Excavator wheel single-bucket hydraulic. Manual

02.07.2020

Miscellaneous

Manual

Wheel excavator single-bucket hydraulic

EO-2626.DT, EO-2626.DT.1, EO-2626.DT.2 EO-2621.DT, EO-2621.DT.1

1 Purpose and description of equipment 2

1.1 Purpose of equipment 2

1.2 Equipment description 2

1.3 Specifications 3

2 INTENDED USE 3

2.1 Operating restrictions 3

2.2 General safety measures 3

2.3 Precautions for preparation for use 3

2.4 Safety precautions for the operation of the equipment 3

2.5 Preparing equipment for operation 3

2.6 Using the equipment 3

3 MAINTENANCE 3

3.1 General instructions 3

3.2 Safety measures 3

3.3 Maintenance intervals 3

3.4 Maintenance scope 3

3.5 Applied filter elements, oils and greases. 3

4 POSSIBLE FAULTS 3

5 TRANSPORT 3

6 STORAGE RULES 3

6.1 General provisions 3

6.2 Preparing for short-term storage 3

6.3 Preparing for long-term storage 3

7 ACCEPTANCE CERTIFICATE 3

8 MANUFACTURER WARRANTY 21

2 Purpose and description of equipment

2.1 Purpose of equipment

Backhoe loader EO-2626.DT, EO-2626.DT.1, EO-2626.DT.2(Fig.1, 4) is intended for earthworks in soils of categories I-IV. It is allowed to use an excavator on frozen soils after preliminary loosening of the soil. The front-mounted loading equipment (Fig. 2, 4) is intended for excavation (on soils of categories I-II) and loading and unloading operations of a small volume, transportation of bulk materials over short distances, site planning, filling trenches with bulk soil, raking construction waste.

Backhoe loader EO-2621.DT, EO-2621. DT.1, EO-2621.DT.2 designed for earthworks in soils of I-IV categories. It is allowed to use an excavator on frozen soils after preliminary loosening of the soil. Front Mounted Blade (EO-2621.DT) and a swivel blade ( EO-2621.DT.1) (Fig. 5, 6), designed to perform earthworks (on soils of categories I-II) of small volume, site planning, filling trenches with bulk soil, raking construction waste, etc.

The equipment is designed for operation at temperatures from minus 40 to plus 40°C.

Brief technical characteristics of the backhoe loader are shown in Table 1.

2.2 Equipment description

EO-2626.DT

The loading equipment includes: portal 1, 2, boom 3, transition links 4, 5, boom rods 6, bucket rods 7, lever 8, interchangeable tool 9, boom hydraulic cylinders 10, bucket cylinders 11, high pressure tubes and sleeves 12 ( Fig. 2).

The excavator equipment includes: frame 1, swivel support 2, trunnion hydraulic cylinders 3, outriggers 4, outrigger control hydraulic cylinders 5, boom 6, boom control hydraulic cylinder 7, handle 8, handle control hydraulic cylinder 9, levers 10, traction 11, replaceable tool 12 , a hydraulic cylinder for controlling a replaceable tool 13, a hydraulic tank 14, a battery box 15, a distributor for controlling organs 16, a gear pump 17, high-pressure tubes and hoses 18 (Fig. 3).

EO-2626.DT.1 consists of a Belarus base tractor, excavator equipment - 2, loading equipment - 3 (see Fig. 1).

EO-2626.DT(see fig. 2), except for the interchangeable tool pos. 9, replaced by a universal bucket (jaw) pos. 9 (see fig. 4).

EO-2626.DT(See Fig. 3).

EO-2626.DT.2 consists of a basic Belarus tractor, excavator equipment with a shifting digging axis - 2, loading equipment - 3 (see Fig. 7).

Loading equipment includes all elements EO-2626.DT(see fig. 2)

The excavator equipment includes (see Fig. 8): frame 1, swivel bearing 2, trunnion hydraulic cylinders 3, outriggers 4, outrigger control hydraulic cylinders 5, boom 6, boom control hydraulic cylinder 7, handle 8, handle control hydraulic cylinder 9, levers 10 , rod 11, replaceable tool 12, hydraulic cylinder for controlling replaceable tool 13, hydraulic tank 14 (see Fig. 3), battery box 15 (see Fig. 3), control distributor 16 (see Fig. 9), gear pump 17 , tubes and high pressure hoses 18 (Fig. 8), lanyard 19, bracket 20 (see Fig. 10).

EO-2621.DT And EO-2621.DT.1 consist of a basic Belarus tractor, excavator equipment - 2, grader equipment - 3 (see Fig. 1).

As part of the grader equipment ( EO-2621.DT) includes: spars 1, 2, blade 3, hydraulic cylinder 4, high pressure hose 5 (Fig. 5).

The excavator equipment includes all elements EO-2626.DT(See Fig. 3).

As part of the grader equipment with hydraulic rotation ( EO-2621.DT.1) includes: spars 1, 2, blade 3, lifting hydraulic cylinder 4, turning hydraulic cylinder 5, high pressure hose 6, linkage mechanism 7, frame 8 (Fig. 6).

