Self-installation of the radio in the Ford Focus. Car radio for Ford Focus: everything you need to know

Radio for Ford Focus 2

In this article, we will learn all the advantages of a Ford head unit and how to install it. The car radio for Ford Focus 2 is easy to mount with your own hands, if you know the basic rules and nuances.
Car radios for Ford Focus 2 have a good set of additional accessories that come with it.

Installing the radio

Note. To begin with, remember that the car radio will be installed in the same place where the factory one stands. If the car does not have a radio at all, then to the place intended for this in the panel.
No additional frames or chips are needed, because the head unit cover completely repeats the curves and shapes of the intended place. In addition, the regular car radio fits perfectly into the overall interior.

We also note that there will be no difficulty. It is not necessary to contact the service, where they charge a lot of money for the operation. Installation will take only half an hour of time, even including the analysis of the torpedo.
It is enough to be a person who at least once fixed the outlet in the house or repaired the tap:

• We arm ourselves with the necessary tools: plastic rulers and a curly screwdriver.

Note. Rulers can be any, plastic or wooden. Suitable, for example, kitchen spatulas for Teflon dishes. As for metal rulers, it is not recommended to use them, as they can inadvertently scratch the overlay panels.

• We insert the rulers (there should be 4 pieces) into the gaps between the torpedo and the frame that goes along the circumference of the car radio. This is not so easy to do, because the Ford Focus is a car that is assembled with high quality and the gaps are minimal. But having inserted the first line, things will go easier further.

• We insert all 4 rulers (more are possible) in order to prevent the lining from being skewed during the replacement process.
• Gently bend the trim from the torpedo. It is not recommended to completely bend one of the sides. It is better to do this a little on each side.
• As soon as we feel that the panel is giving in, we must begin to act more actively. We pull the panel towards ourselves with our hands.

Advice. The panel is most firmly held in the center, near the panel controls and temperature control. You need to try to pull harder in these places.

• We pull the panel towards ourselves and at the moment of a characteristic click we understand that it has already come out. Everything terrible is behind. We have completed the most difficult task!
• Now it remains to carry out a couple of mechanical actions. We take a curly screwdriver and begin to unscrew the screws on the 4 sides of the radio.

• After unscrewing the screws, we remove the radio tape recorder from the sled.
• Now it's time to do the wires. They are connected to the head unit at the back. This is a wiring harness that ends with a massive plug.

• Now you need to remove the plug and for this we raise the rotary lock of the connector, releasing the plug from engagement with the radio.

Most of the operation is done. The old radio is no longer needed.
Ahead is waiting for the comfort of touch control and DVD playback. You can also throw paper maps out of the glove compartment, because they will no longer be needed - there is a navigator (see), and a high-quality one.
We also advise you to get a rear-view camera so that parking always goes with a bang, even at the tightest intervals.
We continue our process:

• We insert the chip from the car into the head unit connector.
• Next, we connect everything you need to the radio: the central wire, the receiver antenna and GPS.

Note. When connecting the GPS antenna cable, we take into account that the antenna will have to be placed either on a shelf under the rear window or under the dash panel. In any case, there must be free space on top of the antenna. There should be no metal panels or other components that may interfere with communication with the satellite.

• Do not forget to lay the cables for connecting the iPod and the rear view camera if we want to use the capabilities of the standard head unit to its fullest. There is a separate plug and cable set for this.

That's all. We check everything and enjoy the functions.

Review of radio tape recorders Ford Focus 2

In conclusion, I would like to give a description and the capabilities of some models for the Ford Focus. This overview will help to get acquainted superficially with the functions and technical components.

Specifications head unit Ford Focus 2

This:

• HD touchscreen 7 inch panel.
• GPS-module with support for navigation programs Navitel and others.
• Bluetooth built-in, which supports hands-free calling and automatic reception of incoming calls.
• Powerful 45W HiFi amplifier.
• DVD player that reads most modern formats.
• FM/AM radio receiver supporting RDS.
• The ability to control the radio from the buttons mounted on the steering wheel.
• Simultaneous use of the navigator and radio / TV / DVD.
• Support for iPod, USB, various memory cards.
• A unique opportunity to connect a rear view camera or parking sensors.
• Support for PIP function, i.e. picture in picture.
• The ability to control the radio with a remote control.

