Engine oil Skoda octavia a7 1.8. What oil is better to pour? Why such an excellent appetite

31.07.2023

Dilemma of the 21st century: What kind of oil to fill in a 1.6 mpi engine in a Skoda Octavia A7? In 2014, an updated line of Skoda Octavia A7 cars with atmospheric 1.6 MPI engines began to enter the car markets. Now the engine belonged to the EA211 series and received the CWVA index.

Its special characteristics lie in the following:

Lightweight aluminum cylinder block
Double-circuit cooling model
Excluded intercooler, injection pump, compressor
The presence of pistons of increased diameter
Distribution injection system installed

Why such an excellent appetite?

But when answering the frequent question “What kind of oil to fill in a 1.6 mpi engine in a Skoda Octavia a7?”, Other features are important, namely:

Small piston ring toast
Small mass of pistons
Low piston height

Thanks to this lightening of the power unit and the reduction in the size of some parts, friction inside is reduced, which in turn leads to saving gasoline and minimizing harmful substances in the exhaust. Everything would be fine, whenever it was so sad. Due to the occurrence of large gaps between the components of the motor, the "oil burn" increases.

At the same time, the “fragile” cylinder-piston group copes worse with increased loads, having special requirements for the quality of the lubricant consumed. The CPG overheats under “stressful” conditions, the compression apparatus and oil scraper rings do a worse job and much more lubricant enters the cylinder. When burned, carbon deposits settle on the pot and piston skirts.

In general, the design that affects the increased consumption of lubricating fluid includes: poor tension of the oil scraper rings, the surface of the cylinder walls that is “beneficial” for depositing carbon deposits, design flaws when converting a turbo engine to an atmospheric one.

How to reduce consumption?

A few obvious rules that the owner of the EA211 line unit cannot do without:

Periodically check the oil level in the cylinder. And immediately contact the service, with its imminent fall. However, remember, the German concern warns that the consumption of motor lubricant in this engine is one liter per 1000 km. Therefore, it seems like 4 liters per 4000-5000 km is the norm.
Eliminate stressful modes for your iron horse - traffic jams, sharp driving in hot weather
Change the lubricating fluid based on the hours worked and the actual condition. In order not to constantly perform complex calculations on the calculation of hours, rely on the data of the on-board computer. Or divide the mileage since the last lube change by your average travel speed. If the indicator is equal to or higher than 300 hours, it's time to change. In Russia, with its "extreme" conditions, this is about 7-10 thousand km. mileage
Use lubricants with improved cleaning properties and low carbon monoxide. Better yet, consider options from recommended manufacturers

Note that the less often you plan to change the lubricant of the power unit, the more fluid at high temperatures it should be and less viscous. So it is assumed that when using a more viscous oil product, which forms a thick film on the parts, it is necessary to modify it more often. And when using a less viscous fluid, but specification 504, replacement may be less frequent.

A little about permissions

Reading articles and reviews on the topic “What kind of oil to fill in a 1.6 mpi engine in a Skoda Octavia a7”, one cannot help but pay attention to the frequent dispute between tolerances 502 and 504. In addition, the price of a lubricant with these different indicators within one manufacturer may differ in times. What is the difference between them. Should I blindly follow the manufacturer's recommendations?

Permission 504, unlike 502, provides for:

Increased compatibility with exhaust gas treatment systems due to reduced ash content
Better prevention of deposits on pistons and filters
High-quality wear protection (up to 400 hours under difficult conditions instead of 250 hours for 502)
Synthetic base (improved winter performance)

However, there are also disadvantages of 504 specifications before 502:

Sensitive to low-quality fuel, severe operating conditions (gas-brake trips, short trips, idling in cold weather, dusty areas, etc.)
Limited viscosity ratings (only 0w30/5w30)
Evaporation less than 11% (against 16% for 502) - the higher the volatility, the less waste
Low ash formulation with low base number

In general, the conclusion is this: resolution 502 has a larger range in composition, in viscosity levels, with certain tests by manufacturers, it can increase the life of a lubricating oil product up to 350 hours (18 thousand km). And the undoubted advantage of 502 specifications is its favorable price compared to 504. To be more specific: the quality of 502 and 504 series from different manufacturers can either differ or match. Therefore, the 502 specification is not always worse than the 504 - it is necessary to compare the preferred bottles.