The excavator equipment includes all elements EO-2626.DT(See Fig. 3).

Figure 1 - EO-2626.DT

Figure 2 - Loading equipment

Figure 3 - Excavator equipment

Figure 4 - EO-2626.DT.1

Figure 5 - EO-2621.DT

Figure 6 - EO-2621.DT.1

Figure 7 - EO-2626.DT.2

Figure 8 - EO-2626.DT.2 excavator equipment

Figure 9 - Distributor "BREVINI"

Picture 10 - Gear pump with multiplier "HYDRAPAC"

2.3 Specifications

Table 1

Name of indicator	Meaning
EO-2626.	EO-2626.	EO-2626.	EO-2621.	EO-2621.

Basic Tractor
Traction class of base tractor
Operating power of the engine, kW.
Maximum transport speed, km/h
Operating speed km/h no more
Ground clearance, mm
Track, mm front wheels rear wheels
Tire pressure MPa (kgf/cm²) front wheels rear wheels	0,18 -0,01 (1,8) 0,15 -0,01 (1,5)
View of the rear attachment	Backhoe
Nominal bucket capacity, m³
Digging depth, mm
Maximum excavator digging radius at parking level, mm
Maximum loading height of the excavator, mm
Rated load capacity of the excavator, kg No axis offset With the maximum offset axis
Maximum cutting force of the excavator, kg
Weight of mounted excavator equipment, kg
Angle of transverse static stability, deg.
Angle of longitudinal static stability, deg.
Gradeability, deg.
View of the front attachment	Bulldozer - loader
Rated loader capacity, kg

Breakout load loader, kg

Hinge height of the maximum raised bucket, mm
Loader blade digging depth, mm
Loader blade width, mm
Loader blade height, mm
The volume of the dragging prism of the loader blade, m³
Blade width, mm
Bucket cutting edge width
Bucket volume, m³
Blade height, mm
Blade drawing prism volume, m³
Blade digging depth, mm
Blade weight, kg
Overall dimensions with attachments, mm
Operating weight, kg

3 INTENDED USE

3.1 Operating restrictions

It is strictly forbidden to operate the equipment with dismantled or faulty components and parts.

The manufacturer is not responsible for the safe operation and operability of the equipment in the event that the consumer changes the design of the equipment, replaces components that do not meet the requirements for them, opens the seals and self-regulates the hydraulic elements.

When operating the equipment, all requirements for maintenance, storage and transportation must be fully complied with.

3.2 General precautions

The operator operating the equipment must carefully study this manual, be trained in the operation of the equipment, obtain an appropriate certificate and undergo a safety briefing in the prescribed manner.

The operator operating the equipment must strictly comply with all safety requirements specified in this manual and in the Belarus Tractor Operation Manual.

Do not inflate tires without pressure control.

Work in the dark or in conditions of insufficient visibility should be carried out only with the working lighting turned on.

It is forbidden to carry out inspection, repair, or other work while under the raised working bodies (boom, or excavator bucket or front linkage). If it is necessary to perform such work, the working bodies must be lowered to the ground or securely fixed in stands. The tractor must be braked and the engine stopped.

It is forbidden to stay in the cabin of unauthorized persons during the operation of the excavator.

When the excavator is running, the presence of strangers closer than 10 m from the tractor is prohibited.

Perform work in the area of overhead power lines only in accordance with the documents "Rules for the protection of electrical networks voltage over 1000V", "Safety regulations for the operation of consumer electrical installations", GOST 12.1.051-90 and other regulatory documents in force in this area.

Carry out work in the protected zone of underground cables, water pipes, gas pipelines, etc., only if there is a permit for these works.

Rated payloads and capacities are based on firm and level ground.

It is forbidden to work on the cliffs and peaks of the soil.

It is forbidden to use the levers or the steering wheel as supports when entering the cab.

It is forbidden to work on the equipment with dents on the hydraulic system pipelines or with damaged high-pressure hoses.

3.3 Precautions in preparation for use

It is necessary to prepare the base tractor for use in accordance with the document "Belarus Tractor Operation Manual".

It is necessary to carefully study all the inscriptions and plates on the equipment.

Checking the level and filling the working fluid in the tank of the tractor's hydraulic system should be carried out only with the hydraulic cylinders of the front mounted equipment fully retracted.

It is necessary to inspect and remove all foreign objects from the equipment.

3.4 Safety measures for the operation of the equipment

Before starting the engine, make sure the gearshift lever is in the neutral position.

It is not allowed to leave the excavator with the engine running without supervision.

During breaks in work, measures must be taken to prevent tipping due to ground deformation or landslides.

Loading cargo or unloading soil into the vehicle must be done from the side or rear. Carrying the bucket over the vehicle cab is prohibited.

Engage the equipment control levers only while sitting on the seat of the base tractor.

The tractor PTO must be switched off during transport crossings.

During transport crossings, the front and rear attachments must be set to the transport position and secured.

