How to change engine oil toyota corolla. Toyota corolla engine oil change

Careless operation, untimely service or the use of poor quality oil, it is quite possible that the Toyota Corolla oil filter will no longer cope with its duties within a few months after its installation.

According to the recommendations of professionals, replacing the oil filter and engine lubricant on a Toyota Corolla is recommended every 10 thousand kilometers. Some people prefer to entrust all service work to service station specialists, but many motorists do an excellent job with such procedures on their own.

Before replacing, you must purchase a good oil filter. It is not worth saving here, it is better to make a purchase in a specialized store and take the best one, even if you have to overpay a little. Moreover, the difference will not be too big.

[ Hide ]

Where is?

Replacing the oil filter on a Toyota Corolla is a simple process, as the filter is located in an accessible place - under the bottom of the car. And to replace it, you do not need to remove additional systems.

Step by step replacement instructions

How is the process of replacing the filter on Toyota Corolla models released after 2010? The replacement of the oil filter element on models of an earlier year of manufacture follows almost the same scheme, except that a traditional oil filter is used, made in a metal housing, instead of a filter insert.

It is better to carry out all work on a lift or overpass, but if this is not possible, then the usual viewing hole, which is in virtually any garage, will do. If motor protection is provided, then it must be removed. In this case, the bolts do not have to be completely unscrewed, but it is enough to pull them forward a little.

What will be needed?

• Screwdriver Set;
• special key to remove the barrier;
• funnel;
• a set of keys;
• new lubricant;
• rags;
• waste drain container.

Stages

1. Use a screwdriver to remove the rubber plugs in the motor. Under the drain hole, we first put a container for draining the waste liquid.
2. Using the wrench, unscrew the plug to drain the oil.
3. We merge processing.
4. We twist the cork.
5. Pull out the protective plate.
6. We unscrew the cap with the old filter using a special key. This must be done carefully.
7. We take it off.
8. Replace, after lubricating with oil, the sealing ring.
9. Pour a little oil into the new filter, a little more than half.
10. Install it in place of the old one.
11. Install the locking protective plate to the position it was in before.
12. Fill in new oil.
13. We start the engine and let it run a little.
14. We check the level.
15. In case of shortage, top up and vice versa.

Many experts advise flushing the car engine when changing. But this procedure is optional if you use high-quality consumables and carry out all service work on time.

Video "Installing a new oil barrier"

This video shows in detail the process of changing the oil filter on a Toyota Corolla car.

Every motorist knows that timely oil changes are necessary for the smooth operation of the engine. In the Toyota Korolla engine, it should be carried out every 5-10 thousand kilometers. You can replace it in a car service or on your own. An oil filter is sold at almost any major auto shop. It is better not to save money and buy a quality product from a well-known manufacturer. The same goes for the oil itself. Using poor quality grease can cause the filter to become clogged and fail.

1. A container into which the used lubricant will merge. It is desirable that it includes at least 4 liters and that it is not very wide. Otherwise, splashes will fall on the floor.
2. Rubber gloves to protect your skin from burns.
3. Torque head. With it, you can loosen the drain plug.
4. Band key. This tool will be needed to unscrew the filter, which must be changed at every oil change. Instead of a strap wrench, a socket wrench may also work.
5. A rag or newspaper with which you can remove splashes from the floor.

How is the process of changing the oil in a Toyota Corolla car?

Folk way to check the condition of the oil:

• Warm up the Toyota Corolla power unit to an operating temperature of 40 - 45 ℃;
• take a few drops of oil from the filler cap, drip onto a white paper towel;
• wait 10 minutes, look at the oily circles.

The inner and outer circles are light in color, without clear outlines - motor fluid can still last. When two circles with a clear rim and a dark color - the oil is subject to a quick update.

Changing the oil in a Corolla engine with your own hands is not a difficult process, every car owner can do it. Experience and no special equipment required.

How often do you change the oil in a Toyota Corolla engine?

• quality of cooling of engine components;
• thermal conductivity;
• reduction of wear of components, constituent elements;
• stability of the power unit;
• reduced fuel consumption;
• reduction in the amount of toxic emissions, the formation of carbon deposits in the combustion chamber, cylinder.

Waste engine oil harms rubbing parts, components, and contributes to their premature wear.

Factors affecting oil change intervals:

• general technical condition of the Toyota Corolla;
• frequency of operation;
• geographical conditions;
• climatic temperatures;
• downtime, congestion in traffic jams;
• quality of fuel, engine oil.

Oil selection and required volume

The manufacturer of Toyota Corolla 150 recommends filling in the original Toyota engine oil with a viscosity index of 0W-20, 5W-30. The volume of oil in different engines is 4.00 - 4.25 liters. For exact data, please refer to the instruction manual. For models 2011, 2013, 2014, the volume is 4.05 liters.

Many car owners are interested in the question: what kind of liquid to fill in to extend the life of the technical tool. If the owner does not have sufficient funds to purchase factory oil, choose an alternative option. The class must be at least semi-synthetic, better "synthetics". The mineral base is not recommended for use, since the technical characteristics of the fluid do not match the Toyota Corolla engine standards.