Pedestal of the best

From the foregoing, we can conclude that when choosing a lubricant for the car in question, you can fill in both 502 resolution and 504, depending on the manufacturer, and on what principle you are ready to live:

Change more often (every 7-10 thousand km), but take the cheapest.
Change less often (every 15-30 thousand km), but take expensive.

Provided that car owners have the same requirements for the assistant lubricant - ensuring decent protection of parts for the inter-shift period, resistance to winter adventures, reasonable price, 502 tolerance is more than suitable. In our non-professional opinion, based on our own experience and the opinion of several hundred motorists, it is better to prefer specification 502 engine oil, and refill it every 7000 km.

The following brands will be optimal in terms of price and quality:

Addinol Super Power MV 0537

Shell HX-8 Synthetic

Liqua Moli Special LL

If you are not a supporter of often climbing under the hood, or decide to play it safe, especially in winter, then choose specification 504 and brands:

Amsoil European Car Formula
Total Quartz INEO Long Life
Shell Helix Ultra ECT
Likva Moli Top Tech 4200
Castrol Edge LL
ssangyong
Zeke XQ TOP

And now the answer is yours: “And what kind of oil do you fill in the 1.6 mpi engine in the Skoda Octavia A7?”. Compare, experiment, go for it!

Skoda Octavia A7 is a modern middle-class liftback that is very popular on the Russian market. There is a high demand for the machine, which confirms its high quality and reliability. However, many motorists are unhappy with the high cost of maintaining the Skoda Octavia A7. Therefore, it is not surprising that Russian owners prefer to service the car on their own, especially if the car warranty has expired. Here we are not talking about some complex procedures such as repairing a gearbox or internal combustion engine. Oddly enough, against the background of these complex works, the choice of high-quality oil for the Skoda Octavia engine will be no less important. This issue is now quite relevant, and deserves special attention.

Where to begin

Before choosing the first brand that comes across and listening to the marketing tricks of sales consultants, first you need to study the instruction manual from the Skoda Octavia A7. First of all, the car owner should be interested in the parameters and certain tolerances that must be referred to when choosing the right fluid. For example, for a 1.6 gasoline engine, the engine oil specification should look like this: WV501 01, VW502 00. Based on these data, you can purchase liquid from any well-known brand.

Skoda Octavia A7 leaves the factory assembly line with Castrol EDGE oil filled in. This is the best option for this model. According to statistics, about 43% of Skoda car owners prefer this oil. The liquid in question has gasoline-atomic characteristics that are ideal for almost the entire Skoda Octavia engine line.
In addition, when choosing the right fluid, you need to take into account the license plate, by which you can determine the correspondence to the roughness of the piston rings. If there is no correspondence, this can lead to premature wear of the piston rings, and as a result, a major overhaul of the power plant will have to be done. This is a rather laborious process, which is unlikely to be mastered by an inexperienced owner.

Why Castrol

There are many reasons for this. The products of this manufacturer are most suitable for the characteristics of the Skoda Octavia A7 engines. But here, too, there are important nuances. For example, Castrol has certain temperature parameters. But in any case, to be sure of the quality of the products on the product packaging, you need to pay attention to the corresponding markings: ACEA A3 / B4, as well as API SL / CF. Based on this information, it is possible to isolate oil with suitable parameters: for example, Castrol EDGE 0W40 A3 / B4.

How much to fill

The volume of the original oil poured into the Skoda Octavia A7 engine is 4.5 liters. Please note that the liquid should be poured gradually. If there is an overflow, then this can lead to undesirable consequences, up to an explosion under the influence of high temperatures in the summer. In this regard, you first need to fill in about 4 liters, and then look at the circumstances. You can leave an empty space at the top, which will subsequently be filled with cold air. This air, in turn, will circulate and cool the engine components.

Analogues

— new Skoda oil recommendations in Russia,
- specification and recommendations from the manual,
- which oil is better and what the dealer pours,
- when to change the oil,
- volume of oil to be replaced,
- checking the oil level on the dipstick,
- what is better draining or pumping out - video,
— original vag oil — cat.number.

Often there are the following questions, answers to the cat. dealers gave me:

What kind of oil does the manufacturer pour into Skoda?- Shell helix / Castrol.
What kind of oil do dealers pour us?- with whom the contract is concluded, then they pour. Basically Castrol.
What oil is better to pour?— be guided not by reviews, but by the recommendations of the factory and the condition of your car.

My experience.
Previously, I poured LiquiMolly 5W30 TOP TEC 4200 LongLife III oil - the consumption was about 500 grams per thousand.