Raise the outriggers to the transport position only after lifting the boom to the transport position and turning the handle towards the boom.

Work on soils with a slope close to the maximum allowable (about 5 °) should be carried out at medium overhangs of loading and excavating equipment.

Work with excavator equipment on soft soils should be carried out using additional platforms under the outrigger supports and under the bucket (dump) of the front attachment.

To prevent the tractor from tipping over prohibited:

Carry out loading and unloading operations on sites with a slope of more than 5 °;

· when working with the loader boom raised to the maximum, perform sharp braking, make sharp turns or abrupt engagement of the clutch;

drive at a speed of more than 5 km/h on roads with a side slope, large bumps or sharp turns

· lift a load of more than 500 kg with an excavator bucket and more than 900 kg with a loader bucket;

· excavate soil from under the outriggers.

If the engine stops, to lower the work equipment, you must:

Move the control lever of the front attachment to the position " FLOATING»;

Move the excavator equipment control lever to the position "LOWING".

The development of pits and trenches with vertical walls in soils of natural moisture (in the absence of groundwater) should be carried out to a depth of not more than:

1m in sandy soils;

· 1.25m in sandy loam;

1.5m in clays and loams;

· 2m in especially dense soils.

The development of pits and trenches to depths greater than those indicated should be carried out with slopes.

3.5 Preparing equipment for operation

3.5.1 Commissioning the equipment

When sending the equipment from the manufacturer, some parts and assembly units of the equipment and the base tractor are dismantled for ease of transportation. These parts and assembly units must be installed in place. The list of parts and assembly units is given in the packing list.

It is also necessary to make an external inspection of all threaded connections of the equipment, tighten if necessary.

3.5.2 Preparing the basic tractor for work

Preparation of the base tractor for work is carried out in accordance with the document "Belarus Tractor Operation Manual".

Before starting operation, the distance from the end of the axle shaft to butt install the hubs of the left rear wheel in the same way as the right wheel, i.e. colasa must be installed symmetrically.

3.5.3 Preparation of excavator equipment for work

Lubricate the excavator according to the lubrication chart. Check the level of working fluid in the excavator hydraulic system tank.

3.5.4 Preparing the front attachment for work

Carry out an external inspection and eliminate the detected malfunctions.

Lubricate attachments according to the lubrication chart. Check the level of working fluid in the tank of the tractor's hydraulic system. Check the level of the working fluid with the hydraulic cylinders fully retracted.

3.5.5 Equipment run-in

The running-in of the base tractor is carried out in accordance with the document “Belarus Tractor Operation Manual” (section “Tractor Running-in”).

After running in the base tractor, it is necessary to perform maintenance after the running in (after 30 hours) in accordance with the document "Belarus tractor operation manual" (section "Tractor running in").

The running-in of the excavator is carried out in two stages:

movement of all hydraulic cylinders for 30 minutes at idle engine speed;

· operation of the excavator at medium load (filling the bucket no more than 50%) for 30 hours (5 shifts) at medium engine speeds.

movement of all hydraulic cylinders for 20 minutes at idle engine speed;

· operation of a bulldozer-loader at an average load (filling the bucket no more than 50%) for 30 hours (5 shifts) at medium engine speeds.

Break-in of the blade is not performed.

Running-in of the swivel blade is not performed.

After running in, it is necessary to inspect the equipment externally and eliminate the detected problems.

After running in, it is necessary to make the first replacement of the filter element of the hydraulic system of the excavator.

3.6 Use of equipment

Engine starting:

An ETO must be performed before starting the engine.

Prepare and start the engine in accordance with the document "Belarus Tractor Operation Manual".

3.6.1 Using the excavator:

When operating the excavator, it is necessary to strictly comply with all the requirements of the safety measures specified in this manual.

Before starting work, it is necessary to make sure that there is a working fluid in the hydraulic tank of the excavator and the multiplier of the hydraulic pump PD-3/36E18. Switch on the tractor PTO drive at 1000 rpm if the machine is equipped with an NSh-71L hydraulic pump, and at 540 rpm if the machine is equipped with a PD-3/36E18 hydraulic pump. (Switching the PTO, see the operation manual Belarus).

When operating in the spring-summer period, use MGE-46V oil. When operating in the autumn-winter period, use VMGZ oil.

When the pointer of the vacuum gauge of the filter of the hydraulic system of the excavator is in the red zone, it is necessary to replace the filter element.

Before moving the excavator boom or arm, it is necessary to lower the excavator outriggers and the bucket or blade of the front attachment to the ground, remove the column locking pin in the transport position, and unlock the boom locking mechanism in the transport position.

Check the operation of the excavator at idle engine speed by moving the cylinders.

When the excavator is operating, the bucket must be installed so that there is no friction of the back wall against the ground, and at the same time, it is necessary to ensure a minimum digging angle.

To reduce cycle time and increase productivity, it is necessary to combine the working movements of the hydraulic cylinders. It is recommended to avoid moving the hydraulic cylinder rods to full stroke, as this will lead to frequent activation of the safety valve.

