The Kalina fuel filter must be checked immediately in cases where it starts to twitch, pull badly, or simply stall for no apparent reason.

Kalina fuel filter - why is it needed and when should it be changed?

Any motorist knows that a vehicle is installed in order to filter the fuel entering the engine with high quality. The gasoline we fill up at gas stations is often contaminated with a variety of particles and water.

A similar situation can be observed even when the driver “feeds” his iron horse at prestigious and expensive gas stations.

Fuel is often contaminated directly during its manufacture, during long-term storage in the manufacturer's warehouses, during transportation to a gas station. Also, some impurities (from the resulting oxides, dust) often get into it in the fuel tank of the car itself. It is clear that low-quality gasoline will sooner or later lead to a breakdown of the car.

To avoid this, it is recommended to replace the fuel filter at the time indicated by the manufacturer, or if the “symptoms” indicated at the beginning of the article occur. So, on the Lada Kalina that interests us, it should be changed after 30 thousand kilometers (if you listen to the recommendations of AvtoVAZ). In practice, the owners of Kalina replace the filter every 10 thousand kilometers.

The procedure for replacing the fuel filter

This event is best done during the warm season. Experienced motorists who do not use the vehicle very actively usually replace the described element twice a year - in autumn and spring. The process is carried out on a flyover or a pit. Before it starts, be sure to relieve the pressure in the system. For this:

• remove the fuse;
• remove the plastic cover located next to the gear lever with a screwdriver, and get access to the fuse box;
• remove the central fuse from the block with tweezers or fingers.

After that, you can start the Lada Kalina and wait (from 5 to 50 seconds) when the "heart" of the car stalls. The pressure dropped. You can safely start replacing the filter, which is located at the rear wheel near the fuel tank. As a rule, it is held by ordinary fasteners. It is not difficult to cope with it: you need to press the latches (pressure from above) and at the same time pull the fuel hoses to the sides, after which the filter can be removed without problems.

In place of the old unit, we put a new Kalina fuel filter. It is important here to install the part exactly as its predecessor stood. The arrow on the filter housing must match the direction of fuel flow.

What to do after replacing the filter element?

Having completed the installation of the new filter, we carefully return to place all the previously unscrewed components, including, of course, the fuse, and try to start the engine. In cases where “the process does not go” the first time, you should not be upset. Having made a couple of attempts, you will increase the pressure indicator in the system, and the engine will work completely.

AvtoVAZ began production of the Lada Kalina model in 2004. The base sedan existed on the assembly line from 2004 to 2011. Now the plant produces two body versions: a hatchback and a station wagon. Many are interested in the question of how the fuel filter is replaced. In this article we will tell you where this filter is located, how to remove the old filter and, accordingly, how to change it to a new one. And you will see that if you strictly follow all the rules, replacing the fuel filter will not be a difficult procedure for you.

How does a fuel filter work?

If we touch upon the qualitative aspects of domestic fuel, then they have long been the subject of many complaints. Note that in this regard, both the manufacturers themselves and the large army of Lada Kalina owners are indignant. Often, in the absence of a choice, you have to pour substandard fuel into the tank of your “horse”. Such gasoline is full of various impurities and abrasive particles, in addition to which there is also water. Among the factors causing fuel pollution, the following can be distinguished:

• storage for a considerable period of time;
• ingress of dirt and dust during transportation;
• reactions of a chemical nature that occur inside the tank, etc.

Abrasive particles can play a trick on the engine, because they, along with the fuel, are sent straight to the combustion chambers. To prevent this negative moment, manufacturers use filters. And you need a timely replacement of the fuel filter on your car. And about where it is located, how to remove the clogged filter and how to change it to a new one, read below.

These components include:

• coarse filters capable of "stopping" particles larger than 0.1 mm; such an element is a mesh with an appropriate mesh size and is located in the fuel pump housing;
• filters designed for fine cleaning; they are capable of retaining smaller particles, the minimum size of which is 0.15 mm; the product is installed in the line between the tank and the motor.