It is obvious that improperly selected oil cannot fully lubricate and cool the rubbing parts of the power unit. Among the brands tested are the following: Mobil, Shell, Castrol. By replacing the oil in the Toyota Corolla engine yourself, you will extend the life of the engine, reduce the coefficient of friction, and fuel consumption.

Toyota Corolla engine oil change - instructions

The process of self-changing the oil in a Toyota Corolla engine will take no more than 20 minutes, subject to a professional approach, the availability of consumables and components.

Together with the oil change in Toyota Corolla, we will update the filter element with our own hands, check the level of transmission fluid in the gearbox.

Sequencing:

• Toyota Corolla E150 (1.6) is installed on the inspection channel, the power unit is heated to a working temperature of 40 C;
• With the key to "14" we unscrew the drain plug of the oil pan. We merge mining into an empty container;
• We wait 7 - 10 minutes until the oil drains as completely as possible, screw the cork;
• To the left of the hole is a container for the cleaning element. We unscrew it with a special ring wrench, replace it with a new one;
• In the engine compartment, through the filler neck, we fill in new semi-synthetics (synthetics) in a volume of 4.0 - 4.250 liters.

We start the power unit for 2 - 3 minutes, turn it off, make a control measurement of the oil on the dipstick, the level should not exceed the MIN and MAX marks.

Subject to the recommendations, the purchase of original consumables, the subsequent replacement after 10 - 15 thousand km. The algorithm is not complicated, it is quite possible to change the motor fluid in a garage yourself. In the box, the machine also needs to be replaced. The volume of oil in the Toyota Corolla automatic transmission is 3.80 liters.

For every car owner, there comes a time when the engine oil in the engine must be changed. The Toyota Corolla is no exception to the rule. How long it takes to perform such an operation depends on many factors: this is the brand of the car, what fuel is used, what is the mode of operation.

For almost all cars, this occurs at a mileage of 10,000 km, but there are exceptions to the rules and the engine oil is changed earlier. If the machine is not used in winter, then in the spring this procedure should be mandatory. The operating conditions of the machine also play a role. When traveling only in urban conditions, the period of its change must be reduced by a couple of thousand, and if you drive mainly on highways, you can add 2 thousand km.

Why is an oil change necessary?

In any internal combustion engine, there are few rolling bearings, but many plain bearings. They are found in crankshafts and gas distribution mechanisms. Just for the lubrication of plain bearings, motor lubricating fluids are intended. During the operation of the motor occurs:

• loss of lubricating properties of the oil;
• removal of excess heat from rubbing parts;
• the engine is cleaned of soot and soot;
• an oil film is formed on the rubbing surfaces.

High-quality lubricants contain various additives that are added to improve its performance. In the process of work, they are produced or simply burn out. Therefore, it needs to be replaced.

For each type of internal combustion engine, its own brands of lubricants have been developed. They are summer, winter and demi-season, and are also characterized by such an indicator as viscosity. As can be seen from the foregoing, the role of lubricants in the operation of the motor is very high, and therefore their timely change is required.

What you can not do without when replacing

Toyota Corolla has come to the point where an oil change is simply necessary. For this you need to have:

1. A container with a capacity of approximately 5 liters for draining "working off".
2. Gloves to protect hands from burns, as the replacement is carried out on a hot engine.
3. The key is to loosen the drain plug, and then unscrew it with your hands.
4. Special key. It is needed in order to change the filter in the lubrication system.
5. A few rags so that you can wipe the drops on the floor.

How to change the lubricant

To do this, Toyota Corolla must be installed in a pit. If there is no viewing hole in the garage, then you can use a flyover or a lift. Next, you need to place the tool and empty containers more comfortably.

Start the engine and let the Toyota Corolla idle until the pressure light goes out. With the engine stopped, check the oil level again and correct if necessary.

The reliability of any car largely depends on regular and timely maintenance. Changing the Toyota Corolla oil is one of the main operations in the list of routine maintenance regularly carried out during the operation of this popular car.

Information! Known to all motorists, the Japanese passenger car has been mass-produced for more than 50 years (1966). During this time, constantly improving (11 generations), more than 40 million cars were produced. She has repeatedly been recognized as the most reliable in the class of compact cars.

Getting ready to replace

The replacement of used engine oil, or, as it is sometimes called, “workouts”, must be carried out in strict accordance with the requirements of the car’s operating manual.

What oil to pour

The type of engine oil that needs to be poured into the engine of a Toyota Corolla is indicated in the instruction manual without fail and depends on the year in which it was produced.

At the same time, Toyota Motor Corporation (1937) recommends using original Toyota Engine Oil oils or similar products from well-known companies Castrol, Mobil, etc.

• Toyota Corolla engines from 1st to 9th generation (1966-2008)

For engines installed in vehicles manufactured before 2009, an engine oil that meets the requirements of international standards API SL and ACEA A3 / B4 is suitable. Auto-lubricants manufactured according to these standards provide reliable protection of power units against wear in any operating modes and climatic conditions. They are also recommended for use in extended oil change intervals. This group includes oils with a viscosity of 0W30, 5W40, etc.