It is not allowed to combine the process of digging and turning the column.

After completing the work, it is necessary to install the excavator equipment in the transport position and turn off the PTO drive.

When working on clays and loams, it is necessary to clean the bucket, avoiding its heavy contamination.

To transfer the excavator equipment EO-2626.DT, EO-2626.DT.1, EO-2621.DT, EO-2621.DT.1 to the transport position, it is necessary:

To transfer the excavator equipment EO-2626.DT.2 to the transport position, it is necessary:

move the carriage to the left (in the direction of travel);

fold the boom and handle and turn the column so that the bucket is on the right (in the direction of travel);

fold the bucket under the handle (pull out the bucket hydraulic cylinder rod);

fix the column in the transport position with a finger;

fix the boom in the transport position with a lock;

Raise the front attachment to the transport position;

Raise outriggers to transport position.

3.6.2 Using the loader

When operating the loader, it is necessary to strictly comply with all the requirements of the safety measures specified in this operation manual.

Before starting operation, it is necessary to check the operation of the loader at idle engine speed, performing cylinder movements.

When working with a loader, the excavator equipment must be in the transport position.

When using a loader with a bucket, place the bucket horizontally on the ground and fill the bucket while driving the tractor forward. After filling the bucket, it is necessary to turn the bucket up and raise the boom to a height that ensures the passage of the bucket above the vehicle body, taking into account the turn during unloading, drive up and unload the bucket.

To reduce cycle time and increase productivity, it is necessary to combine the working movements of the tractor and the bulldozer-loader:

moving the tractor forward and turning the bucket up;

Tractor moving back and boom lifting.

When using a loader with a bucket for loading and unloading operations, the inclusion of a forced drive of the front axle of the tractor is prohibited.

When using a loader with a blade, it is necessary to set the optimal cutting angle, and when the tractor moves forward, implement the blade into the soil, increase the soil volume and move it with continuous cutting of the soil.

3.6.3 Blade use

When working with the blade, the excavator equipment must be in the transport position.

When using the blade, it is necessary to lower the blade, and when the tractor moves forward, implement the blade into the ground, increase the volume of the soil and move it with continuous undercutting of the soil.

4 MAINTENANCE

4.1 General instructions

Carrying out maintenance is aimed at ensuring reliable and durable operation of the equipment.

Before all types of maintenance, except for daily maintenance, the equipment must be cleaned of contamination.

Before performing the lubrication operation, the lubricators, as well as the surfaces located next to the lubricated element, must be cleaned.

A clean, level area of approximately 30 m² must be prepared for maintenance.

Collection and disposal of waste fluid is carried out in accordance with GOST 21046.

Refueling of the excavator with working fluid must be carried out in a closed way and ensuring the filtration fineness is not more than 10 microns.

4.2 Security measures

When carrying out maintenance, the tractor must be set to the handbrake, shoes are placed under the wheels, the engine is turned off.

It is forbidden to carry out inspection, repair and other work with raised working bodies (boom, or excavator bucket or front linkage). If it is necessary to perform such work, the working bodies must be lowered to the ground or installed on stands.

All movements by the working body, including when checking the settings of the safety valves, should be carried out only from the tractor cab.

When dismantling the hydraulic systems of the equipment (for example, to install a pressure gauge), you must make sure that there is no pressure in the hydraulic system, for which you need to turn off the PTO or tractor hydraulic pump, lower all working bodies to the ground and move all control levers.

4.3 Maintenance intervals

For the convenience of carrying out maintenance of the equipment, it is combined with the maintenance of the base tractor.

Maintenance intervals are shown in table 3.

Table 3

Type of maintenance	Periodicity

Every Shift Maintenance (ETO)	at the beginning of the shift (after 10 hours)
Maintenance No. 1 (TO No. 1)	after 125 hours
Maintenance No. 2 (TO No. 2)	after 500 hours
Maintenance No. 3 (TO No. 3)	after 1000 hours
Seasonal maintenance (SRT)	when switching to spring-summer or autumn-winter operation

4.4 Scope of maintenance

Table 4

	Technical requirements	Devices, tools, fixtures and materials
Every Shift Maintenance (ETO)

1. Perform an external inspection. Eliminate detected faults.
2. Check the level of working fluid in the tank of the hydraulic system of the excavator.
3. Visually check the leakage of the working fluid	Leakage of the working fluid is not allowed	A set of keys
4. Check the fluid level in the PD-3/36E18 pump multiplier.	The level should be visible in the oil gauge window.
Maintenance No. 1 (TO No. 1)
1. Clean equipment and tractor.
2. Perform ETO operations		A set of keys
2. Perform maintenance operations No. 1 of the tractor.
4. Carry out lubrication work	Apply lubricant until it comes out of the gaps	Grease blower
5. Check the oil level in the hydraulic pump drive gearbox	The oil level must be at least 5 mm from the lower edge of the control hole
6. Perform an external inspection of the threads. compounds	Loose connections must be tightened.	A set of keys
Maintenance No. 2 (TO No. 2)