The structural composition of the filter is as follows. A working element is integrated into the metal case, which is made of specialized paper. Operation leads to gradual clogging of various kinds of particles and impurities suspended in the fuel. This provokes the periodic replacement of the filter to be included in the mandatory list of works performed on the car as part of scheduled maintenance. This approach is also valid for Lada Kalina.

Replacing the fuel filter on Kalina

If the filter is heavily clogged, then:

• the motor power indicator decreases;
• increased fuel consumption;
• while driving, jerks and unstable operation of the unit are observed;
• the motor tends to stall.

When the manifestation of these factors becomes apparent, the filter requires urgent replacement. In order to avoid bringing the motor to critical conditions, the regulations provide for the interval (mileage) for periodic filter replacement:

• with regards to the coarse cleaning component - 80-95 thousand km;
• for a fine filter element - 30 thousand km.

Advice! Domestic fuel is not happy with its quality, and therefore we recommend combining filter replacement with work on changing the oil filter component, that is, approximately every 10 thousand km of the distance traveled.

Changing the fine filter

The very process of replacing this component in Lada Kalina is a very simple action and is also included in the maintenance schedule. The most significant condition is to provide access under the bottom of the car, to where the filter itself is located, which may require a lift, overpass or pit.

How to remove the old filter? As a tool, you can arm yourself with a regular screwdriver. This operation will take a maximum of forty minutes.

Information! Some modifications of "Kalina" (for example, "1119", "1186", "21126" and "21127") provide for fastening the filter component housing with a bolt, and therefore, the screwdriver can be safely "changed" to a key with a dimension of "10" .

1. At the very beginning of our "operation" we release the pressure present in the fuel circuit. For this purpose, we open the power supply circuit of the pump. You can perform this action in two ways:

• we take out the fuse with the number "F21", located under the tunnel cover near the gearshift lever (to remove the cover, you will need a screwdriver with a flat "sting");
• disconnect the connector of the fuel supply pump itself, which is located under the rear seat cushion; here you will need to unscrew the 4 screws of the cover and after removing it, access to the connector will be provided.

After turning off the pump, we start the Lada Kalina engine and wait for the fuel to run out of the line, after which we observe a natural stop of the engine.

2. The filter itself is located under the tank and in most versions is fixed with a plastic retainer.

3. Before dismantling the filter, it will be necessary to disconnect the fuel pipes, also fixed with clamps. They should be disconnected, after which the filter can be freely removed.

Attention! The filter, which is fixed near the tank with the help of a combined clamp-bolt fastener, is dismantled using a wrench of the specified size.

4. We install a new element (its catalog code is “2190-1117010”) on a LADA Kalina car between the provided stops and following the reverse dismantling algorithm.

5. We put the previously removed fuel pipes on the corresponding fittings until a characteristic click of the latches is felt.

Important! We carefully study the surface of the filter housing and find a schematic arrow on it, which on the installed component should be oriented towards the direction of the fuel supply.

6. We make sure that the specified fasteners are securely fixed and return the fuse marked “F21” to its original place (or connect the cable harness to the pump block and install the cover).

7. We start the engine. Here you will need a few correct actions:

• turn on and immediately turn off the ignition several times in a row;
• wait a pause for the pump to pump the line with fuel;
• finally start the engine.

Now you know how to change the fuel filter in the car.

When the unit does not fully start on the first attempt, we perform the indicated procedure again. This is necessary to achieve the pressure in the fuel supply system of its working value.

Replacing a component on the fuel pump

This procedure is characterized by complexity and genuine laboriousness. Here you will need a lot of experience and skills of the owner of LADA Kalina.

In conclusion, about precautions when replacing

Compliance with the rules to ensure safety in this procedure is exceptional. Even following the utmost care during work, it is impossible to absolutely exclude the release of flammable compounds and the spillage of fuel. Otherwise, replacing the fuel filter on a LADA Kalina car is not a difficult procedure.