The presented set of functions is not new today. This will not surprise anyone, but such a set is only for premium cars, which is the Ford Focus.
As for the buttons on the steering wheel, not all Ford models have them. As for the Ford Focus, it has a multi-wheel, with which the device works without problems.

Redpower 12003B and its review

This head unit is a real computer. The “brain” of this head unit is the Windows CE 6.0 operating system, which greatly expands the multimedia capabilities of the entire system.
You can fully enjoy the work of a DVD player that reads various formats or use a GPS navigator that has a Navitel software license agreement. In a word, by installing this semi-computer instead of the factory radio, you can feel like a real astronaut in space, there are so many different functions here.

Specifications

So:

• Processor Arm11 533 MHz.
• Good bright 8-inch display with anti-reflective coating. It has a resolution of 800x480 pixels and can work with 65,000 different colors.
• The presence of a GPS receiver with high sensitivity.
• The presence of Bluetooth (see).
• Built-in microphone and the ability to connect an external microphone.
• Supports A2DP.
• It is possible to listen to music via Bluetooth from a phone, via the Internet, a player, etc.
• The presence of a notebook with support in Russian.
• Possibility to export contacts from a mobile phone in one package.
• Powerful amplifier 4x45 W with a separate output to the woofer (subwoofer).
• The presence of a 3-band equalizer with support for all frequencies and the use of cutoff filters.
• 3D function.
• 4 amplifier line outputs, which a priori helps to create real acoustics with clear sound.

• Radio receiver with FM/AM/VHF support.
• TV receiver analog, supporting Pal/Secam.
• Possibility to connect the parking sensors system.
• Ability to read most modern media and formats.
• Dual zone support.
• Extended on-screen menu with the ability to change the car logo and wallpaper.
• Good navigation with voice prompts for individual settings.

Note. You can set the navigator so that the music from the Audi is not interrupted when audio messages come from the navigator, or you can set it to pause. In addition, in the navigator, you can configure the option of traffic jams.

• The presence of various utilities: a system for diagnosing a HOBD car, a calculator, all kinds of interesting games.

The manufacturer gives a one-year warranty for all models.

Overview of the radio NaviPilot Droid

The most long-awaited novelty. At least, before her release, there was a whole box of conversations.
Expectations were fully justified. There is a regular navigation and multimedia system on the Android platform. The most advanced operating system is Google Android.

This:

• Full integration with the standard interior design of the cabin.
• Ease of installation due to the successful execution of connector technology.
• 7 inch touch screen with HD resolution.
• The processor is high performance.
• GPS with support for almost all known navigation programs, including Navitel, CityGuide and others.
• Ability to work with Google Play.
• DVD drive that plays various formats.
• Radio receiver with memory for 32 stations.
• Support for speech recognition and more.

Do-it-yourself installation of the head units described above can be carried out according to the instructions. The main thing is to use photo and video materials.
Model prices vary. So, the Navitel Pilot Droid radio tape recorder costs about 30 thousand rubles.

Music in the car - sometimes becomes something more than the usual dilution of silence. Fans of quality music and good sound buy expensive multimedia systems just to hear the rich sound of their favorite composition. My article today will be devoted to the issue of installing a radio on the example of a Ford Focus car.

I'll talk about how to install a radio tape recorder with your own hands with a detailed description of the process and photos. So let's go...

Installing the radio Ford Focus

In my case, there is no radio at all, and in its place is a black plug.

1. Remove the plug and wring out the latches. On the reverse side of the plug there are several latches.

2. Having removed it, I had a place for a future radio, as you can see, there is more than enough space.

3. Before that, you should pay attention to the connector for connecting the radio. For convenience and beauty, I recommend using an adapter like: Ford Focus 2 ISO. Here's what it looks like.

4. After installation, this connector must be fixed with a standard clamp.

5. Wiring to the speakers - four twisted pairs, the fifth is a voltage regulator, it goes from the backlight to the radio backlight contact, provided that it is in the radio.