1. Perform maintenance operations No. 1.		A set of keys
2. Perform maintenance operations No. 2 of the tractor.	According to the "BELARUS Tractor Operation Manual".	Grease blower
3. Tighten all threaded connections (fastening the pump drive, distributor, tank, control panel, etc.)	Threaded connections must be tightened	A set of keys
4. Perform an external inspection of the high pressure hoses	Contact of sleeves with each other except for the places of their fastening is not allowed.
Maintenance No. 3 (TO No. 3)
1. Perform maintenance operations No. 2,		Grease blower
2. Perform maintenance operations No. 3 of the tractor.	According to the "BELARUS Tractor Operation Manual".	Grease blower
3. Check and, if necessary, surfacing knives and bucket walls	Wear of the overlay to the base metal is not allowed.	Surfacing electrode P-590V
4. Perform an external inspection of the equipment, if necessary, make repairs.	Cracks and deformations of the metal are not allowed	Forging and welding equipment
5. Perform an external inspection of the rods and wipers of the cylinders.	Cracks squeezing out the wipers are not allowed. Leakage of oil on the rod under load (during operation) more than 6 drops per minute is not allowed
6. Set the boom at a 45˚ angle and the arm at a 90˚ angle to the boom	Movement of rods less than 20 mm for 5 min. not allowed	Replace cylinder or repair in workshop
7. Fill the loader bucket with a load of 400-500 kg and raise the boom to the maximum reach.	Movement of rods less than 20 mm for 3 min. not allowed	Replace cylinder or repair in workshop
8. Replace the filter element, the working fluid of the excavator hydraulic system.

	Before replacing the filter, thoroughly clean and rinse the surface of the tank located next to the tank.
9. Change the oil in the hydraulic pump drive multiplier PD-3/36E18.	Oil Tap-15V. To the level of the control hole.
10. Paint areas with damaged coating		E-115 enamel
Seasonal maintenance (SRT)
1. Perform the next maintenance operations.		Key set, grease gun
2. Carry out operations corresponding to the seasonal maintenance of the tractor.	According to the "BELARUS Tractor Operation Manual".
3. Change the working fluid of the hydraulic system of the excavator	When operating in the autumn-winter period, use VMGZ oil. When operating in the spring-summer period, use MGE-46V oil. Replace the working fluid immediately after completion of work. Drain to produce from the tank.

3.5. Used filter elements, oils and greases.

The oils and greases used are listed in Table 5

Table 5

Place of application	Designation	Qty	Substitute
Excavator hydraulic system	When operating in the autumn-winter period, use VMGZ oil.
	When operating in the spring-summer period, use MGE-46V oil.
Tractor hydraulic system	When operating in the autumn-winter period, use M8G2 oil.		L-HL 15 HYDROL Energol HLP-HM 22 BP Hydraulikoil HLP 22 L-HL 46 HYDROL Energol HLP-HM 46 BP Hydraulikoil HLP46
When operating in the spring-summer period, use M10G2 oil.
Grease lubrication points
filter element	Filter element "Filtrotec"

5 POSSIBLE FAULTS

Table 6

The name of the failure and its external manifestations	Probable Cause	Remedy
Oil leaking at joints	Loose tightening or dirt on mating surfaces.	Tighten the connections, clean the connections from dirt, wrap fumlent or tow, clamp the connections.
Movement of equipment caused by spontaneous movement of cylinders.	Worn piston cylinder seals.
Faulty hydraulic distributor.	Replace the valve or have it repaired in a workshop.
Leakage of oil on the rods of hydraulic cylinders	Wear of cylinder piston seals.	Replace the cylinder or have it repaired in a workshop.
Mechanical damage to cylinder rods	Replace the cylinder or have it repaired in a workshop.
Uneven (jerky) or slow movement of equipment	Presence of air in the hydraulic system	Remove air from the hydraulic system
Faulty hydraulic pump	Replace hydraulic pump
Knocks, squeaks, play in swivel joints.	Worn bushings or pins.	Replace bushings or pins.

6 TRANSPORTATION

5.1. Transfer to the place of work

Moving to the place of work on your own is recommended only for short distances.

When moving, the equipment must be transferred to the transport position.

Fixation of the rotary support, carriage and boom in the transport position should be carried out at any crossings outside the working site.

It is forbidden to drive at a speed of more than 5 km / h on roads with a side slope of large bumps or sharp turns.

The equipment is transported by any means of transport.

During transportation by rail, you must:

· The floor of the platform and all fasteners must be free of dirt, snow or ice. In winter, sprinkle the floor of the platform and supporting surfaces with a layer (1-2 mm) of sand.

· Place all parts removed from the equipment and tractor for the period of transportation, together with operational and shipping documentation, into the tractor cab.

· Place the cab and ignition keys in the tractor's tool box.

· The bars and pads used to restrict movement must be nailed to the floor of the platform with 2 nails with a diameter of at least 4mm, and the bars installed in front of the front and rear wheels must be nailed to the floor of the platform with 6 nails.