To prevent the risk of ignition of fuel vapors, it is necessary:

• the entire list of manipulations should be carried out in conditions of good ventilation of the room or in an open area;
• Spilled fuel should be eliminated immediately with a rag or backfill with sand;
• follow the rules for using portable lighting devices;
• stock up on a fire extinguisher;
• do not smoke during this repair process;

Remember to use gloves and goggles to avoid the risk of getting fuel on your hands or eyes.

In our time, a car is “not a luxury, but a means of transportation”, as they say in the unshakable classics. Therefore, for the normal operation of a vital device, constant care and regular replacement of certain parts are required.

What is a fuel filter for? ? The fuel filter in the car exists in order to filter and clean the fuel supplied to the engine from foreign particles. How does a fuel filter work? The fuel you fill your car with may contain small debris, pieces of rust, water, dust, oxides and other “junk”, which at any time can lead to malfunctioning of the engine if it is not filtered out in time. Even drivers visiting elite gas stations and using expensive gasoline are not immune from such a nuisance, since the appearance of such undesirable impurities depends not only on the quality of the fuel and its manufacture, but also on its transportation, storage and other processes that sometimes cannot be controlled. From this we can conclude that the fuel filter must be present in every car.

what is a fuel filter for, how does a fuel filter work

From time to time, the fuel filter needs to be replaced, so many are interested in the question, how often to change the fuel filter on viburnum? The frequency of this procedure in a particular machine is indicated by the manufacturer. According to AvtoVAZ recommendations, the filter should be replaced after the run 30 thousand km , however, in practice, this manipulation has to be performed much more often, approximately every 10 thousand km. Signs of a bad fuel filter: if you feel a problem with the engine, for example, the car began to twitch while driving, pull badly or stall for no reason, in this case, it is likely that the car needs to replace the fuel filter. So now you know why you need to change the fuel filter and when you need to change the fuel filter on viburnum.

Don't hesitate to replace! But what happens if you do not change the fuel filter and how it will affect the operation of the car. After 40 thousand km Filter operation almost stops, and gasoline becomes black from all kinds of impurities. Therefore, the inattention and recklessness of an inexperienced motorist can lead to completely unforeseen troubles, the cause of which will be quite difficult to determine.

Replacing the fuel filter Lada Kalina

Most often, experienced motorists replace the fuel filter in the warm season, since vehicles are used less frequently on winter days. Spring or autumn are just the right seasons for this process. Replacing the Lada Kalina fuel filter in the spring-summer season will help get rid of the condensate accumulated over the winter, and if you take care of it also in the fall, then the summer condensate water will not be able to freeze in severe frost. This process will be most conveniently carried out in a car dealership, on a garage overpass or pit.

Before replacing, relieve pressure in the system:

• Remove the fuel pump fuse;
• Using a screwdriver, remove the plastic cover near the gearbox;
• Among the three fuses, you need to get the central one. If you can't do this with your fingers, use tweezers.

When it's all done start the car until the engine stops , it will take five seconds. If it took you longer (about a minute), there may be an air lock problem. However, stopping the engine means that the pressure in the system has dropped. Now you can start replacing the fuel filter:

1) Push in the retainers while pulling on the hoses. However, you may need key for 10;

2) Remove the fuel filter;

3) Install a new filter.

Note: Who doesn't know . This part of the mechanism is located between the gas tank and the carburetor (near the rear right wheel) and most often rests on just one fastener, so replacing it is a simple process.

signs of a bad fuel filter, why change the fuel filter

It is important to replace the fuel filter on the Lada Kalina in exactly the same place and in the same position as it was before. There is an arrow on the filter housing, which must coincide with the direction of the flow of gasoline. Tip: before replacing the fuel filter, treat all fasteners well so that you do not have difficulty unscrewing them later.