UPDATE 01/14/16
Now I switched to Shell Helix Ultra 0w30, tolerance 502 - consumption has decreased!
It was about 200 grams per thousand.

given in this letter

Specifications for oil from the Skoda owner's manual

When topping up, you can mix different oils with each other. This Not applies to vehicles with flexible interservice intervals.

Filling volumes are given taking into account the replacement of the oil filter. Check the oil level when filling, do not fill too much.

For vehicles with flexible service intervals Only the following oils may be used.

To maintain the properties of the engine oil, we recommend topping up with oil of the same specification only. In exceptional cases, it is possible, only once, to add no more than 0.5 liters of engine oil of specification VW 502 00 (only petrol engines) or specification VW 505 01 (only diesel engines).

Do not use other engine oils - risk of engine damage!

When to change oil

In severe operating conditions in a large city or very dusty areas Recommendation for changing the oil and filter every 7 - 8 thousand km.

Checking the oil level

The vehicle must be on a level surface and the engine must be still warm after operation.
- Stop the engine.
- Open the hood.
- Wait a few minutes for the engine oil to drain back into the oil pan and remove the dipstick.
- Wipe the oil dipstick with a clean cloth and insert as far as it will go.
- Remove the oil dipstick again and check the oil level.

Oil level in zone A- Do not add oil.
Oil level in zone B- You can add oil.

The oil level may then rise to zone A.
Oil level in zone C- You need to add oil.
It is sufficient that the oil level is in zone B.

Engine oil consumption is normal. Depending on driving style and operating conditions, oil consumption can be up to 0.5 l/1000 km.

In the first 5,000 km, oil consumption may be even higher.
It is therefore essential to check the oil level regularly, preferably at every fill-up or after a long drive.

When the engine is under heavy load, such as long motorway driving in the summer, when driving with a trailer or driving in high mountains, it is recommended to keep the oil level in zone A - but not higher.

If the oil level is insufficient, the control lamp in the instrument cluster lights up. In this case, check the oil level with the dipstick as soon as possible. Add the appropriate amount of oil.

CAREFULLY
The oil level must never be higher than zone A.
Risk of damage to the exhaust gas aftertreatment system!

If in this situation you cannot add oil, do not continue driving. Stop the engine and seek professional help, otherwise serious engine damage may result.

Adding engine oil

Check engine oil level » see above
Unscrew the engine oil filler cap.
Pour in oil of the recommended brand in portions of 0.5 liters.
Checking the oil level.
Carefully screw on the oil filler cap and insert the oil dipstick as far as it will go.

Do not add additives to engine oil- this can lead to serious damage to engine parts! Damage caused by such causes is not covered by the warranty.

Useful oil change tips

Drain the oil after driving while the engine is still warm. If the engine is cold, start and warm it up to operating temperature. Fill with the same brand of oil as the oil that was in the engine.
If you still decide to change the brand of oil, flush the lubrication system with flushing oil or oil of the brand that will be used. To do this, after draining the old oil, fill in new oil to the lower mark on the dipstick. Start the engine and let it idle for 10 minutes. Drain the oil and only then change the oil filter. Now you can fill in new oil to the required level (up to the top mark on the dipstick).

How to change the oil and oil filter

Oil change - what is better to drain or pump out

there is no Skoda, but the essence is the same.

Original vag oil - cat.number

Synthetic engine oil Special C
SAE 0W-30
VW 502 00 / 505 00
Catalog number - G 055 167 M2

Other original ones, we can come in handy for someone, found on the drive

G 052 167 M4 - VAG Special Plus 5W-40 - 5 liters (Tolerance: VW 502 00 / 505 00 / 505 01)
G 052 167 M2 - VAG Special Plus 5W-40 - 1 liter (Tolerance: VW 502 00 / 505 00 / 505 01)
G 055 167 M4 - VAG Special C 0W-30 - 5 liters (Tolerance: 502.00/ 505.00/505.01)
G 055 167 M2 - VAG Special C 0W-30 - 1 liter (Tolerance: 502.00/ 505.00/505.01)
G 052 183 M4 - VAG Longlife II 0W-30 - 5 liters (Tolerance: VW 503 00/ 506 00/ 506 01)
G 052 183 M2 - VAG Longlife II 0W-30 - 1 liter (Approval: VW 503 00/ 506 00/ 506 01)
G 052 195 M4 - VAG Longlife III 5W-30 - 5 liters (Tolerance: VW 504 00/ 507 00)
G 052 195 M2 - VAG Longlife III 5W-30 - 1 liter (Tolerance: VW 504 00/ 507 00)

Quite often, the owners of the Skoda Octavia A5 and A7 wonder about the frequency of changing engine oil in their car, as well as how much and which one is better to pour. Also, the owners of these cars are concerned about oil consumption during operation. In this article, we will answer all questions regarding our own oil change, as well as its choice, and we will touch on the topic of repairing the level sensor in the engine crankcase.