· Each backhoe loader must be secured against longitudinal and transverse movement with 4 stretch marks made of soft (thermally annealed) wire according to GOST 3282 with a diameter of 4 mm in three threads. Arrange the braces in such a way that the angle between the bracing and its projection onto the platform floor, as well as the angle between the projection of the bracing onto the platform floor and the longitudinal axis of the platform does not exceed 45°.

· Fasten the front extensions to the wheel disks at one end, and the side rack-mount brackets of the platform with the other.

· Fasten the rear extensions with one end of the nuts to the cargo hubs of the rear wheels, and the other end of the side rack-mount brackets of the platform. Set the tractor gear lever to 1st gear and apply the parking brake and tie it with a soft wire behind the lower cross member of the seat.

· When performing loading and unloading operations, it is necessary to comply with safety requirements in accordance with GOST 12.3.009-76.

During transportation by road it is necessary:

· Place the equipment correctly and securely fasten it so as not to create dangerous situations on the roads and not to restrict the driver's view.

· If the extreme points of the submerged equipment units are located at a distance of more than 0.4 m from the outer edge of the front or rear clearance of the vehicle, the dimensions must be indicated by shields or flags during the day, and at night and in other conditions of insufficient visibility - with reflective devices and lanterns: white in front and red in the back.

· All loading and unloading operations should be carried out only with the help of lifting and transport vehicles with a carrying capacity of at least 0.5 tons, deformation of structural elements is not allowed.

7 STORAGE RULES

7.1 General

Storage of the base tractor must be carried out in accordance with the Belarus Tractor Operation Manual, section Tractor Storage Rules.

Equipment can be subjected to short-term storage (from 10 days to 2 months) or long-term storage (more than 2 months). The equipment must be stored indoors or under a canopy. The maximum period of storage of equipment indoors is 1 year, under a canopy - 9 months.

During storage, once a month, it is necessary to check the condition of the equipment and eliminate any discrepancies found.

7.2 Preparing for short-term storage

To prepare equipment for short-term storage, perform the following steps:

preparation of the tractor for short-term storage;

· maintenance No. 1;

clean and paint damaged painted surfaces;

· cover unpainted surfaces and protruding rods of hydraulic cylinders with grease;

Wrap the rods of the hydraulic cylinders with waxed or oiled paper and tie them with twine;

· Install excavator and loader buckets on wooden platforms.

7.3 Preparing for long-term storage

To prepare equipment for long-term storage, perform the following operations:

preparation of the tractor for long-term storage;

maintenance No. 2;

Operations of equipment preparation for short-term storage;

Replace the working fluid in the hydraulic system of the excavator. After replacement, it is necessary to perform 2-3 full strokes with each hydraulic cylinder;

For long-term storage, the base tractor must be installed on stands, which must be placed at the places where the jacks are installed and the tire pressure must be reduced to 70% of the nominal value.

The high pressure hoses and pipelines are disconnected, the oil is drained, the fitting holes are closed with special threaded plugs. With the closed storage method, it is allowed to leave the sleeves and pipelines on the machine.

To protect unpainted surfaces of parts, it is recommended to use PVK GOST lubricants.

Reopening

During depreservation it is necessary to perform the following operations:

re-preservation of the tractor;

Fill with grease all connections according to the lubrication chart;

Perform maintenance No. 2;

· if necessary, depending on the season, replace the working fluid in the hydraulic system of the excavator.

8 ACCEPTANCE CERTIFICATE

Universal wheeled single-bucket hydraulic excavator _____________________________ for excavation, loading, light leveling work on the basis of the Belarus tractor.

Serial number ________________________ Chassis number ____________________________________

Conforms to specifications and is recognized fit for operation.

M. p. Date of manufacture

Signature of the person responsible for acceptance _____________________________________

8 MANUFACTURER WARRANTY

The manufacturer guarantees the compliance of the equipment with the requirements of the technical documentation, provided that the consumer observes the rules of operation and storage.

Warranty period of operation is 12 months. The beginning of the warranty period is calculated from the date of commissioning, but no later than 6 months from the date of sale.

Claims are made in accordance with the current legislation of the Republic of Belarus

(manufacturer, address)

__________________________________________________________________________________

PHOTO Front wheel excavator-loader based on tractor MTZ EO-2101-21

Factory manufacturer:
-Donetsk Machine-Building Plant LLC (Donetsk Machine-Building Plant)
346330, Russia, Donetsk, Rostov region, st. Lenin Ave., 37 A