Starting the engine after replacing the fuel filter

So you have succeeded in replacing the fuel filter on viburnum, and you know how to change the fuel filter correctly. Now carry out reverse manipulations to return the unscrewed parts. Made? Start the engine. Don't panic if it doesn't work the first time. In order to increase the dropped pressure in the engine, at least two or three attempts will be required. After that, the machine must work. If you are a beginner motorist, here is a small instruction:

• Try to ignite a couple of times;
• If it doesn’t work, wait a few seconds until the fuel pump pumps up the required amount of fuel;
• Now you can start the engine.

Ready! As you can see, this is a fairly simple process that takes a maximum of half an hour and will not cause difficulties even for inexperienced motorists. Moreover, all the manipulations can be done independently, without contacting a car service. And this, after all, savings! Well, if you are still unsure of your abilities, you can turn to professionals.

Certainly, there are innovators, which manage to use the same filter multiple times , by cleaning it, but it is worth noting that this method is not safe for your car and it is best to make a complete replacement of the fuel filter. Moreover, this is a fairly mundane and inexpensive process, so it's not worth the risk and it's better to buy a new fuel filter.

For a memo: try to refuel only at proven gas stations and give preference to more expensive, elite brands, since low-quality fuel, and, accordingly, the operation of the fuel filter affect the performance of your car. So now you are savvy, you know where the fuel filter is located on the Lada viburnum and, accordingly, how to change the fuel filter on the viburnum step by step.

If you liked the article, share it on social networks and leave comments!

The filter element in the fuel system of a Toyota Corolla plays a very large and important role. It removes various mechanical particles and condensate from the fuel, which ensures the normal operation of the engine for a long time. The design of the fuel filter for Toyota Corolla differs from similar samples for many branded models. In addition, the structural features of the filter module still largely depend on the modification of the car body. So, for example, Corolla cars in the 150th and 120th bodies of 2007 and 2008 have a different types of fuel pump and filter, which does not affect the principle of their replacement, which is identical.

In this article, we will share with you information about the filter in the original design and the frequency of its replacement. You will learn about all types of fuel filters for the Corolla on the Russian market and read the step-by-step instructions for replacing them.

The frequency of replacing the fuel filter on the Toyota Corolla

The replacement of the fuel filter according to the operating instructions must be carried out every 80 thousand kilometers. Many car owners drive without changing the filter, thereby almost doubling the recommended mileage. It is impossible to deal with the fuel system and the engine in this way, because it is no secret that the quality of domestic gasoline is much inferior to the Japanese standard. Therefore, keep in mind that the fuel filter, like any other cleaning element, cannot last forever and its resource is limited by the car's mileage or a certain time interval. Maintenance specialists strongly recommend replacing every 50 thousand kilometers. However, the replacement of the fuel filter may be required earlier. Certain signs will indicate this to you.

Signs of a Clogged Fuel Filter

Many Toyota Corolla car owners start replacing the filter only if there are clear signs of a decrease in the throughput of the cleaning element or if the engine has completely failed. Since the clogging of the filter occurs at a slow pace, it is far from immediately possible to notice the obvious symptoms of its poor performance. And further operation with a clogged filter negatively affects the overhaul period of the engine, which is reduced.

We list the main signs of a clogged filter:

• Uneven engine operation both at idle and under load
• Slow acceleration
• Unstable engine start
• Unexpected engine stalls

T Types of fuel filters for Toyota Corolla in the Russian automotive market

Many car dealerships offer a choice of at least three types of products of this type for Toyota Corolla. First of all, these are products from Chinese and Korean manufacturers, as well as the original version. Many motorists do not believe that the quality of different types of filters varies greatly. The main thing is to correctly install the sealing gaskets that come with them in the kit when replacing the filter.

Depending on the modification of the Toyota Corolla car body and the year of manufacture (before 2007 or after), you should individually select a fuel filter that is suitable for its design. There are designs of fuel supply units from a gas tank, where the filter is located in the pump itself, which is why the replacement has to be carried out as a whole module. The procedure is expensive, but the car owner still has no choice. Unlike these Toyota models, Corolla cars produced in 2008 were equipped with other fuel filter designs that can be completely replaced and installed separately from the fuel pump.