4. Using the connection diagram below, I managed to achieve a bright illumination of the radio during the day and a moderate one that does not "hit the eye" and does not blind - in the dark.

5. Here are the rest of the wires.

Installing the radio, connecting the antenna.

1. In my case, the AUX input wire was already routed into a pocket adjacent to the gear lever, so I had to remove it.

2. Now remove the frame, don't worry, it shouldn't break - the plastic is pretty strong.

3. Unscrew the screws and wring out the special frame clips.

4. In the pictures you can see that on the right and left sides at the bottom there are rectangular vertical holes designed to insert the rest of the frame clamps.

5. After some fiddling, you should have access to the AUX input.

6. In my case, I also had to pull the microphone wire in order for the speakerphone to work.

In my opinion, this information will not interfere with those who are planning to install a subwoofer and are puzzled over where to fix the power switch. It is usually attached with double-sided tape in a separate pocket from the checkpoint, if necessary, it can always be removed.

When done, you need to assemble everything in reverse order.

1. Install the transition frame type: Ford Focus 2 → 1 DIN, the approximate price of such a device is $50-$60.

2. After that, connect the connector Ford Focus 2 to the car radio connector using the previously mentioned adapter.

3. Align the antenna plugs with each other and pay attention to the fact that the yellow-green wire -3 is a plus with the ignition, that is, the radio will only work when the ignition is turned on.

4. I would advise you to connect the wire coming from the radio to the ignition to the wire contact that goes to the battery, and connect everything to the connector output from the battery (orange-black wire is thick - 4).

5. It is best to buy two male-female connectors on the market, then connect them with wires, as shown in the diagram below.

6. When all the connectors are connected, you can install the radio itself directly, be careful not to pinch any wiring.

7. Then fix the radio panel.

That's all, Ford Focus radio installation completed. It remains to put your favorite disc and enjoy the sound and your own work. Good luck to you!

Head unit Ford Focus 2. The second generation has a fairly convenient design features for removal, the audio system is not difficult. To perform this work, you need to perform the following steps: we carry out around the perimeter.

We dismantle the frame and remove the 4 mounting bolts. We pull out the radio tape recorder and disconnect the connectors. And connect a new one to the wires.

Then we remove the radio; (Focus 2) And disconnect the wiring connector.

then insert the connector into the new radio. Nothing needs to be changed, everything falls into place. Don't forget to connect the antenna.

then we insert the radio tape recorder into a regular place.

after that we twist 2 screws. This tape recorder is suitable for the first and second Ford Focus in terms of weight and internal depth dimension.

after that, insert the frame and snap it. The whole process of removing and replacing the head unit with a Ford focus 2 took us about 10 minutes. Then turn on and enter the code on the radio. everything works fine the sound is clear.

Tips: Before buying a radio tape recorder, consult with the seller, a hint on how they do it, some motorists take the usual two master class cards so as not to scratch, and remove the plugs on the central panel. Under the plugs you see 4 bolts unscrew them. here you need to be more careful, as there is a risk that they will fall inside, then you will not find it. Next, unscrew the knobs on the checkpoint and start from the armrest, carefully, remove the console - where the cup holders are. Don't forget to turn off the heated seats. Before removing the leather trim, lift it up and unfasten the plastic reverse gear guides. The console itself is held on by latches, do not be afraid to break them, but at the same time do everything carefully. Remove the 2 bolts at the base of the ashtray. Remove the radio bezel.

Ford Focus 2 cars were equipped with a Sony 6000 CD radio. Before restyling, 4 slots were used for fastening, and after that they began to install a “transition frame”. You can remove it without special tools, but it is easily damaged. Before you remove the radio, on Focus 2 from "generation 1" you must also remove the volume control. And you can make a special tool yourself.

Where to look for slots? The answer is in the video.

Removing the head unit for Ford Focus 2 until 2008

First, 4 fasteners are snapped off: plates are installed in the slot “on the face”. The cutouts of the plates look inward.

Left top notch

Installation order: 2 lower, then 2 upper. Each plate is pressed in until it clicks.