Specifications:front wheel excavator-loader based on tractor MTZ EO-2101-21

Weight, kg	6900
Excavator bucket capacity, cubic meters	0,28
Loader bucket capacity, cubic meters	0,8
Engine power, kW	60
Overall dimensions, mm	7500/ 2500/ 3800
Max. backhoe dig depth	4,3
Backhoe unloading height, m	3,6
Backhoe digging radius, m	5,5
Cutting force on the edge of the bucket, kg	3910
Loader unloading height, m	2,7
Loader bucket capacity, kg	700
Loader bucket width, mm	2000
Backhoe Loader Base Chassis	Wheel tractor MTZ-82.1 or MTZ-82P
Engine model	D-243
Wheel formula of the base MTZ tractor	4 x 4
Turning radius, deg	176
Maximum travel speed, km/h	19
Pressure in the hydraulic system, MPa	16
Additional attachments	Narrow excavator bucket, - hydrohammer GPM-120, Delta fine-5, - EU welding machine, - clamshell bucket 0.32 cubic meters, - ripper tooth. - welding installation EU-10, - forklift device
Design features	Displacement of the digging axis of excavation equipment. Bucket Loader
Sale of EO-2101-21	You can buy a front wheel excavator-loader based on the MTZ tractor from the company - Donetsk Machine-Building Plant LLC, which is engaged in their production and sale.

Special equipment catalog services:
The catalog provides an opportunity to get acquainted with the technical characteristics of each model of special equipment and the manufacturing plant. At the same time, you can make a choice and buy or sell, rent the selected model of equipment, find out the latest news from the manufacturing plant.

Backhoe loader EO-2101-20 designed for excavation and loading and unloading operations, associated with frequent movements between work objects. Excavators of the presented model are widely used for maintenance and repair of communication networks, heat, water, gas, electrical drainage works, and are also used in landscaping and landscaping of urban areas by public utilities. Backhoe loaders EO-2101-20 are one of the most common earth-moving machines that are used to solve many problems in various industries. Backhoe loaders EO-2101-20 are also needed not only for ground work, but also for loading / unloading. Frontal jaw loader - replaceable equipment of the excavator, designed for mechanization of unloading operations.

The main working element of the excavator of the presented model is the bucket, with the help of which most of the processes are carried out, and thanks to which the machine becomes universal. Any construction project is indispensable without help EO-2101-20, as it is a universal type of equipment capable of performing a variety of functions. Thanks to the main working element - the bucket, the wheeled excavator-loader EO-2101-20 widely used in earthworks in quarries, for digging all kinds of channels, trenches and pits in soft soils. Due to the reduced bucket volume, the excavators of the presented model are very maneuverable and their main advantage lies in the fact that they can be used in urban areas.

A hydraulic hammer or other attachments will easily turn EO-2101-20 into a multifunctional machine. The hydraulic grab serves as an additional equipment for the excavator for loading operations with bulk materials. A hydraulic hammer, used instead of a bucket, helps to lift hard ground and do other similar work. The use of attachments allows you to significantly expand the scope and functionality, so it's worth buying EO-2101-20 with additional equipment, which will allow the equipment to pay off in the shortest possible time.

EO-2101-20 are made with a displaceable digging axis. The shifting axle excavator mechanism and jaw bucket are the main equipment of this excavator. The excavator of the presented model combines the functions of a planner and a loader. The dimensions of the backhoe loader are quite small due to the shifting axle, which makes it an excellent opportunity to carry out any construction work in the vicinity of houses under construction and other objects.

Hydraulic control of the working elements makes it possible to perform up to 4 operations simultaneously, which significantly increases the performance of the model as a whole. The high level of productivity and quality combined with an acceptable price make EO-2101-20 competitive. A hydraulic system using imported (Italy) components (hydraulic distributor, filtration elements, hydraulic cylinders), a modernized comfortable cabin that meets the requirements of the OECD, with excellent ventilation and heating systems, which is the reason to buy EO-2101-20.

Basic Tractor Backhoe Loader EO-2101-20 produced by the Minsk Tractor Plant, which was founded on May 29, 1946 and over the years of its existence has become one of the largest manufacturers of agricultural machinery in the world. To date, MTZ software offers consumers more than fifty models of different machines in more than a hundred assembly options for all climatic and operating conditions. The correctness of the decision to buy EO-2101-20 is convinced by the fact that all the equipment sold by the plant received international certificates confirming its compliance with EU standards. Distinctive feature of the model technique EO-2101-20 is versatility, reliability, cost-effectiveness and a high level of productivity.

Backhoe loader EO-2101-20 It is equipped with a modern comfortable cabin of increased volume with a panoramic glass that increases visibility, which facilitates work and increases the degree of accuracy and safety in operation. The control of the working bodies of the excavator is hydraulic, joystick, with the possibility of simultaneously performing 4 operations. Backhoe Loader Hydraulic System EO-2101-20 manufactured using imported components: hydraulic distributor, filtration elements, hydraulic cylinders. The hydraulic system allows you to perform work as accurately and smoothly as possible.

Sale EO-2101-20 carried out in our company. The sale of EO-2101-20 is carried out to all regions of Russia with delivery in the shortest possible time, which is one of the reasons why it is worth buying EO-2101-20 in our company. Moreover, our company guarantees an individual approach to each client, which allows you to buy EO-2101-20 at an acceptable price.