A rich assortment of foreign spare parts allows the motorist to make his choice on the line, on the one hand of which is the cost of the product, on the other - a high quality standard of replacement parts. For example, the price of individual copies exceeds about 10,000 rubles. This is especially true for products of the original design, which are completed from non-separable blocks of the filter and pump.

Fuel filter replacement for Toyota Corolla 120 body

So, before replacing the fuel filter, be sure to familiarize yourself with the fire safety regulations, as well as stock up on the necessary tools and spare parts.

Fire safety during work

When working with the fuel system, compliance with fire safety regulations is a necessary requirement. The penetration of gasoline vapors begins within a few seconds after removing the gas tank cap. The mixture of air and fuel is highly explosive, so there should not be any open sources of fire nearby!

After removing the pump unit, when work is being done somewhere on the table, the gas tank neck must be temporarily covered with a dense layer of material: a clean film or cloth. At the same time, do not close the car doors, as the interior will be ventilated through them. By the way, it is much better if the work on replacing the fuel filter is carried out in the open air.

Toyota Corolla fuel filter replacement tools

• Canister for draining gasoline
• rags
• New filter. An original cleaning element for the Corolla will cost 4,000 rubles, while a Chinese-made filter will cost 2,500 rubles.
• Two sealing rings for 200 rubles.
• Flat screwdriver
• crosshead screwdriver
• Vacuum cleaner

Step-by-step instructions for replacing the fuel filter on a Toyota Corolla body 120

• Access to the Toyota Corolla 120 fuel filter is by removing the rear passenger seat on the left side of the passenger compartment.

• Next, remove the upholstery of the bottom of the body, located under the seat. To do this, use the key to "10" to unscrew the two fasteners (red arrows). Remove the piston with a screwdriver (yellow arrow).

• Raise the seat mat. We fix it with driver and passenger seat belts for the red ledges. Under the rug we see a layer of foam, which should be dismantled.

• Now your eyes will see the fuel pump cover, which can be carefully pry off and removed with a knife or a flat screwdriver (it sits on black sealant).

• Before proceeding directly to the replacement, you should thoroughly vacuum the cavity that has opened, first under the rug, and then above the gas tank.
• Before disconnecting the pipes, we substitute a pre-stored canister to drain the remaining gasoline. Next, remove the fuel lines. The small pipe or return hose can be removed very easily, just pull the yellow bracket to the side with a thin screwdriver. Disconnecting the second hose will also not take much effort, however, in which case you can also help yourself with a screwdriver.

• Before directly dismantling the fuel filter, when the pipes are pulled out, the car must be started and wait two or three minutes until it stalls itself. As soon as the engine turns off, you can crank the starter a few more times. This process will remove all fuel from the system, as well as release pressure.
• Next, you need to disconnect the battery terminals.
• Next, unscrew the eight screws with a Phillips screwdriver or an “8” key and remove the pump unit. Rags will come in handy here, as gasoline will flow out of all the cracks.

• To get to the fine filter and replace consumable components, we proceed to disassemble the fuel pump.
• Remove the latch to disconnect the float.

• Next, in a circle, we press on the plastic clips to disconnect the block body in the upper part.
• We make a small effort to pull the fuel pump out of the rubber seal.

• We insert the fuel pump into the new fine filter housing.
• Then you should rinse and blow the intake mesh with compressed air and assemble everything in the reverse order.

If you make the replacement in accordance with all the rules and do not forget the rubber o-rings, the engine will start without problems and will work better than before.

