Refueling volumes Nissan Teana J32
RECOMMENDED FLUIDS AND LUBRICANTS Fluids and Lubricants
|
Capacity (Approximate) |
||||
|
Letter |
Imp measure |
Recommended Fluids/Lubricants |
||
|
Engine oil Drain and refill |
With oil filter change |
4.6 |
4 qt |
Genuine NISSAN engine oil 1 |
|
Without oil filter change |
4.3 |
3-3/4 qt |
API grade SL or SM* 1 ILSAC grade GF-3 or GF-4* 1 |
|
|
Dry engine (engine overhaul) |
5.3 |
4-5/8 qt |
ACEA A1/B1, 3/B3, A3/B4, A5/B5, C2 or C3* 1 |
|
|
Cooling system (with reservoir) |
9.1 |
8 qt |
Genuine NISSAN Engine Coolant or equivalent |
|
|
Reservoir tank |
0.8 |
3/4 qt |
in its quality* 2 |
|
|
CVT fluid |
RE0F10A |
8.3 |
7-1/4 qt |
Genuine NISSAN CVT Fluid NS-2* 3 |
|
RE0F09B |
10.2 |
9 qt |
||
|
power steering fluid |
1.0 |
7/8 qt |
Genuine NISSAN PSF or equivalent* 4 |
|
|
brake fluid |
— |
— |
Genuine NISSAN brake fluid, or equivalent DOT 3 or DOT4 (US FMVSS No. 116)* 5 |
|
|
Multi-purpose grease |
— |
— |
NLGI No. 2 (Lithium soap base) |
|
*1: For further details, see "SAE Viscosity Number".
*2: Use Genuine NISSAN Engine Coolant or equivalent in its quality, in order to avoid possible aluminum corrosion within the engine cooling system caused by the use of non-genuine engine coolant.
Note that any repairs for the incidents within the engine cooling system while using non-genuine engine coolant may not be covered by the warranty even if such incidents occurred during the warranty period.
*3: Using transmission fluid other than Genuine NISSAN CVT fluid NS-2 will damage the CVT, which is not covered by the war-
Mi DEXRON™ VI type ATF can be used.
*5: Never mix different types of fluids (DOT3 and DOT4).
- Fuel - 70 liters.
- - 4.6 l. with oil filter and 4.3 l. without him. Oil class: API SG/SH/SJ.
- - 9.1 liters, with a reservoir (expansion tank), from the bottom 0.8l tank. Genuine Nissan antifreeze or equivalent.
- - for the RE0F10A box - 8.3 liters. For box RE0F09B - 10.2 l. Oil type - Genuine NISSAN CVT Fluid NS-2
- - total volume - 1 l. Liquid type - DEXRON III.
- - about 0.7l. The type of brake fluid recommended is Genuine Nissan brake fluid or DOT3 and equivalents.
- Multipurpose lubricant - consumption as needed. Grease type: NLGI #2 lithium based.
- - 500 + - 50 g. HFC-134a (R-134a).
- - 150 g genuine Nissan oil for type S air conditioning systems or equivalent.
- - 5 l. The type of liquid used is water. If necessary with additives of detergents.
Engine oil
How much oil to pour [Nissan Teana J32]?
Based on the recommendations of the Nissan repair and maintenance manual, it is necessary to fill4.6 litersoil with a filter change, and 4.3 liters without a filter change. At the same time, many services fill in 4.7 liters, this volume of oil corresponds to the maximum permitted oil level (marksHon the dipstick).
Recommended viscosity:
Nissan recommends choosing the viscosity of the oil based on the climatic conditions of the machine, which is clearly shown in the last figure.
Oil manufacturer recommendations:
Of course, the Nissan auto concern recommends using its own oils. However, most modern oils are of sufficiently high quality, on the basis of this, a large assortment is opened before the car owner to choose from: but the oils still differ in their characteristics, for example, some are better cleaned of carbon deposits, others burn and quickly evaporate, others are highly adsorbed or reduce wear details properties. Given all this, it is very difficult to advise any particular oil, I personally chose Nissan Oil .
Given all this, it should be noted that I still fake oils, so you should buy oil only in trusted places, wholesale depots or large auto stores. In this case, the oil must correspond to the viscosity level of API SF, SG or SH!
Engine cooling system
Recommended manufacturer: The Nissan Repair and Maintenance Manual recommends that you strictly observe the level of coolant (antifreeze) and add it if necessary. In this case, if topping up is required too often, you must immediately contact the service center for diagnostics of the cooling system. You can use coolant any manufacturer based ethylene glycol. Using other types of refrigerant solutions may damage the cooling system!!!