If you decide to buy EO-2101-20, then contact us by the phone numbers listed on our website in the "Contacts" section, or by e-mail, the address of which is located in the same section. The company's managers will acquaint you in more detail with the technical and operational characteristics of this and other models of excavators, as well as provide the necessary information on the procedure for purchasing equipment.

The EO-2101 excavator was created on the basis of the tractors of the Minsk Tractor Plant ("Belarus-92P", "Belarus-826", "Belarus-892", "Belarus-82.1"). The model itself was also produced in several trim levels: with domestic and imported hydraulics, with an offset digging axis and with jaw loading equipment. Optionally, the equipment was equipped with a grader bucket, a ripper tooth, a narrowed backhoe bucket, a welding machine and a hydraulic hammer.

EO-2101 is used to perform loading and unloading and earthworks associated with regular movements within the site and between objects. Also, this excavator is used for the repair and maintenance of communication networks, in gas, heat, water and electric drainage works, in landscaping and landscaping of urban facilities. Model EO-2101 is one of the most common earthmoving machines in Russia and the former CIS countries. Due to the presence of a front jaw loader, EO-2101 is also used for mechanization of unloading operations.

The main working element of the technique is the bucket, through which the main part of the work processes is carried out. This element makes the excavator more versatile. It is the bucket that allows the use of EO-2101 in earthworks (digging pits and trenches, digging channels and quarries).

A slightly reduced volume of the equipment bucket added to its maneuverability. This made it possible to use the excavator in urban environments.

Attachment

A wide range of attachments turns the EO-2101 into a multifunctional machine. So, the hydraulic grab is used for loading and unloading operations with bulk materials, the hydraulic hammer, installed instead of the bucket, allows you to lift hard soils.

EO-2101 is available in several modifications. In addition to the classic version, these are variations of EO-2101-10, EO-2101-11, EO-2101-12, EO-2101-13, as well as EO-2101-20, EO-2101-21, EO-2101-22, EO-2101-23. Between themselves, these modifications differ in configuration and the presence of various additional equipment. However, all versions have the following advantages:

long period of use without additional investments;
high level of performance;
high permeability;
the presence of a spacious and comfortable driver's cab, providing excellent protection against moisture and dust. This element is made in accordance with safety standards;
structural reliability;
ease of maintenance and management;
wheel formula four by four;
sustainability.

Photo

Specifications

Overall dimensions of EO-2101:

length in transport position - 7630 mm;
width - 2500 mm;
height - 3800 mm.

The weight of the excavator is 6500 kg. At the same time, the equipment is capable of accelerating up to 18 km / h.

Operational characteristics of equipment:

load capacity - 750 kg;
unloading height - 2700 mm;
digging depth - 4300 mm;
bucket capacity - 0.28 (0.8) cubic meters;
loading height - 3600 mm
bulldozer blade width - 2100 mm.

Fuel consumption

The fuel tank capacity of EO-2101 is 127 liters with a specific fuel consumption of 159.5 g/kWh.

Engine

EO-2101 is equipped with a 4-stroke 4-cylinder piston diesel engine "D-243" with in-line vertical arrangement of cylinders, compression ignition and direct fuel injection. This unit is not turbocharged. The EO-2101 power plant is distinguished by high torque, which makes the equipment more manageable and dynamic. The high compression ratio, characteristic of the D-243 unit, ensures maximum combustion of the working mixture, increasing efficiency and economy.

The power plant of the excavator is designed to work in temperature conditions from -40 to +40 degrees.

Characteristics of the motor "D-243":

working volume - 4.75 l;
power - 60 (81) kW (hp);
rotational speed - 1600 rpm;
cylinder diameter - 110 mm.

Device

EO-2101 is produced with a displaceable digging axis. As standard, the excavator is also equipped with a jaw bucket, which allows it to combine the functions of a loader and a planner. Due to its compact dimensions, the equipment is used to perform construction work near houses and facilities under construction.

Hydraulic control allows the driver to simultaneously perform up to four different operations, which significantly increases the productivity of the model. It is the high level of quality, high performance, coupled with an affordable price that make EO-2101 so popular.

The latest hydraulic system, which includes Italian components (hydraulic cylinders, hydraulic distributor and filtration elements) and a redesigned cab that meets the requirements of the OECD, allows the equipment to successfully compete with its analogues.
The base chassis, on the basis of which the EO-2101 is made, is manufactured by the Minsk Tractor Plant. At the same time, the excavator has international certificates of compliance with EU standards. Distinctive features of the technique are efficiency, versatility and reliability.

Separately, we should dwell on the EO-2101 cabin. It has an increased volume and panoramic glass with a great view. This improves safety and precision in various operations and makes work easier. Management of working bodies joystick.

Price of new and used

It is rather problematic to find a new EO-2101 excavator, since the production of this model has been completed. The supply of used options is also very limited. Modifications of 2007 in working condition are estimated at 450,000-650,000 rubles. The cost of the 2008-2010 versions will be 800,000-900,000 rubles.

Analogues

Analogues of the EO-2101 model are the EO-3323 and JCB 3CX Boreks-3106 excavators, which have similar technical parameters.