6000 CD, 2007

The radio tape recorder is pulled towards itself by the ears of the plates. And if they are not - for the regulator shaft. To do this, remove the volume knob - pry it with screwdrivers, etc.

Usually, at Focus 2, the radio is removed to install something else. Surprise: the antenna connector is not quite standard.

There are ready-made adapters.

First, the antenna connector is disconnected from the housing, then the main one. Assembly is in reverse order.

Set of tools

The corporate set is called FORCE F-910C1 490.00. The cost is high. But pullers can be made according to the drawing.

Puller, 1 pc.

4 pullers are needed at the same time.

Articles

• 1387728 - radio frame black;
• 1509717 - black frame for climate control;
• EEC GV3301 is equivalent to this: F-910C1 490.00.090417.

Removing the head unit for Ford Focus 2 after 2008

Under the outer frame, 4 strips of a plastic card are installed, as in the photo.

Oval radio

The part is pulled towards itself, it is removed. Then 4 self-tapping screws are unscrewed - this is the radio mount. You may need a T25 key, but for many it’s just a “cross”.

Down with fasteners

The radio tape recorder is pulled out, the antenna cord is disconnected, etc.

The main thing is not to lose the screws when unscrewing.

Articles

• 1539347 - frame for air conditioning (silver);
• 1547160 - the same, under climate control.

aux input

If there is an AUX button on the radio, then there is an input. You need to look at the 12-PIN block with rear speaker wires:

1. RSE L+
2. RSE R+
3. AUX L
4. AUDIO GND
5. RSE L-
6. RSE R-
7. AUX R

We connect to 5-6 and 11-6 contacts. We press AUX, and ... nothing happens.

This option does not work on radios with a CD/DJ button. For everyone else, the FINIS-1310208 connector will do.

Often the wiring is already routed, and then there will be a plug under the glove box trim. Color - pink, soldering not clear.

Video with the dismantling of the oval radio

For a music lover, music in a car is not just a background music or a way to drown out the roar of an engine. In fact, this is a way of life, a way to stand out and just enjoy the sound quality of your favorite melody. Sound fans do not spare money for expensive audio systems, and sometimes even turn their cars into "speakers on wheels".

Today we’ll talk about radio tape recorders, as well as their installation in a car. In this article, I will describe the installation process in detail so that you can install radio in ford focus with your own hands.

Installing the radio Ford Focus - step by step guide

My Ford Focus was completely devoid of any audio device, and after purchasing it, I immediately decided to correct this injustice. As you can see in the photo, I have a black cap instead.

1. First of all, you need to remove this black plug, for this you need to press its latches.

2. After you dismantle it, you have a niche for the radio.

3. Before installing the radio, pay attention to the connection connector. Personally, for convenience and aesthetics, I would advise using a standard adapter when connecting: Ford Focus 2 ISO, in the photo you can see how it looks.

4. When the installation of the radio is completed, fix this connector using the standard clamp.

5. Wires for the speakers - four double wires, the fifth wire is a voltage regulator, it runs from the dashboard backlight to the radio backlight contact. In some "Focuses" it is not.

6. By connecting the radio according to the diagram below, I managed to get good backlight brightness during the day and normal moderate at night.

How to install a Ford Focus radio - antenna connection

1. My AUX input wire has already been routed into a niche.

2. Carefully remove the plastic frame so as not to break.

3. We unscrew the screws, then squeeze the frame latches. On the right and left sides there are rectangular holes that are designed to install the remaining frame clips.

4. You should have access to the AUX input.

Assembly

1. Install the Ford Focus 2 → 1 DIN adapter frame, then connect the Ford Focus 2 connector to the radio connector using the above adapter.

2. The antenna plugs must match with each other, while the yellow-green wire - 3 is "plus" with the ignition. The trick is that the radio only works when the ignition is on.

5. On the radio market, I purchased two male-female connectors, connected them with wires according to the diagram below.

6. After connecting all the wires and connectors, it's time to install the car radio itself and fix its panel.

Now it's time to check the work, Ford Focus radio installation completed, which means you can start listening to your favorite collection. Thank you for your attention, all the best to you.