Transmission oil
To change the oil in the variator, contact the service center!
What is the amount of oil (fluid) gearbox [Nissan Teana J32 ] ? To correctly measure the oil level in the automatic transmission, you must use a special dipstick (its location is shown in the figure on the right). The dipstick has notches that determine the normal oil level for hot or cold measurement. Total in automatic transmission 8.3 or 10.2 liters.
Power Steering Fluid
The liquid level is determined visually by the power steering barrel (the maximum and minimum of the power steering fluid level are indicated on it) [ See the figure to the right ].
There are 2 scales for measuring power steering fluid -for cold measurement
Andfor hot measuring
.
Undercold is understood as the level when the temperature of the liquid is in the range from0°С to 30°С .
Hot the level corresponds to the liquid temperature from50°С to 80°С .
The history of the Teana model began in 2003, when a new D-class car came to replace the obsolete Maxima. In terms of technical characteristics, the Nissan concern opposed its “brainchild” to no less advanced models of the Subaru Legacy, Skoda Superb, Ford Mondeo and Volkswagen Passat. Only powerful engines could compete with such cars, and Nissan took care of that. The first generation Teana (J31) was produced from 2002 to 2009. During this period, gasoline engines with volumes of 2.0, 2.5 and 3.5 liters worked under the hood of the car. The 2.0- and 3.5-liter versions were front-wheel drive, while the 2.5-liter was all-wheel drive. In terms of power, the power plants were in a fairly wide range: this is 145 hp. for a 2 liter engine and 231-245 hp for volume 3.5. As for the transmission, on all modifications, except for 3.5 (CVT-variator), there was a 4-speed variator. Below in the article will be provided information on what kind of oil and how much to fill in these units.
The debut of the Nissan Teana J32 took place in 2008 in Beijing. The second generation borrowed the Nissan D platform and was equipped with engines with the same volume as in the previous generation. The uncomplicated design of the predecessor was corrected by new design features that made the car even sleeker. For the domestic market, modifications were offered with engine powers of 167 hp. (2.5l.) and 250 hp (3.5l.), Paired with a new electric transmission without steps CVT XTronic with adaptive gear ratio shifting.
Due to the technical diversity and rather large dynamics of engines, Nissan Teana quickly became a popular favorite. Not every model can offer all-wheel drive at a reasonable price while maintaining driving comfort and excellent driving performance.
Generation J31 (2002 - 2009)
Engine Nissan QR20DE 2.0 l. 145 HP
- Oil types (by viscosity): 0W-30, 5W-20, 5W-30, 5W-40, 10W-30, 10W-40, 10W-60, 15W-40, 20W-20
- How many liters of oil in the engine (total volume): 3.9 liters.
Engine Nissan QR25DE 2.5 l. 160 HP
- What engine oil is poured from the factory (original): Synthetic 5W30
- Oil types (by viscosity): 5W-30, 5W-40
- How many liters of oil in the engine (total volume): 5.1 liters.
- Oil consumption per 1000 km: up to 500 ml.
- When to change oil: 7500-15000
Changing the oil in a Nissan Teana engine is one of the most important procedures in car maintenance. The overall engine life depends on the correct and TIMELY replacement of engine oil. And any car owner wants his "iron horse" to travel as long as possible and at no additional cost. And this is quite achievable. It is enough to adhere to the following rules:
- 1. Properly operate the car.
- 2. Carry out maintenance in a timely manner.
- 3. Use only original fluids and spare parts.
What tool is needed to change the oil in a Nissan Teana engine?
Changing engine oil is not a very complicated procedure, so it does not require special tools. A pair of keys from the standard set of motorists will suffice.
You will also need a suitable space. An ideal option would be a box equipped with a lift or a garage with a pit. Work can also be done on a trestle if weather conditions permit. But if none of the above is present, then you can get by with an ordinary garage. And to raise the car, a regular jack will do.
Also, do not forget that a container is needed to drain mining. You can cut off an old canister of oil, or you can get a plastic basin.
In order to make it more convenient to pour oil into the engine, we need a funnel. You can buy it at any hardware store or make it from a soda bottle.
What else is needed to change the oil in a Nissan Teana engine?
As consumables for changing the oil in a Nissan Teana engine are engine oil, an oil filter and a drain plug gasket. Our work requires far fewer spare parts than for.
Engine oil - KE90090042R. This is genuine Nissan oil and is recommended for use in the Teana engine.