First, a little about motors

Skoda Octavia A5 and A7 cars were equipped with 1.4, 1.6 and 1.8 liter engines, the injection systems on these engines were called mpi and tsi. Reliability and ease of maintenance have a positive impact on the reviews of the owners. Repair of these units becomes necessary after 300 thousand kilometers, and this is a considerable resource.
Few characteristics:

The Skoda Octavia A7 1.4 tsi engine is turbocharged and has a power of 140 hp.
The Skoda Octavia A7 1.6 mpi engine is equipped with point injection, and its power is 110 hp.
A 1.8 tsi engine was installed on the Skoda Octavia A5 Tour model; with the help of a turbine, this engine has a power of 152 hp.
The same power unit was installed on the A7 Tour model and has more power - 180 hp.

The choice of oil for cars Skoda Octavia

As we know, the oil change interval is 10 thousand kilometers, only at such intervals the engine of your Skoda Octavia A7 Tour will serve you for many kilometers without breakdowns. Of course, such reliability will be achieved if original solutions for Skoda Octavia are used.

Skoda Octavia 1.6 and 1.8 tsi engines are very picky about the quality of the oil, in order to answer the question of what kind of oil to fill in, we will give some tolerances regulated by the manufacturer.

VW 504
VW 502

It is these tolerances that must be indicated on the label of the canister with the new liquid. When using high-quality fluids, Skoda Octavia 1.6 engines - 110 forces and 1.8 will last more than one hundred thousand kilometers.

If low-quality materials are poured, lubricant consumption can increase significantly.

So that you know which oil is better to pour, we will answer - the original one. It is the original lubricant that performs its functions in the best possible way, thereby protecting engine parts from increased wear.

Getting Started

To get started, we need a certain set of tools, which consists of a set of screwdrivers, as well as socket heads for 13 and 17 millimeters and a ratchet.

To carry out such work, it is necessary to use a viewing hole or a car lift.
Unscrew the oil filter using a special puller, then install a new filter and tighten it.
Dismantle the plastic crankcase protection, then unscrew the drain plug and wait until all the liquid has drained into the container.

It is advisable to carry out this work on a warm engine, since the viscosity of the lubricating fluid decreases, thereby increasing its fluidity.

Screw the drain plug, then mount the crankcase protection in place.
Fill with fresh liquid, observing the level. Carefully check the level and limit the amount of oil poured. To know how much to pour, you must use the dipstick. This dipstick has divisions, on many cars the distance between the minimum and maximum is one liter.
Tighten the filler plug, then start the power unit and make sure that the lubrication system pressure lamp goes out.
Stop the engine and check the level again using the dipstick. If necessary, add liquid in small portions. Using this method, you will have better control over the amount of fluid being poured, and subsequently you will know how much lubrication your motor needs.
If the liquid is at the minimum mark, it is necessary to pour about 400 milliliters, this should be done in several steps, filling the entire volume.

As soon as the level has reached a mark between the minimum and maximum, you should stop pouring liquid and this work can be considered completed.

Attention! If the engine of your car eats oil, you need to set the level to the maximum mark, and then carefully control the volume.

Solving problems with leakage and lubricant consumption.

If you find that your car's engine is eating grease, and the level is decreasing, you need to inspect the unit for leaks. Perhaps the volume sensor has become unusable and needs to be replaced.

Repair of the level sensor is not possible due to its design features. On motors A7 1.4, 140 forces, this malfunction occurs quite often. Therefore, owners of a 140 horsepower engine often complain that the motor eats grease, about 400 milliliters per 1000 kilometers. Do not be upset, you need to immediately inspect the crankcase for leakage of the level sensor, most likely the problem is in it.

In general, Skoda Octavia A7 1.4 tsi engines - 140 forces have a factory approval for lubricant consumption in the amount of 200-400 milliliters per 1000 kilometers. This consumption depends on the driving style of a particular driver, as well as the operating conditions of this vehicle.