Replacing the fuel filter on a Toyota Corolla body 150

Another modification of the Toyota Corolla model with a 150 body manufactured in 2008 has a large plastic ring with a rubber seal instead of a metal gas tank cap. To remove the block, the ring must be turned counterclockwise to loosen the seal. You can unscrew the annular lid using wooden chopsticks, which should be pointed at the ribs of the lid and carefully beat them with a hammer. With further disassembly, some parts may differ from the design of the Toyota Corolla with a 120 body until 2008. For example, the intake mesh and the fine filter look a little different, otherwise everything is almost the same. In general, the replacement process is identical, so you can use the above instructions for Toyota Corolla with a 120 body.

Conclusion

The Toyota Corolla fuel filter should be replaced in a timely manner, in accordance with the manufacturer's recommendations. You should not wait until the car becomes faulty - after all, all its systems are inextricably linked. If breakdowns begin due to a clogged filter, then you will have to spend money not only on replacing the cleaning element, but also on expensive diagnostics, coupled with repairs.

We draw your attention to the following video, which clearly demonstrates all the stages of replacing the fuel filter on a Toyota Corolla 120:

The quality of gasoline in our country leaves much to be desired. And quite often it even happens that after refueling at a proven and prestigious gas station, the car engine starts to work intermittently.

This can be caused by all sorts of impurities, such as water, and other debris that can clog your car's "nutrient :-)" system.

According to the manufacturer's recommendation, the fuel filter on the Lada Kalina should be replaced after 30,000 kilometers. Of course, I delayed this procedure a little on my car, since the speedometer is already a little over 40,000 km, but recently I decided to do a replacement. I bought the simplest fuel filter from the AvtoVAZ manufacturer in a car shop, exactly the same as it is installed at the factory. The price is reasonable, only 146 rubles.

A detailed guide to replacing the fuel filter on the Lada Kalina

I would like to say right away that this repair is best done in a pit, and in the warm season. I was less fortunate and had to suffer in the winter, lying under my Kalina, to change this fuel filter. But some time later, it turned out to record a video report in normal human conditions, so look at this whole procedure clearly.

Fuel filter replacement video

This video review was made in a garage with a viewing hole, so everything is shown in the most understandable and accessible way.

Well, below is the classic version in the form of a photo report!

So, the first step is to ensure that there is no pressure in the power system. This is done in two different ways, which one will be more convenient for whom:

You can remove the fuse, which is responsible for the operation of the fuel pump. It is located under the floor tunnel cover, just near the gearshift lever. The cover is removed by lightly prying with a flathead screwdriver.

There is a small block, which consists of three fuses. It is necessary to extract the central one, and to be more precise, the second one on the left side.

The second way is to disconnect the power plug from the fuel pump. This can be done by tilting the rear seat, then open the fuel pump cover and disconnect the block with the wiring harness.

After completing the procedure you have chosen, we start the Kalina engine and wait until the engine stalls. This usually happens very quickly, within half a minute in my case.

Directly the fuel filter of Lada Kalina is located under the fuel tank. To make it easier for you to understand: on the right rear side of the car.

The fuel filter is fixed quite simply, as you can see in the photo I have given - just with the help of a plastic retainer, the so-called bracket or clamp. But the fastening of the power fittings to the filter itself occurs due to metal clamps. To remove the fuel hoses, you need to squeeze out these brackets on each side and pull on the fittings. After that, you can remove the filter itself, this is clearly shown in the photo below:

Before installing the fuel filter, pay attention to the arrow that is drawn on the body. It should be directed in the direction of the movement of fuel along the highway. In short, the arrow should go from the tank to the engine compartment of the Lada Kalina. Installing a new filter is very simple, we insert the fittings to each end of the fuel filter and press it all the way - that is, until we hear a characteristic click.

If everything is carried out on a raised car or in a pit, then you can probably do it in 10 minutes. If you suffer as much as I did, then I think that you will fiddle around for about half an hour for sure. In winter, it is not very pleasant to do this, especially when lying on the snow.

After replacing the fuel filter, insert the fuel pump fuse back or connect the plug. Then we start Kalina and rejoice, now the power system will be protected from any rubbish and the injector will work as expected. The main thing is to change this element in time.