Oil filter - 152089F60A - original, but you can take any double of normal quality, for example VIC, PIAA, FILTRON.
Drain plug washer - 11026-01M02. This is a regular copper gasket that is changed after each unscrewing the drain plug.
Oil change interval in the Nissan Teana engine
Engine oil, like the oil filter, on a Nissan Teana car changes after 15 thousand kilometers or after a year, whichever comes first. But I recommend boldly reducing this interval by 2, since the additives found in ANY engine oil hardly "survive" up to 9 thousand kilometers. Therefore, decide for yourself - do you want to skate an extra couple of kilometers in order to save on one oil change and then add this oil to the engine in liters?
By the way, along with engine oil at the same time I. It takes a little money, but it immediately becomes easier to breathe in the cabin.
The progress of work on replacing engine oil in the Nissan Teana 2.5 engine
In our case, the work is carried out on a NISSAN TEANA car with a VQ25DE engine. But on other motors, this procedure is performed in a similar way. Consumables will be the same as the amount of oil. QR20DE, VQ23DE and VQ35DE engines will require about 4 liters of new oil. The original is sold in 5 liter canisters, so such a canister is enough in any case.
1. Before you start changing the oil in the Nissan Teana 2.5 engine, you need to dismantle the protection and warm up the engine to operating temperature. We remove the protection in order to crawl to the drain plug. If the protection has a special technological hole for this, then it is not necessary to dismantle it. We warm up the motor until the fan works. When the fan turns off, we go down under the car and proceed directly to replacing the engine oil in the Nissan Teana 2.5 engine.
2. With a 14 "wrench, unscrew the drain plug and, substituting a container for working out, drain it. At this moment, be extremely careful, as the oil is hot and can burn you if it gets on your skin.
3. When the oil has stopped dripping, we wrap the drain plug in place and do not forget to install a new sealing ring on it.
4. Now you need to unscrew the oil filter. This is done from under the right fender liner. There is enough space, so we just unscrew the filter by hand. Be prepared for some more oil to leak out of the filter, so either put some kind of container under it or put a rag on it.
5. The new filter is installed in place in the reverse order, but it is required to lubricate the filter rubber with engine oil before installation. The filter is tightened by hand.
6. We proceed to refueling the engine with new engine oil. Insert a funnel into the oil filler neck and fill in fresh oil.
The oil level is controlled with a dipstick. Fill with new oil until its level reaches the maximum mark. After that, close the filler cap and start the engine. We are waiting for the oil pressure lamp to go out. Then we turn off the engine and wait a couple of minutes. Take out the dipstick and check the level. If the level is between the MIN and MAX marks, then you can turn off the work - the oil change in the Nissan Teana 2.5 engine is over. Otherwise, add the required amount of liquid.
Oil change in the Nissan Teana J32 engine video
The video of changing the oil in the Nissan Teana J32 engine clearly shows the whole process of work:
This option is suitable for those who do not like to read a lot of text, but want to see everything with their own eyes.
Disposal of exhaust and filter after oil change in Nissan Teana engine
After you have drained the oil into a basin, pour it into any container, but do not pour the used oil on the ground! This greatly pollutes the environment. If you do not use mining for personal purposes, then for sure in any garage cooperative there are people who heat their garages with special furnaces for mining. If there are none in mind, then working off can simply be put next to the garage door. Often, people go to garage cooperatives and collect mining for its further use or processing.
The oil filter can simply be thrown into the trash. Only before that it will be necessary to drain the remaining engine oil from it.
That's all! Do not remain indifferent and do not harm nature! Thank you for your attention and see you on our website!
Many motorists, when choosing a lubricant, do not take into account the recommendations of the car manufacturer, but buy any well-known brand of synthetics. This approach to the selection of motor oil can result in a major overhaul of the motor. This article lists the recommended engine oil for Nissan Teana.
The manual for the car indicates the recommended engine oil, Nissan Teana is no exception. The manufacturer of the machine in the manual describes the characteristics of the lubricant:
- Class;
- viscosity;
- features of the use of different oils depending on the temperature outside the car.
After studying the instructions, you can choose a motor fluid that provides optimal operating parameters for the power unit. In this case, it is worth considering:
- The season for which the lubricant is designed. Do not use fluids designed for summer in winter, or pour all-weather lubricants in too hot climates. The use of grease designed for the winter in the summer will lead to overheating of the motor. All types of oils differ in fluidity, the number of additives, and quality characteristics.
