Symptoms: knocks in the rear suspension of the car when starting it off, grinding in the rear suspension of the car when driving, rear wheel alignment angles are violated.
Possible reason: Damaged wishbones rear suspension car.
Tools: jack, wheel chocks, stops under the body, a set of wrenches, a set of sockets.
Front wishbone rear suspension:
1. Apply the parking brake and place chocks under the front wheels.
2. Raise back vehicle and secure it with jack stands.
3. Remove the rear wheel.
4. Remove the nuts holding the rear transverse wishbone to the knuckle while holding the bolts from turning.
5. Remove the nuts securing the front rear wishbone to the subframe bracket while holding the bolts from turning.
6. Remove the front transverse arm of the rear suspension.
7. Make a thorough inspection of the lever for deformations, signs of wear and damage to the threaded part of the adjusting sleeve. If these defects are present, the lever must be replaced.
8. Press out the silent block using suitable mandrels, and then inspect it for tears, one-sided swelling and delamination of rubber from the metal sleeve. If these defects are found, the silent block must be replaced (This operation does not make sense if defects were found during step No. 7).
Note: if there are no defects on the lever and on the silent block, press the silent block using the mandrels that were used in the execution of paragraph No. 8 of this instruction.
9. Install the front wishbone rear suspension in reverse order of removal. Finally tighten the nuts of the front transverse wishbone mounting bolts of the rear suspension with the car standing on the ground to a torque of 140-160 Nm.
Attention! After installing the front transverse arm of the rear suspension, check and, if necessary, adjust the angles of the rear wheels.
Rear wishbone rear suspension:
10. Brake the vehicle using the parking brake, then chock the front wheels.
11. Remove the rear wheel.
12. Raise the rear of the vehicle and place secure supports under it.
13. Remove the rear wheel.
14. Turn away the nuts fastening the back cross-section lever of a back suspension bracket with a fist; keep the bolts from turning.
15. Remove the nuts securing the rear transverse wishbone to the subframe bracket while holding the bolts from turning.
16. Remove the mounting bolts and dismantle the rear transverse arm of the rear suspension
17. Make a thorough inspection of the rear suspension arm for cracks, chips, chips and deformations. If defects are found, the lever must be replaced.
18. Press out the silent block using suitable mandrels. Inspect the silent block for breaks, one-sided swelling and delamination of rubber from the metal bushing. If these defects are detected, the silent block should be replaced (This operation does not make sense if necessary complete replacement rear wishbone rear suspension).
Note: replacement of the silent block is carried out by pressing with mandrels that were used in the operation described in paragraph No. 18.
19. Install the dismantled parts in reverse order. The fixing nuts of the rear arm of the rear suspension are tightened with the vehicle installed on the ground to a torque of 140-160 Nm.
Note: After installing the rear suspension arm, it is necessary to check and adjust the rear wheel alignment.
Symptoms: knocks and squeaks in the rear suspension, the rear wheel alignment angles are violated.
Possible reason: rear suspension trailing arms damaged.
Tools: jack, wheel chocks, a set of wrenches, a set of heads, mandrels for pressing out silent blocks (suitable heads can be used).
1. Brake the car parking braking system and install wheel chocks under the front wheels.
2. Raise or hang out the rear of the car, and then place it under reliable and strong stops.
3. Remove the rear wheel.
4. Turn off and take out the bolts fastening the trailing arm of a back suspension bracket with a fist.
5. Unscrew and remove the bolts securing the trailing arm of the rear suspension to the bracket located on the car body.
6. Remove the rear suspension trailing arm.
7. Carefully inspect the trailing arm for cracks, chips, splits, deformations, abrasions and other signs of destruction. If defects are found, the lever should be replaced.
8. Press out the silent block trailing arm rear suspension using suitable mandrels. Inspect the silent block for breaks, cracks, one-sided buckling and delamination of rubber from the metal bushing. If these defects are found, the silent block should be replaced (this operation does not make sense if defects are found on the lever, since if defects are found, the lever must be completely replaced).
Note. The silent block should be pressed in with the same mandrels that were used when it was pressed out. If there is an arrow on the silent block, then it should be directed along the axis of the lever when pressing.
9. Install the removed parts in reverse order. Finally tighten the lever mounting bolts with the car standing on the ground to a torque of 100–120 N∙ m.
10. Check and, if necessary, adjust the wheel alignment.
Pavel Kurakin Motorist
You will need: keys "for 14" (two), "for 17", "for 19", pliers, a container for collecting working fluid power steering systems, puller for ball joints.
1. Hang the car on a lift or raise the front of the car above the inspection ditch. Remove the front wheels.
2. In the passenger compartment under the instrument panel, unscrew the bolt of the terminal connection of the steering shaft with the steering column shaft ...
3. ...and separate the shafts.
4. Press out of the levers steering knuckles pins of the hinges of the outer tips of the steering rods (see. " Replacing the outer tie rod end »).
11. Turn away a nut of fastening of a finger of the lower hinge of a rack of the stabilizer, keeping a finger from turning, and disconnect a finger from a bar of the stabilizer.
12. Turn away nuts of bolts of forward...
13. ... and the rear supports of the power unit ...
14. ... and remove the bolts.
15. Install supports under the subframe.
16. Turn out on two bolts and turn away on one nut of fastening of arms right and left rear supports subframe...
17. ... and then remove the brackets.
18. Turn out two bolts of fastening of forward supports of a subframe to a body...
19. ... and remove the bolts with the lower plates of the front supports.
20. Turn off two nuts of fastening of back supports of a subframe to a body...
21. ... and remove the front suspension subframe assembly with lower control arms, steering gear and stabilizer bar by lowering it down. If necessary, remove the stabilizer bar (see " Replacing parts of the front suspension anti-roll bar”), steering gear (see “
Replacement of silent blocks Hyundai Tussan produced as wear and tear given element. This can be detected with timely diagnosis and visual inspection. Car service "Bers-Avto" offers to use comprehensive services diagnostics, repair and replacement of worn parts. We offer the services of professional mechanics who will quickly and efficiently perform all types of work at reasonable prices.
Replacement of silent blocks Hyundai Tucson in our service is carried out in accordance with the current service standards, which allows us to provide services at a professional level.
Replacing the front silent blocks Hyundai Tussan
Timely replacement of the silent blocks of the Hyundai Tuscon front levers allows you to make driving a car comfortable and safe, as well as reduce the risk of failure of other suspension elements.
Normally, during the operation of vehicles under normal conditions, diagnostics should be carried out every 50 thousand kilometers. This precaution reduces the risk of failure of the suspension and other parts. Replacing the front silent blocks of the Hyundai Tussan may be required if such malfunctions of this element are detected:
- When driving in a straight line, the vehicle skids to the side.
- Lateral wear of the protectors is observed.
- When braking, the transport enters.
- When driving, body vibrations are observed.
Another diagnostic sign that indicates the need for such an event as replacing the silent block of the front levers of the Hyundai Tussan is visible signs of wear of the spare part, a violation of the integrity of the body.
At the first signs of wear of the spare part, you should contact a professional service, whose mechanics will diagnose and take the necessary repair measures.
Hyundai Tucson rear silent blocks replacement
Timely replacement of silent blocks rear control arms Hyundai Tuscon allows you to prevent the destructive effects of vibration on other elements of the chassis. In turn, this reduces the cost of Maintenance transport. In the Bers-Avto car service, the Hyundai Tuscon rear silent block is replaced, which is performed when the spare part fails. This helps prevent damage to the unit and the need for costly repairs. The biggest threat is that a breakdown can occur while driving.