• Toyota Corolla engines from 9th to 11th generation (2006 - present)

Oil for engines that are installed in modern cars must comply with the international ILSAC GF-5 standard. They are characterized by a low content of phosphorus, which contributes to the low content of environmentally harmful substances in the exhaust gases. In addition, auto-lubricants manufactured to this standard reduce wear on engine parts and help reduce fuel consumption.

• Toyota Corolla diesel powertrains

When choosing a car lubricant for a diesel engine, you need to pay attention to the presence or absence of a particulate filter. At the same time, for car engines with installed particulate filters, it is recommended to use oils of the Low SAPS category, which are characterized by a low content of phosphorus and sulfur, as well as a low sulfate ash content. Their use helps to reduce fuel consumption and protect parts from premature wear. This category includes oils that meet the ACEA C2 standard (0W-30, 5W-30, etc.).

As for cars in which there is no particulate filter, auto-lubricants that comply with ACEA A5 / B5 and API SL / CF standards are recommended for their engines. They significantly reduce the wear of engine parts. Also, having high resistance to oxidation, oils of this category can be used for quite a long time in the most severe operating conditions.

When choosing engine oil, specialists working at service stations recommend giving preference to products:

• recommended by the vehicle manufacturer;
• the year and month of manufacture of which coincides with the date of replacement of the "working off".

Engine oil volume

A variety of power units were installed on cars in different years, differing both in cylinder displacement and power, and in torque.

Depending on which engine is installed in a particular model, the amount of oil that is poured into the engine can vary from 3.5 liters (cylinder capacity 1.3 liters, power 84 hp) to 4.3 liters (cylinder capacity 2.4 l, power 158 hp).

Where to pour oil

All engines that are installed in Toyota Corolla cars have an identical design. Engine oil in them is located in the lower part of the crankcase, and is poured through an oil filler neck located in the cylinder head, often covered with a decorative plastic panel. The neck is closed with a special stopper. Access to it is free, and the latter is unscrewed by the power of the hand.

Changing the oil

"Working off" and the oil filter must be changed regularly every 10 thousand kilometers. At the same time, experts recommend reducing this interval and replacing it after 5-7 thousand kilometers (depending on operating conditions).

IMPORTANT! The classic oil filter in a metal case was installed on the power units of Toyota Motor Corporation until 2010. Currently, a special filter insert is used instead, which, when replaced, is inserted into a special plastic cap. All other operations are identical.

Tools

Before proceeding with the oil change procedure, it is necessary to prepare the appropriate tools, fixtures and auxiliary materials. In the general case, in addition to new engine oil, their list includes:

1. a special oil filter puller (belt or chain) or a wrench for removing the oil insert cap (code 09228-06501);
2. funnel;
3. oil filter or insert;
4. socket wrench (head) for 14;
5. screwdriver;
6. container for draining old auto-lube (at least 5 l);
7. latex gloves;
8. rag.

Step-by-step instruction

Before proceeding with the procedure for replacing auto-lubrication, it is necessary to start and warm up the car engine to operating temperature. Due to this, the waste liquid will become more fluid, and the process of draining it will be faster. Then you need to drive the Toyota Corolla onto a flyover, a pit, or lift it on a lift.

The replacement procedure itself is as follows:

• substitute a container for draining the waste fluid under the drain hole in the crankcase;
• unscrew the oil filler cap;
• loosen the drain plug with a socket wrench, and then, taking special care (the drained liquid has a high temperature), unscrew it by hand (at the same time, it is necessary to ensure that the sealing ring does not fall into the container for the waste liquid);
• after waiting until the waste liquid has completely drained, rearrange the container with it under the oil filter;
• screw the drain plug into place, after wiping it and the edges of the hole with a rag;
• if the machine is installed on a lift, then it is lowered down;
• depending on the brand of Toyota Corolla, using a special puller or key, unscrew and remove the filter; unscrew the plastic cap and take out the filter insert; the filter or insert is thrown into a container with waste liquid;

Advice! Check the presence of the rubber gasket on the old filter. If it is not there, then it remains on the motor. In this case, the gasket must be removed from the engine and also sent to a container with waste fluid.

• wipe the installation site of the filter (insert) with a rag;
• a new rubber gasket is lubricated with engine oil;
• install a new oil filter or insert in place and twist them by hand;
• install a funnel in the filler neck;
• pour a liter of engine oil;
• after waiting until the filter element of the filter or the filter insert is saturated with oil, add oil. If the required amount of auto-lubrication is unknown, then it is added in small portions, checking the level with a dipstick;
• after the oil level reaches the required level (the oil mark must be between the MIN and MAX marks on the dipstick), the funnel is removed and the neck is closed with a stopper;
• start the engine and let it run until the oil pressure warning light goes out on the dashboard;
• while the car's engine is running, inspect the engine for leaks of technical fluids;
• turn off the engine and, after waiting a few minutes, take out the dipstick;
• after wiping the dipstick with a rag, lower it into the crankcase and check the level of the filled oil. If necessary, add the missing amount or drain the excess.

This completes the procedure for replacing engine oil in a Toyota Corolla engine.