- Base engine fluid. The use of a mineral base is unacceptable for most modern motors. Their optimal performance is provided by synthetics or semi-synthetics.
- The presence of a special marking with tolerances on the canister indicates that the fluid is suitable for a particular type of engine.
The purchase of oil for a power unit should be deliberate, the purchase of a fluid that does not meet the recommended parameters can harm the motor and lubrication system.
Nissan Teana J31 2003-2008 release Oil quality class
According to the manual for car engines running on gasoline, it is worth using motor fluids that meet the following requirements:
- QR20DE engine:
- original Nissan engine fluid;
- according to API classification - SG, SH, SJ or SL;
- according to the ILSAC standard - GF-1, GF-2 or GF-3;
Refueling tank for QR motors, i.e. the volume of oil required for replacement, with an oil filter 3.9 liters and without 3.7 liters, a dry engine will require 4.5 liters of oil.
- Power units VQ23DE or VQ35DE:
- Nissan branded oil;
- according to the API standard - SL, SJ or SM;
- according to ILSAC requirements - GF-2, GF-3 or GF-4;
- according to ASEA specification - A2.
Filling capacity for VQ engines, i.e. the volume of oil required for replacement, with an oil filter 4 liters, without changing the filter - 3.7 liters, a dry engine will require 5 liters of oil.
Oil viscosity
It is preferable to use SAE 5w - 30 fluids. In the absence of the specified car oil, you need to choose the appropriate one according to scheme 1.
Scheme 1. Classification of oils according to viscosity characteristics for gasoline engines, depending on the ambient temperature range. According to the scheme, it is necessary to apply:
- 5w - 20, if the temperature is -30°С (or less) to +40°С (and higher);
- 5w - 30, at a temperature of -30 ° C (or less) to +40 ° C (or more);
- 10w - 30; 10w - 40; 10w - 50 in the temperature range -20°C to +40°C (or more);
- 15w - 40; 15w - 50 in the temperature range -15°C to +40°C (or more);
- 20w - 40; 20w - 50 in conditions of -10°C to +40°C (or more).
5w - 20 is only used for QR motors. The specified oil is not suitable for continuous use at high speed.
Nissan Teana J32 2008-2014 release
Oil quality class
The operating instructions for the machine indicate the following requirements for engine oils applicable in gasoline engines:
- Motors VQ25DE or VQ35DE:
- genuine Nissan lubricant or equivalent;
- according to API - SL or SM;
- according to the ILSAC standard - GF-3 or GF-4;
- ACEA quality class - A1/B1, A3/B3, A3/B4, A5/B5, C2 or C3;
Filling capacity for VQ engines, the amount of oil required for replacement, with an oil filter 4.6 liters, without - 4.3 liters, a dry engine will require 5.3 liters of oil.
Oil viscosity
Scheme 2. Classification of motor oils for gasoline engines by viscosity depending on the ambient temperature range. According to scheme 2, it is worth using:
- 5w - 30; 5w - 40 at -30°C (or less) to +40°C (and above);
- 10w - 30; 10w - 40; 10w - 50 at -20°C to +40°C (or more);
- 15w - 40; 15w - 50 at -15°C to +40°C (or more);
- 20w - 40; 20w - 50 at a temperature range of -10°C to +40°C (or more).
Nissan Teana L33 from 2014
Oil quality class
- original NISSAN engine fluid;
- according to API standard - SL, SM or SN;
- quality class according to ILSAC - GF-3, GF-4 or GF-5;
The filling capacity (volume) of oil for QR and VQ engines when replacing with an oil filter is 4.6 liters, without a filter - 4.3 liters.
Viscosity
In the absence of 5W-30 oil, select the required fluid according to scheme 3.
Scheme 3. Viscosity index of lubricating fluids for gasoline engines depending on the ambient temperature. According to the scheme should be used:
- 5w - 30; 5w - 40 in the temperature range -30°С (and less) to +40°С (and above);
- 10w - 30; 10w - 40; 10w - 50 at temperatures of -25 ° C to +40 ° C (or more);
- 15w - 40; 15w - 50 at -20°C to +40°C (or more);
- 20w - 40; 20w - 50 at a temperature range of -15°C to +40°C (or more).
Summarize
The recommended engine oil for Nissan Teana can be selected according to the manual for the car. Also in the instructions you can find recommendations on the frequency of changing the lubricant. The manufacturer describes the sequence of changing the lubricant, precautions when performing these jobs at home. The information contained in the instructions makes it possible to increase the operating period of the power unit and the lubrication system.
