run the soldering iron over the crack; apply solder and fuse it into the thickness of the softened material. From the back of the work, you can use a thicker wire.

Some masters combine soldering plastic with reinforcement (reinforcement of the structure). To do this, it is recommended to purchase a special brass or bronze mesh (about 0.2 mm thick). Reinforcing material cut into strips right size. Your task is to attach the amplifier to the inner surface of the chip and (heating the plastic with a soldering iron) drown it in the molten material.

Get ready for cosmetic repairs plastic. The glued or soldered surface must be washed, sanded with #1000 sandpaper and wiped with acetone.

Shake the can of primer to plastic, shake it for 10 minutes and apply to the damaged part from a distance of 20 cm. If the packaging has other instructions, be sure to follow the manufacturer's recommendations. Cover the plastic with 2-3 layers (depending on the depth of damage), let it dry and go over the product again with emery and acetone.

Repair of plastic car parts can be local or complex. When local repair plastic part, its repair is done without removing the part from the car. In a comprehensive body repair, the part is removed and, after repair, is mounted in place.

Stages of repair work:

  • removal of part cracks (if necessary)
  • straightening a deformed plastic part using high temperature (if necessary)
  • puttying and grinding of damaged parts of the part
  • priming and painting the prepared parts of the part, drying
  • varnishing

Sometimes, at severe damage plastic, the restoration of plastic parts is impossible. In this case, it is better to replace the plastic part of the car with a new one. Technical center managers body repair help with the selection of plastic parts and, at the request of the car owner, make a purchase.

The bumper is perhaps the most damaged body part car. It is extremely easy to get damage to this body part: dents, cracks, abrasions.

Our technical center has extensive experience in repairing plastic bumpers, fenders, hoods and other plastic elements and car parts.

We can restore the original shape of a bumper or other plastic part of a car by soldering, reinforcing and applying special material for plastic repair. Let's make painting of a plastic detail of the car.

Despite the fact that plastic is not the most common material used in the manufacture of a car, car plastic repair has always been an important activity in the field of car care and maintenance.

Speaking about the plastic components of the car body, we can first of all recall the bumper of the car, which, as a rule, is made of plastic. Plastic is also used to create covers for mirrors, where it is especially susceptible to various kinds of damage, as well as in many other car parts, especially inside the car.

In the event of damage to the plastic in the car, repairing plastic parts will be the best way out. Of course, the first thought that will haunt the car owner is the replacement of damaged parts, but it is fair to say that many plastic components of the car are subject to restoration even in the event of severe and severe deformation.

We will repair the plastic parts of your car

Repair of interior plastic parts is one of the most common works performed by employees of the NIVUS technical center. Since various kinds of traffic accidents entail damage not only to the body part of the car, but also to the interior of the cabin, the plastic parts in it often turn out to be broken and destroyed. In this case, the specialists of the technical center are taken to repair the plastic products of the machine.

Note that the repair of plastic parts of a car is the procedure that should be entrusted to professionals. The reason for this is the “capriciousness” of plastic as a material, which makes it difficult for an inexperienced person to work with it. And the repair itself has many nuances that only qualified specialists are usually familiar with, because there are many stages of it and all of them are far from being as simple as it might seem at first glance.

This process consists of several stages:

  • impact on the item high temperature;
  • its gluing;
  • straightening the part;
  • putty;
  • detail grinding;
  • primer details;
  • painting;
  • applying lacquer to the item.

If you need to repair the plastic of the car interior - the employees of the center Maintenance"NIVUS" will carry it out with the highest quality and in the shortest possible time. Repair of plastic in the technical center "NIVUS" is a guarantee right choice and worthy of your car repair!

© 2023 globusks.ru - Car repair and maintenance for beginners