To reduce lubricant and fuel consumption, A7 1.4 tsi - 140 hp motors should not be subjected to extreme loads. Moving smoothly without sudden accelerations, you will not only reduce lubricant consumption, but also protect your car from increased wear of rubbing parts.

Sensor repair

On engines Skoda Octavia A7 1.4 tsi - 140 forces, as well as 1.6 mpi - 110 forces, the level sensor must be replaced in case of damage. The same picture is observed on a 1.8 liter unit. Of course, there are some cases in which repair makes sense.

To change this sensor, it is necessary to pour all the grease from the engine crankcase until it flows out completely, after which, having disconnected the connector, unscrew the three bolts securing this part in the desired position. After removing the sensor, it is necessary to thoroughly clean the contact surface, then install a new part and fasten it.

After installing a new part, it is necessary to replenish the amount of lubricant again.

This procedure is best combined with a scheduled oil change in the engine. After replacing this element with a Skoda Octavia A7 1.4 tsi - 140 forces, as well as 1.6 mpi - 110 forces, the lubricant consumption will decrease significantly, and you will not have to constantly pour decreasing lubricant.

In the event that the motor eats grease after replacing this part, most likely, it will be necessary to repair the entire unit. Perhaps the lubricant eats precisely because of the increased wear of the piston rings. Also, the motor eats grease after overheating or eats due to failure of valve seals. All these reasons can be at the same time, and then the power unit eats grease in huge quantities. A comprehensive repair of the power unit is comparable to half the cost of the entire car, and this is a considerable expense of finance.

Conclusion

How do we know the engines of Skoda Octavia A7 and A5? such as 1.4,1.6,1.8? with a capacity of 110 to 140 horsepower, they are quite reliable units. With proper maintenance and regular maintenance, these engines are capable of running 300,000 kilometers without repair.
To know which lubricant is better to pour into the motor, you need to purchase original solutions and be guided by the manufacturer's approval. In this case, the resource of your car will remain the same as it is provided by the manufacturer.
We described in detail how to replace the engine fluid. You can be guided by our article and perform step-by-step actions, referring to each item. Pay due attention to safety regulations.
If your car's engine is eating grease, you need to inspect its body for leaks. If the level sensor is damaged, the repair of this device is impossible, the manufacturer provides only a replacement. How to replace this element, we described in detail in our article.

Changing the oil and filter of the Skoda Octavia A7 is a fairly new concept, because it has recently appeared in the vastness of our country. Our website has prepared detailed instructions on this subject, which is contained in this article.

How to choose oil

When choosing oil, the car owner is divided into two categories:

only original and expensive;
should be found cheaper.

When choosing an oil and filter, it should be borne in mind that you need to pour into the engine only with the same marking and preferably the original, while the car is at the break-in stage. If not, then you need to thoroughly rinse it and replace it with another manufacturer without changing the viscosity. That is, if synthetics were flooded, then synthetics must be poured.

The original oil, which is filled in the Skoda Octavia A7, next marked "Longlife III 5W-30" and has a catalog number VAG G 052 195 M4. According to these data, you can easily choose an analogue.

How to choose an oil filter

The choice of an oil filter depends on how much money the owner has. Who can afford to put the original, he installs it, if he cannot, then he puts others similar.

The table below shows the catalog number of the original filter, by which you can select analogues that are already listed in the "analogues" line.

Name	Catalog number	Analogues
Oil filter	VAG 04E 115 561H	Alco SP-1384, Bosch F 026 407 143 Filtron OP 616/3, Knecht (Mahle Filter) OC 977/1, MANN FILTER W 712/95, WIX WL7503

Oil change process Skoda Octavia A 7

Now let's look at the step-by-step process of changing the oil and filter in the Skoda Octavia A7 engines.

We are looking for a set of tools that is suitable for replacement.
Now we buy oil and filter.
We put the car in a pit or in another similar position.
We unscrew the engine protection - metal and plastic.
Unscrew the oil drain plug and wait for the oil to escape.
Using a special puller or grip, remove the filter.
Now we twist the new filter and oil drain plug.
Pour new oil through the filler neck.
As with all cars, you should start and let it run, and then add oil.

Conclusion

Changing the Skoda Octavia A7 oil, like on all cars, is quite simple. By following the instructions and selecting high-quality oil and parts, your engine will last a long and decent life. If problems arise due to self-changing the oil, you should contact specialists who will help to cope with it.